[PATCH] ARM: dts: ZII: Disable HW Ethernet switch reset GPIO

[Chris Healy]

On Sun, Jul 19, 2020 at 8:15 PM Shawn Guo <shawnguo at kernel.org> wrote:
>
> On Wed, Jul 15, 2020 at 02:22:27PM -0700, Chris Healy wrote:
> > Disable Ethernet switch reset GPIO with ZII platforms that have it
> > enabled to sync up with existing ZII platforms that already have
> > it disabled.
>
> I do not follow it.  The reset GPIO is part of hardware description.  We
> shouldn't add or remove it for sake of sync-up with other platforms.

I see that my description is not very good.  What I should have said
is that we don't want to use the HW reset GPIO as it results in things
being done that we do not want done.  Specifically, when the switch is
hit with the HW reset GPIO, it results in the switch's copper PHYs
being HW reset which we want to avoid as this results in unnecessary
network downtime on a soft reboot of the processor.  With the HW reset
GPIO not in the devicetree description, the switch driver resorts to
doing a SW reset which resets the switch core but not the switch's
copper PHYs.  This results in a much shorter network downtime on a
soft reboot of the processor.

I can do a v2 of the patch with the description updated if you think
it would be appropriate.

>
> Shawn
>
> >
> > Signed-off-by: Chris Healy <cphealy at gmail.com>
> > ---
> >  arch/arm/boot/dts/vf610-zii-cfu1.dts      | 2 --
> >  arch/arm/boot/dts/vf610-zii-spb4.dts      | 2 --
> >  arch/arm/boot/dts/vf610-zii-ssmb-dtu.dts  | 2 --
> >  arch/arm/boot/dts/vf610-zii-ssmb-spu3.dts | 2 --
> >  4 files changed, 8 deletions(-)
> >
> > diff --git a/arch/arm/boot/dts/vf610-zii-cfu1.dts b/arch/arm/boot/dts/vf610-zii-cfu1.dts
> > index ce1920c052fc..c2668230a4c0 100644
> > --- a/arch/arm/boot/dts/vf610-zii-cfu1.dts
> > +++ b/arch/arm/boot/dts/vf610-zii-cfu1.dts
> > @@ -170,7 +170,6 @@
> >                       interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
> >                       interrupt-controller;
> >                       #interrupt-cells = <2>;
> > -                     reset-gpios = <&gpio3 11 GPIO_ACTIVE_LOW>;
> >
> >                       ports {
> >                               #address-cells = <1>;
> > @@ -354,7 +353,6 @@
> >       pinctrl_switch: switch-grp {
> >               fsl,pins = <
> >                       VF610_PAD_PTB28__GPIO_98                0x3061
> > -                     VF610_PAD_PTE2__GPIO_107                0x1042
> >               >;
> >       };
> >
> > diff --git a/arch/arm/boot/dts/vf610-zii-spb4.dts b/arch/arm/boot/dts/vf610-zii-spb4.dts
> > index 55b4201e27f6..261317340189 100644
> > --- a/arch/arm/boot/dts/vf610-zii-spb4.dts
> > +++ b/arch/arm/boot/dts/vf610-zii-spb4.dts
> > @@ -127,7 +127,6 @@
> >                       pinctrl-names = "default";
> >                       reg = <0>;
> >                       eeprom-length = <65536>;
> > -                     reset-gpios = <&gpio3 11 GPIO_ACTIVE_LOW>;
> >                       interrupt-parent = <&gpio3>;
> >                       interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
> >                       interrupt-controller;
> > @@ -312,7 +311,6 @@
> >
> >       pinctrl_gpio_switch0: pinctrl-gpio-switch0 {
> >               fsl,pins = <
> > -                     VF610_PAD_PTE2__GPIO_107                0x31c2
> >                       VF610_PAD_PTB28__GPIO_98                0x219d
> >               >;
> >       };
> > diff --git a/arch/arm/boot/dts/vf610-zii-ssmb-dtu.dts b/arch/arm/boot/dts/vf610-zii-ssmb-dtu.dts
> > index a6c22a79779e..e37b9643269b 100644
> > --- a/arch/arm/boot/dts/vf610-zii-ssmb-dtu.dts
> > +++ b/arch/arm/boot/dts/vf610-zii-ssmb-dtu.dts
> > @@ -113,7 +113,6 @@
> >                       pinctrl-names = "default";
> >                       reg = <0>;
> >                       eeprom-length = <65536>;
> > -                     reset-gpios = <&gpio3 11 GPIO_ACTIVE_LOW>;
> >                       interrupt-parent = <&gpio3>;
> >                       interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
> >                       interrupt-controller;
> > @@ -288,7 +287,6 @@
> >
> >       pinctrl_gpio_switch0: pinctrl-gpio-switch0 {
> >               fsl,pins = <
> > -                     VF610_PAD_PTE2__GPIO_107                0x31c2
> >                       VF610_PAD_PTB28__GPIO_98                0x219d
> >               >;
> >       };
> > diff --git a/arch/arm/boot/dts/vf610-zii-ssmb-spu3.dts b/arch/arm/boot/dts/vf610-zii-ssmb-spu3.dts
> > index 3d05c894bdc0..b3d6d4b9fa9c 100644
> > --- a/arch/arm/boot/dts/vf610-zii-ssmb-spu3.dts
> > +++ b/arch/arm/boot/dts/vf610-zii-ssmb-spu3.dts
> > @@ -141,7 +141,6 @@
> >                       pinctrl-names = "default";
> >                       reg = <0>;
> >                       eeprom-length = <65536>;
> > -                     reset-gpios = <&gpio3 11 GPIO_ACTIVE_LOW>;
> >                       interrupt-parent = <&gpio3>;
> >                       interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
> >                       interrupt-controller;
> > @@ -319,7 +318,6 @@
> >
> >       pinctrl_gpio_switch0: pinctrl-gpio-switch0 {
> >               fsl,pins = <
> > -                     VF610_PAD_PTE2__GPIO_107                0x31c2
> >                       VF610_PAD_PTB28__GPIO_98                0x219d
> >               >;
> >       };
> > --
> > 2.21.3
> >