[PATCH v3 3/3] ARM: dts: stm32: add initial support for stm32mp157-odyssey board
Ahmad Fatoum
a.fatoum at pengutronix.de
Fri Jul 24 05:16:42 EDT 2020
Hi,
On 7/23/20 9:43 PM, Marcin Słoniewski wrote:
> Hello Ahmad,
>
> First of all thank you very much for your feedback, it was very helpful!
>
> śr., 22 lip 2020 o 08:40 Ahmad Fatoum <a.fatoum at pengutronix.de> napisał(a):
>>
>> On 7/21/20 8:53 PM, Marcin Sloniewski wrote:
>>> Add support for Seeed Studio's stm32mp157c odyssey board.
>>> Board consists of SoM with stm32mp157c with 4GB eMMC and 512 MB DDR3 RAM
>>> and carrier board with USB and ETH interfaces, SD card connector,
>>> wifi and BT chip AP6236.
>>>
>>> In this patch only basic kernel boot is supported and interfacing
>>> SD card and on-board eMMC.
>>>
>>> Signed-off-by: Marcin Sloniewski <marcin.sloniewski at gmail.com>
>>> ---
>>>
>>> Changes in v3:
>>> - fix compilation on tip of stm32-next
>>> due to change in names for pinctrl
>>> - fix deprecated binding for led node
>>> - fix redundant "okay" statuses
>>> - add phy part number for eth in comment
>>
>> You didn't address all my feedback on v2.
> I posted today v4 of the patch-set with further changes.
> Regarding watchdog from pmic: when using this watchdog
> my board resets even though I feed the watchdog. I'm going to
> use the internal watchdog for now and keep in mind that this
> could be improved in future.
Who turns on the watchdog? If it's in the bootloader,
you can't rely on CONFIG_WATCHDOG_HANDLE_BOOT_ENABLED feeding it till
userspace takes over because the stpmic1_wdt doesn't populate
WDOG_HW_RUNNING in status.
> I changed phy address to 7, indeed you were right about it.
> But unfortunately even though I set the address correctly phy
> is still missing according to dmesg (I checked datasheet and schematics
> the address is surely correct now).
> That's something I would like to postpone a little bit as well for now.
You sent out v4 with a phy address of 7 though.
Did you get it working meanwhile?
>
>>
>>> Changes in v2:
>>> - add new odyssey dts to Makefile
>>>
>>> arch/arm/boot/dts/Makefile | 3 +-
>>> .../arm/boot/dts/stm32mp157c-odyssey-som.dtsi | 276 ++++++++++++++++++
>>> arch/arm/boot/dts/stm32mp157c-odyssey.dts | 72 +++++
>>> 3 files changed, 350 insertions(+), 1 deletion(-)
>>> create mode 100644 arch/arm/boot/dts/stm32mp157c-odyssey-som.dtsi
>>> create mode 100644 arch/arm/boot/dts/stm32mp157c-odyssey.dts
>>>
>>> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
>>> index e6a1cac0bfc7..a3ea2301c82c 100644
>>> --- a/arch/arm/boot/dts/Makefile
>>> +++ b/arch/arm/boot/dts/Makefile
>>> @@ -1047,7 +1047,8 @@ dtb-$(CONFIG_ARCH_STM32) += \
>>> stm32mp157c-dk2.dtb \
>>> stm32mp157c-ed1.dtb \
>>> stm32mp157c-ev1.dtb \
>>> - stm32mp157c-lxa-mc1.dtb
>>> + stm32mp157c-lxa-mc1.dtb \
>>> + stm32mp157c-odyssey.dtb
>>> dtb-$(CONFIG_MACH_SUN4I) += \
>>> sun4i-a10-a1000.dtb \
>>> sun4i-a10-ba10-tvbox.dtb \
>>> diff --git a/arch/arm/boot/dts/stm32mp157c-odyssey-som.dtsi b/arch/arm/boot/dts/stm32mp157c-odyssey-som.dtsi
>>> new file mode 100644
>>> index 000000000000..935632caddd6
>>> --- /dev/null
>>> +++ b/arch/arm/boot/dts/stm32mp157c-odyssey-som.dtsi
>>> @@ -0,0 +1,276 @@
>>> +// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
>>> +/*
>>> + * Copyright (C) 2020 Marcin Sloniewski <marcin.sloniewski at gmail.com>.
>>> + */
>>> +
>>> +/dts-v1/;
>>> +
>>> +#include "stm32mp157.dtsi"
>>> +#include "stm32mp15xc.dtsi"
>>> +#include "stm32mp15-pinctrl.dtsi"
>>> +#include "stm32mp15xxac-pinctrl.dtsi"
>>> +#include <dt-bindings/gpio/gpio.h>
>>> +#include <dt-bindings/leds/common.h>
>>> +#include <dt-bindings/mfd/st,stpmic1.h>
>>> +
>>> +/ {
>>> + model = "Seeed Studio Odyssey-STM32MP157C SOM";
>>> + compatible = "seeed,stm32mp157c-odyssey-som", "st,stm32mp157";
>>> +
>>> + memory at c0000000 {
>>> + device_type = "memory";
>>> + reg = <0xc0000000 0x20000000>;
>>> + };
>>> +
>>> + reserved-memory {
>>> + #address-cells = <1>;
>>> + #size-cells = <1>;
>>> + ranges;
>>> +
>>> + mcuram2: mcuram2 at 10000000 {
>>> + compatible = "shared-dma-pool";
>>> + reg = <0x10000000 0x40000>;
>>> + no-map;
>>> + };
>>> +
>>> + vdev0vring0: vdev0vring0 at 10040000 {
>>> + compatible = "shared-dma-pool";
>>> + reg = <0x10040000 0x1000>;
>>> + no-map;
>>> + };
>>> +
>>> + vdev0vring1: vdev0vring1 at 10041000 {
>>> + compatible = "shared-dma-pool";
>>> + reg = <0x10041000 0x1000>;
>>> + no-map;
>>> + };
>>> +
>>> + vdev0buffer: vdev0buffer at 10042000 {
>>> + compatible = "shared-dma-pool";
>>> + reg = <0x10042000 0x4000>;
>>> + no-map;
>>> + };
>>> +
>>> + mcuram: mcuram at 30000000 {
>>> + compatible = "shared-dma-pool";
>>> + reg = <0x30000000 0x40000>;
>>> + no-map;
>>> + };
>>> +
>>> + retram: retram at 38000000 {
>>> + compatible = "shared-dma-pool";
>>> + reg = <0x38000000 0x10000>;
>>> + no-map;
>>> + };
>>> +
>>> + gpu_reserved: gpu at d4000000 {
>>> + reg = <0xd4000000 0x4000000>;
>>> + no-map;
>>> + };
>>> + };
>>> +
>>> + led {
>>> + compatible = "gpio-leds";
>>> + led-blue {
>>> + color = <LED_COLOR_ID_BLUE>;
>>> + function = LED_FUNCTION_HEARTBEAT;
>>> + gpios = <&gpiog 3 GPIO_ACTIVE_HIGH>;
>>> + linux,default-trigger = "heartbeat";
>>> + };
>>> + };
>>> +};
>>> +
>>> +&gpu {
>>> + contiguous-area = <&gpu_reserved>;
>>> + status = "okay";
>>> +};
>>> +
>>> +&i2c2 {
>>> + pinctrl-names = "default";
>>> + pinctrl-0 = <&i2c2_pins_a>;
>>> + i2c-scl-rising-time-ns = <185>;
>>> + i2c-scl-falling-time-ns = <20>;
>>> + status = "okay";
>>> + /* spare dmas for other usage */
>>> + /delete-property/dmas;
>>> + /delete-property/dma-names;
>>> +
>>> + pmic: stpmic at 33 {
>>> + compatible = "st,stpmic1";
>>> + reg = <0x33>;
>>> + interrupts-extended = <&gpioa 0 IRQ_TYPE_EDGE_FALLING>;
>>> + interrupt-controller;
>>> + #interrupt-cells = <2>;
>>> +
>>> + regulators {
>>> + compatible = "st,stpmic1-regulators";
>>> + ldo1-supply = <&v3v3>;
>>> + ldo3-supply = <&vdd_ddr>;
>>> + ldo6-supply = <&v3v3>;
>>> + pwr_sw1-supply = <&bst_out>;
>>> + pwr_sw2-supply = <&bst_out>;
>>> +
>>> + vddcore: buck1 {
>>> + regulator-name = "vddcore";
>>> + regulator-min-microvolt = <800000>;
>>> + regulator-max-microvolt = <1350000>;
>>> + regulator-always-on;
>>> + regulator-initial-mode = <0>;
>>> + regulator-over-current-protection;
>>> + };
>>> +
>>> + vdd_ddr: buck2 {
>>> + regulator-name = "vdd_ddr";
>>> + regulator-min-microvolt = <1350000>;
>>> + regulator-max-microvolt = <1350000>;
>>> + regulator-always-on;
>>> + regulator-initial-mode = <0>;
>>> + regulator-over-current-protection;
>>> + };
>>> +
>>> + vdd: buck3 {
>>> + regulator-name = "vdd";
>>> + regulator-min-microvolt = <3300000>;
>>> + regulator-max-microvolt = <3300000>;
>>> + regulator-always-on;
>>> + st,mask-reset;
>>> + regulator-initial-mode = <0>;
>>> + regulator-over-current-protection;
>>> + };
>>> +
>>> + v3v3: buck4 {
>>> + regulator-name = "v3v3";
>>> + regulator-min-microvolt = <3300000>;
>>> + regulator-max-microvolt = <3300000>;
>>> + regulator-always-on;
>>> + regulator-over-current-protection;
>>> + regulator-initial-mode = <0>;
>>> + };
>>> +
>>> + v1v8_audio: ldo1 {
>>> + regulator-name = "v1v8_audio";
>>> + regulator-min-microvolt = <1800000>;
>>> + regulator-max-microvolt = <1800000>;
>>> + regulator-always-on;
>>> + interrupts = <IT_CURLIM_LDO1 0>;
>>> + };
>>> +
>>> + v3v3_hdmi: ldo2 {
>>> + regulator-name = "v3v3_hdmi";
>>> + regulator-min-microvolt = <3300000>;
>>> + regulator-max-microvolt = <3300000>;
>>> + regulator-always-on;
>>> + interrupts = <IT_CURLIM_LDO2 0>;
>>> + };
>>> +
>>> + vtt_ddr: ldo3 {
>>> + regulator-name = "vtt_ddr";
>>> + regulator-min-microvolt = <500000>;
>>> + regulator-max-microvolt = <750000>;
>>> + regulator-always-on;
>>> + regulator-over-current-protection;
>>> + };
>>> +
>>> + vdd_usb: ldo4 {
>>> + regulator-name = "vdd_usb";
>>> + regulator-min-microvolt = <3300000>;
>>> + regulator-max-microvolt = <3300000>;
>>> + interrupts = <IT_CURLIM_LDO4 0>;
>>> + };
>>> +
>>> + vdda: ldo5 {
>>> + regulator-name = "vdda";
>>> + regulator-min-microvolt = <2900000>;
>>> + regulator-max-microvolt = <2900000>;
>>> + interrupts = <IT_CURLIM_LDO5 0>;
>>> + regulator-boot-on;
>>> + };
>>> +
>>> + v1v2_hdmi: ldo6 {
>>> + regulator-name = "v1v2_hdmi";
>>> + regulator-min-microvolt = <1200000>;
>>> + regulator-max-microvolt = <1200000>;
>>> + regulator-always-on;
>>> + interrupts = <IT_CURLIM_LDO6 0>;
>>> + };
>>> +
>>> + vref_ddr: vref_ddr {
>>> + regulator-name = "vref_ddr";
>>> + regulator-always-on;
>>> + regulator-over-current-protection;
>>> + };
>>> +
>>> + bst_out: boost {
>>> + regulator-name = "bst_out";
>>> + interrupts = <IT_OCP_BOOST 0>;
>>> + };
>>> +
>>> + vbus_otg: pwr_sw1 {
>>> + regulator-name = "vbus_otg";
>>> + interrupts = <IT_OCP_OTG 0>;
>>> + };
>>> +
>>> + vbus_sw: pwr_sw2 {
>>> + regulator-name = "vbus_sw";
>>> + interrupts = <IT_OCP_SWOUT 0>;
>>> + regulator-active-discharge;
>>> + };
>>> + };
>>> +
>>> + onkey {
>>> + compatible = "st,stpmic1-onkey";
>>> + interrupts = <IT_PONKEY_F 0>, <IT_PONKEY_R 0>;
>>> + interrupt-names = "onkey-falling", "onkey-rising";
>>> + power-off-time-sec = <10>;
>>> + };
>>> +
>>> + watchdog {
>>> + compatible = "st,stpmic1-wdt";
>>> + status = "disabled";
>>> + };
>>> + };
>>> +};
>>> +
>>> +&ipcc {
>>> + status = "okay";
>>> +};
>>> +
>>> +&iwdg2 {
>>> + timeout-sec = <32>;
>>> + status = "okay";
>>> +};
>>> +
>>> +&m4_rproc {
>>> + memory-region = <&retram>, <&mcuram>, <&mcuram2>, <&vdev0vring0>,
>>> + <&vdev0vring1>, <&vdev0buffer>;
>>> + mboxes = <&ipcc 0>, <&ipcc 1>, <&ipcc 2>;
>>> + mbox-names = "vq0", "vq1", "shutdown";
>>> + interrupt-parent = <&exti>;
>>> + interrupts = <68 1>;
>>> + status = "okay";
>>> +};
>>> +
>>> +&rng1 {
>>> + status = "okay";
>>> +};
>>> +
>>> +&rtc {
>>> + status = "okay";
>>> +};
>>> +
>>> +&sdmmc2 {
>>> + pinctrl-names = "default", "opendrain", "sleep";
>>> + pinctrl-0 = <&sdmmc2_b4_pins_a &sdmmc2_d47_pins_a>;
>>> + pinctrl-1 = <&sdmmc2_b4_od_pins_a &sdmmc2_d47_pins_a>;
>>> + pinctrl-2 = <&sdmmc2_b4_sleep_pins_a &sdmmc2_d47_sleep_pins_a>;
>>> + non-removable;
>>> + no-sd;
>>> + no-sdio;
>>> + st,neg-edge;
>>> + bus-width = <4>;
>>> + vmmc-supply = <&v3v3>;
>>> + vqmmc-supply = <&v3v3>;
>>> + mmc-ddr-3_3v;
>>> + status = "okay";
>>> +};
>>> +
>>> diff --git a/arch/arm/boot/dts/stm32mp157c-odyssey.dts b/arch/arm/boot/dts/stm32mp157c-odyssey.dts
>>> new file mode 100644
>>> index 000000000000..09edf6afa155
>>> --- /dev/null
>>> +++ b/arch/arm/boot/dts/stm32mp157c-odyssey.dts
>>> @@ -0,0 +1,72 @@
>>> +// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
>>> +/*
>>> + * Copyright (C) 2020 Marcin Sloniewski <marcin.sloniewski at gmail.com>.
>>> + */
>>> +
>>> +/dts-v1/;
>>> +
>>> +#include "stm32mp157c-odyssey-som.dtsi"
>>> +
>>> +/ {
>>> + model = "Seeed Studio Odyssey-STM32MP157C Board";
>>> + compatible = "seeed,stm32mp157c-odyssey", "st,stm32mp157";
>>> +
>>> + aliases {
>>> + ethernet0 = ðernet0;
>>> + serial0 = &uart4;
>>> + };
>>> +
>>> + chosen {
>>> + stdout-path = "serial0:115200n8";
>>> + };
>>> +};
>>> +
>>> +ðernet0 {
>>> + status = "okay";
>>> + pinctrl-0 = <ðernet0_rgmii_pins_a>;
>>> + pinctrl-1 = <ðernet0_rgmii_sleep_pins_a>;
>>> + pinctrl-names = "default", "sleep";
>>> + phy-mode = "rgmii-id";
>>> + max-speed = <1000>;
>>> + phy-handle = <&phy0>;
>>> +
>>> + mdio0 {
>>> + #address-cells = <1>;
>>> + #size-cells = <0>;
>>> + compatible = "snps,dwmac-mdio";
>>> + phy0: ethernet-phy at 0 { /* KSZ9031RN */
>>> + reg = <0>;
>>> + };
>>> + };
>>> +};
>>> +
>>> +&i2c1 {
>>> + pinctrl-names = "default", "sleep";
>>> + pinctrl-0 = <&i2c1_pins_a>;
>>> + pinctrl-1 = <&i2c1_sleep_pins_a>;
>>> + i2c-scl-rising-time-ns = <100>;
>>> + i2c-scl-falling-time-ns = <7>;
>>> + status = "okay";
>>> + /delete-property/dmas;
>>> + /delete-property/dma-names;
>>> +};
>>> +
>>> +&sdmmc1 {
>>> + pinctrl-names = "default", "opendrain", "sleep";
>>> + pinctrl-0 = <&sdmmc1_b4_pins_a>;
>>> + pinctrl-1 = <&sdmmc1_b4_od_pins_a>;
>>> + pinctrl-2 = <&sdmmc1_b4_sleep_pins_a>;
>>> + cd-gpios = <&gpiob 7 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
>>> + disable-wp;
>>> + st,neg-edge;
>>> + bus-width = <4>;
>>> + vmmc-supply = <&v3v3>;
>>> + status = "okay";
>>> +};
>>> +
>>> +&uart4 {
>>> + pinctrl-names = "default";
>>> + pinctrl-0 = <&uart4_pins_a>;
>>> + status = "okay";
>>> +};
>>> +
>>>
>>
>> --
>> Pengutronix e.K. | |
>> Steuerwalder Str. 21 | http://www.pengutronix.de/ |
>> 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 |
>> Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |
>
--
Pengutronix e.K. | |
Steuerwalder Str. 21 | http://www.pengutronix.de/ |
31137 Hildesheim, Germany | Phone: +49-5121-206917-0 |
Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |
More information about the linux-arm-kernel
mailing list