[PATCH 0/1] usb: dwc3: meson-g12a: fix shared reset control use

Anand Moon linux.amoon at gmail.com
Sat Jul 18 05:54:31 EDT 2020


Hi Neil,

On Sat, 18 Jul 2020 at 14:16, Neil Armstrong <narmstrong at baylibre.com> wrote:
>
> Hi Anand,
>
> Le 18/07/2020 à 08:31, Anand Moon a écrit :
> > Hi Dan,
> >
> >>> Sorry for the _noise_ :‑(
> >>> This feature seems to be working fine with VRTC drivers.
> >>> I have tested this with a pre-compiled image of Archlinux distro.
> >>>
> >>> [root at alarm alarm]# uname -a
> >>> Linux alarm 5.7.8-1-ARCH #1 SMP Sun Jul 12 03:38:28 UTC 2020 aarch64 GNU/Linux
> >>> [root at alarm alarm]# rtcwake -s 30 -m mem
> >>> rtcwake: assuming RTC uses UTC ...
> >>> rtcwake: wakeup from "mem" using /dev/rtc0 at Thu Jan  1 00:10:14 1970
> >>> [  583.591477] PM: suspend entry (deep)
> >>> [  583.593737] Filesystems sync: 0.002 seconds
> >>> [  583.818967] Freezing user space processes ... (elapsed 0.005 seconds) done.
> >>> [  583.825802] OOM killer disabled.
> >>> [  583.828966] Freezing remaining freezable tasks ... (elapsed 0.003
> >>> seconds) done.
> >>> [  583.880280] sd 0:0:0:0: [sda] Synchronizing SCSI cache
> >>> [  584.020094] PM: suspend devices took 0.190 seconds
> >>> [  584.070586] Disabling non-boot CPUs ...
> >>> [  584.075037] CPU1: shutdown
> >>> [  584.075223] psci: CPU1 killed (polled 0 ms)
> >>> [  584.097199] CPU2: shutdown
> >>> [  584.098546] psci: CPU2 killed (polled 0 ms)
> >>> [  584.115370] CPU3: shutdown
> >>> [  584.116500] psci: CPU3 killed (polled 0 ms)
> >>> [  584.128116] CPU4: shutdown
> >>> [  584.129235] psci: CPU4 killed (polled 10 ms)
> >>> [  584.140122] CPU5: shutdown
> >>> [  584.147289] psci: CPU5 killed (polled 0 ms)
> >>> bl30 get wakeup sources!
> >>> process command 00000006
> >>> bl30 enter suspend!
> >>> Little core clk suspend rate 1896000000
> >>> Big core clk suspend rate 24000000
> >>> store restore gp0 pll
> >>> suspend_counter: 3
> >>> Enter ddr suspend
> >>> ddr suspend time: 16us
> >>> alarm=31S
> >>> process command 00000001
> >>> GPIOA_11/13 off
> >>> cec ver:2018/04/19
> >>> CEC cfg:0x0000
> >>> WAKEUP GPIO cfg:0x00000000
> >>> use vddee new table!
> >>> use vddee new table!
> >>> exit_reason:0x03
> >>> Enter ddr resume
> >>> DMC_DRAM_STAT3: 0x544
> >>> ddr resume time: 3188us
> >>> store restore gp0 pll
> >>> cfg15 33b00000
> >>> cfg15 33b00000
> >>> Li[  584.148720] Enabling non-boot CPUs ...
> >>> [  584.149124] Detected VIPT I-cache on CPU1
> >>> [  584.149167] CPU1: Booted secondary processor 0x0000000001 [0x410fd034]
> >>> [  584.149594] CPU1 is up
> >>> [  584.160687] Detected VIPT I-cache on CPU2
> >>> [  584.160730] arch_timer: CPU2: Trapping CNTVCT access
> >>> [  584.160741] CPU2: Booted secondary processor 0x0000000100 [0x410fd092]
> >>> [  584.161327] CPU2 is up
> >>> [  584.177645] Detected VIPT I-cache on CPU3
> >>> [  584.177668] arch_timer: CPU3: Trapping CNTVCT access
> >>> [  584.177675] CPU3: Booted secondary processor 0x0000000101 [0x410fd092]
> >>> [  584.178036] CPU3 is up
> >>> [  584.195338] Detected VIPT I-cache on CPU4
> >>> [  584.195361] arch_timer: CPU4: Trapping CNTVCT access
> >>> [  584.195368] CPU4: Booted secondary processor 0x0000000102 [0x410fd092]
> >>> [  584.195762] CPU4 is up
> >>> [  584.213002] Detected VIPT I-cache on CPU5
> >>> [  584.213024] arch_timer: CPU5: Trapping CNTVCT access
> >>> [  584.213032] CPU5: Booted secondary processor 0x0000000103 [0x410fd092]
> >>> [  584.213450] CPU5 is up
> >>> ttle core clk resume rate 1896000000
> >>> Big core clk resume rate 50000000
> >>> [  584.279042] meson8b-dwmac ff3f0000.ethernet eth0: No Safety
> >>> Features support found
> >>> [  584.281232] meson8b-dwmac ff3f0000.ethernet eth0: configuring for
> >>> phy/rgmii link mode
> >>> [  584.401216] usb usb1: root hub lost power or was reset
> >>> [  584.401470] usb usb2: root hub lost power or was reset
> >>> [  584.655446] dwc3-meson-g12a ffe09000.usb: switching to Device Mode
> >>> [  584.801108] usb 2-1: reset SuperSpeed Gen 1 USB device number 2
> >>> using xhci-hcd
> >>> [  584.979632] usb 1-1: reset high-speed USB device number 2 using xhci-hcd
> >>> [  585.260450] usb 2-1.1: reset SuperSpeed Gen 1 USB device number 3
> >>> using xhci-hcd
> >>> [  585.333303] PM: resume devices took 1.100 seconds
> >>> [  585.333507] OOM killer enabled.
> >>> [  585.335549] Restarting tasks ... done.
> >>> [  585.378044] PM: suspend exit
> >>> rtcwake: read rtc alarm failed: Invalid argument
> >>> [root at alarm alarm]#
> >>>
> >>> -Anand
> >>
> >> After confirming that the suspend resume feature is working correctly
> >> I found the solution to the reset warning on 5.8.x kernel
> >> Please can you try this following patch.
> >>
> >> $ cat resetwarn.patch
> >> diff --git a/drivers/usb/dwc3/dwc3-meson-g12a.c
> >> b/drivers/usb/dwc3/dwc3-meson-g12a.c
> >> index 1f7f4d88ed9d..60a6f49139fd 100644
> >> --- a/drivers/usb/dwc3/dwc3-meson-g12a.c
> >> +++ b/drivers/usb/dwc3/dwc3-meson-g12a.c
> >> @@ -730,7 +730,7 @@ static int dwc3_meson_g12a_probe(struct
> >> platform_device *pdev)
> >>
> >>         platform_set_drvdata(pdev, priv);
> >>
> >> -       priv->reset = devm_reset_control_get_shared(dev, NULL);
> >> +       priv->reset = devm_reset_control_get_shared(dev, "dwc3_meson");
> >>         if (IS_ERR(priv->reset)) {
> >>                 ret = PTR_ERR(priv->reset);
> >>                 dev_err(dev, "failed to get device reset, err=%d\n", ret);
> >>
> >> -Anand
> >
> > Apologize once again above changes break the usb functionality.
> > the correct fix along with these changes should be as below.
> > reset controllers need *resets* and *reset-names* to work correctly.
> >
> > But the _reset controller_ warning continues on suspend / resume features,
> > I am looking to find a FIX into this issue.
> >
> > diff --git a/arch/arm64/boot/dts/amlogic/meson-g12-common.dtsi
> > b/arch/arm64/boot/dts/amlogic/meson-g12-common.dtsi
> > index 593a006f4b7b..6d34dfa9825c 100644
> > --- a/arch/arm64/boot/dts/amlogic/meson-g12-common.dtsi
> > +++ b/arch/arm64/boot/dts/amlogic/meson-g12-common.dtsi
> > @@ -2318,6 +2318,7 @@ usb: usb at ffe09000 {
> >
> >                         clocks = <&clkc CLKID_USB>;
> >                         resets = <&reset RESET_USB>;
> > +                       reset-names = "dwc3_meson";
> >
> >                         dr_mode = "otg";
> >
> > -Anand
> >
>
>
> Theses 2 changes :
>
> >> -       priv->reset = devm_reset_control_get_shared(dev, NULL);
> >> +       priv->reset = devm_reset_control_get_shared(dev, "dwc3_meson");
>
> and
>
> > +                       reset-names = "dwc3_meson";
>
> are a no-op, since devm_reset_control_get_shared(dev, NULL) takes the
> first reset, with or without a reset-names.
>

Thanks for resolving my query. Sorry for the noise.

> Neil

-Anand



More information about the linux-arm-kernel mailing list