[PATCH v6 10/10] arm64: dts: actions: Add uSD support for Cubieboard7

[Manivannan Sadhasivam]

On Sat, Jul 18, 2020 at 02:49:34PM +0530, Amit Singh Tomar wrote:
> This commit adds uSD support for Cubieboard7 board based on Actions Semi
> S700 SoC. SD0 is connected to uSD slot. Since there is no PMIC support
> added yet, fixed regulator has been used as a regulator node.
> 
> Signed-off-by: Amit Singh Tomar <amittomer25 at gmail.com>
> ---
> Changes since v5:
> 	* Removed the Fixed regulators as these are 
> 	  not needed.

I just asked you to remove the unused (ie. unreferenced fixed regulators) but
you seem to have removed sd_vcc which was supplied to uSD :/ How can the uSD
card work without a power supply? Forget the fact that the regulator was enabled
by bootloader but you are not properly describing it in DT here. The idea is to
model the actual hardware in DT and if you are not able to model the regulator
using PMIC then use fixed-regulator. Hope this makes it clear!

Thanks,
Mani

> Changes since v4:
>         * No change.
> Changes since v3:
>         * No change.
> Changes since v2:
>         * No change.
> Changes since v1:
>         * No change.
> Changes since RFC:
>         * No change.
> ---
>  arch/arm64/boot/dts/actions/s700-cubieboard7.dts | 22 ++++++++++++++++++++++
>  arch/arm64/boot/dts/actions/s700.dtsi            |  1 +
>  2 files changed, 23 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/actions/s700-cubieboard7.dts b/arch/arm64/boot/dts/actions/s700-cubieboard7.dts
> index 63e375cd9eb4..eaaf8f876203 100644
> --- a/arch/arm64/boot/dts/actions/s700-cubieboard7.dts
> +++ b/arch/arm64/boot/dts/actions/s700-cubieboard7.dts
> @@ -13,6 +13,7 @@
>  
>  	aliases {
>  		serial3 = &uart3;
> +		mmc0 = &mmc0;
>  	};
>  
>  	chosen {
> @@ -81,6 +82,14 @@
>  			bias-pull-up;
>  		};
>  	};
> +
> +	mmc0_default: mmc0_default {
> +		pinmux {
> +			groups = "sd0_d0_mfp", "sd0_d1_mfp", "sd0_d2_d3_mfp",
> +				 "sd0_cmd_mfp", "sd0_clk_mfp";
> +			function = "sd0";
> +		};
> +	};
>  };
>  
>  &timer {
> @@ -90,3 +99,16 @@
>  &uart3 {
>  	status = "okay";
>  };
> +
> +/* uSD */
> +&mmc0 {
> +	status = "okay";
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&mmc0_default>;
> +	cd-gpios = <&pinctrl 120 GPIO_ACTIVE_LOW>;
> +	no-sdio;
> +	no-mmc;
> +	no-1-8-v;
> +	bus-width = <4>;
> +};
> +
> diff --git a/arch/arm64/boot/dts/actions/s700.dtsi b/arch/arm64/boot/dts/actions/s700.dtsi
> index 9ed88aafc2da..ba498cf9217d 100644
> --- a/arch/arm64/boot/dts/actions/s700.dtsi
> +++ b/arch/arm64/boot/dts/actions/s700.dtsi
> @@ -4,6 +4,7 @@
>   */
>  
>  #include <dt-bindings/clock/actions,s700-cmu.h>
> +#include <dt-bindings/gpio/gpio.h>
>  #include <dt-bindings/interrupt-controller/arm-gic.h>
>  #include <dt-bindings/power/owl-s700-powergate.h>
>  #include <dt-bindings/reset/actions,s700-reset.h>
> -- 
> 2.7.4
>