[PATCH v3 2/3] media: dt-bindings: media: xilinx: Add Xilinx UHD-SDI Receiver Subsystem
Laurent Pinchart
laurent.pinchart at ideasonboard.com
Wed Jul 15 12:29:01 EDT 2020
Hi Vishal,
Thank you for the patch.
On Mon, Jul 13, 2020 at 12:54:47PM -0600, Rob Herring wrote:
> On Thu, Jun 18, 2020 at 11:03:03AM +0530, Vishal Sagar wrote:
> > Add bindings documentation for Xilinx UHD-SDI Receiver Subsystem.
> >
> > The Xilinx UHD-SDI Receiver Subsystem consists of SMPTE UHD-SDI (RX) IP
> > core, an SDI RX to Video Bridge IP core to convert SDI video to native
> > video and a Video In to AXI4-Stream IP core to convert native video to
> > AXI4-Stream.
> >
> > Signed-off-by: Vishal Sagar <vishal.sagar at xilinx.com>
> > ---
> > v3
> > - bpc instead of bpp
> > - removed bpc as required property (default to 10 bpc)
> > - add dt-bindings/media/xilinx-sdi.h
> > - made line-rate as u32 instead of string
> > - fixed reg
> > - fixed s/upto/up to/
> >
> > v2
> > - Removed references to xlnx,video*
> > - Fixed as per Sakari Ailus and Rob Herring's comments
> > - Converted to yaml format
> >
> > .../bindings/media/xilinx/xlnx,sdirxss.yaml | 132 ++++++++++++++++++
> > include/dt-bindings/media/xilinx-sdi.h | 20 +++
> > 2 files changed, 152 insertions(+)
> > create mode 100644 Documentation/devicetree/bindings/media/xilinx/xlnx,sdirxss.yaml
> > create mode 100644 include/dt-bindings/media/xilinx-sdi.h
> >
> > diff --git a/Documentation/devicetree/bindings/media/xilinx/xlnx,sdirxss.yaml b/Documentation/devicetree/bindings/media/xilinx/xlnx,sdirxss.yaml
> > new file mode 100644
> > index 000000000000..6cfc18ca435f
> > --- /dev/null
> > +++ b/Documentation/devicetree/bindings/media/xilinx/xlnx,sdirxss.yaml
> > @@ -0,0 +1,132 @@
> > +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> > +%YAML 1.2
> > +---
> > +$id: http://devicetree.org/schemas/media/xilinx/xlnx,sdirxss.yaml#
> > +$schema: http://devicetree.org/meta-schemas/core.yaml#
> > +
> > +
I think a single blank line is enough.
> > +title: Xilinx SMPTE UHD-SDI Receiver Subsystem
> > +
> > +maintainers:
> > + - Vishal Sagar <vishal.sagar at xilinx.com>
> > +
> > +description: |
> > + The SMPTE UHD-SDI Receiver (RX) Subsystem allows you to quickly create systems
> > + based on SMPTE SDI protocols. It receives unaligned native SDI streams from
> > + the SDI GT PHY and outputs an AXI4-Stream video stream, native video, or
> > + native SDI using Xilinx transceivers as the physical layer.
> > +
> > + The subsystem consists of
> > + 1 - SMPTE UHD-SDI Rx
> > + 2 - SDI Rx to Native Video Bridge
> > + 3 - Video In to AXI4-Stream Bridge
> > +
> > + The subsystem can capture SDI streams in up to 12G mode 8 data streams and output
> > + a dual pixel per clock RGB/YUV444,422/420 10/12 bits per component AXI4-Stream.
> > +
> > +properties:
> > + compatible:
> > + items:
> > + - enum:
> > + - xlnx,v-smpte-uhdsdi-rx-ss-2.0
>
> Should be indented 2 more spaces.
Or you could simply use
properties:
compatible:
const: xlnx,v-smpte-uhdsdi-rx-ss-2.0
> > +
> > + reg:
> > + maxItems: 1
> > +
> > + interrupts:
> > + maxItems: 1
> > +
> > + clocks:
> > + description: List of clock specifiers
>
> Drop. That's every 'clocks' property.
>
> > + items:
> > + - description: AXI4-Lite clock
> > + - description: SMPTE UHD-SDI Rx core clock
> > + - description: Video clock
> > +
> > + clock-names:
> > + items:
> > + - const: s_axi_aclk
> > + - const: sdi_rx_clk
> > + - const: video_out_clk
> > +
> > + xlnx,bpc:
> > + description: Bits per component supported. Can be 10 or 12 bits per component only.
> > + allOf:
>
> You can drop the 'allOf' now.
>
> > + - $ref: "/schemas/types.yaml#/definitions/uint32"
> > + - enum: [10, 12]
>
> Seems like this should be a standard property?
Rob, if my understanding is correct, this tells for how many bits per
component the IP core has been synthesized. I think it qualifies as a
vendor property, as how to express constraints on supported formats (for
IP cores that can be synthesized with different options) is highly
vendor-specific.
Vishal, I think the question I asked in the review of v2 fell through
the cracks. Is the documentation for the new IP core version available ?
Should this property only be allowed for the new version, given that in
v2.0 the BPC is fixed to 10 ?
> > +
> > + xlnx,line-rate:
> > + description: |
> > + The maximum mode supported by the design. Possible values are as below
> > + 0 - XSDI_STD_3G - 3G mode
> > + 1 - XSDI_STD_6G - 6G mode
> > + 2 - XSDI_STD_12G_8DS - 12G mode with 8 data streams
> > + allOf:
> > + - $ref: "/schemas/types.yaml#/definitions/uint32"
> > + - enum: [0, 1, 2]
>
> Standard?
For this one, I'm not sure. There's little support for SDI in the
kernel, and I'm sure we'll get this wrong the first time. I'd rather try
not to over-standardize properties before we have more examples.
> > +
> > + xlnx,include-edh:
> > + type: boolean
> > + description: |
> > + This is present when the Error Detection and Handling processor is
> > + enabled in design.
> > +
> > + ports:
> > + type: object
> > + description: |
> > + Generally the SDI port is connected to a device like SDI Broadcast camera
> > + which is independently controlled. Hence port at 0 is a source port which can be
> > + connected to downstream IP which can work with AXI4 Stream data.
> > + properties:
> > + port at 0:
> > + type: object
> > + description: Source port
> > + properties:
> > + reg:
> > + const: 0
> > + endpoint:
> > + type: object
> > + properties:
> > + remote-endpoint: true
> > + required:
> > + - remote-endpoint
> > + additionalProperties: false
> > + additionalProperties: false
Same here, I explained in the review of v2 that we should have an input
port.
> > +
> > +required:
> > + - compatible
> > + - reg
> > + - interrupts
> > + - clocks
> > + - clock-names
> > + - xlnx,line-rate
> > + - ports
> > +
> > +additionalProperties: false
> > +
> > +examples:
> > + - |
> > + #include <dt-bindings/media/xilinx-sdi.h>
> > + uhdsdirxss: v-smpte-uhdsdi-rxss at 80000000 {
The label is not used, you can drop it.
> > + compatible = "xlnx,v-smpte-uhdsdi-rx-ss-2.0";
> > + interrupt-parent = <&gic>;
> > + interrupts = <0 89 4>;
> > + reg = <0x80000000 0x10000>;
> > + xlnx,include-edh;
> > + xlnx,line-rate = <XSDI_STD_12G_8DS>;
> > + clocks = <&clk_1>, <&si570_1>, <&clk_2>;
> > + clock-names = "s_axi_aclk", "sdi_rx_clk", "video_out_clk";
> > + xlnx,bpc = <10>;
I would group the xlnx,* properties after the standard properties.
> > +
> > + ports {
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > + port at 0 {
> > + reg = <0>;
> > + sdirx_out: endpoint {
> > + remote-endpoint = <&vcap_sdirx_in>;
> > + };
> > + };
> > + };
> > + };
> > +...
> > diff --git a/include/dt-bindings/media/xilinx-sdi.h b/include/dt-bindings/media/xilinx-sdi.h
> > new file mode 100644
> > index 000000000000..11938fade041
> > --- /dev/null
> > +++ b/include/dt-bindings/media/xilinx-sdi.h
> > @@ -0,0 +1,20 @@
> > +/* SPDX-License-Identifier: GPL-2.0 */
> > +/*
> > + * Xilinx SDI device tree bindings
> > + *
> > + * Copyright (C) 2020 Xilinx, Inc.
> > + *
> > + * Contacts: Vishal Sagar <vishal.sagar at xilinx.com>
> > + */
> > +
> > +#ifndef __DT_BINDINGS_MEDIA_XILINX_SDI_H__
> > +#define __DT_BINDINGS_MEDIA_XILINX_SDI_H__
> > +
> > +/*
> > + * SDI Configurations
> > + */
> > +#define XSDI_STD_3G 0
> > +#define XSDI_STD_6G 1
> > +#define XSDI_STD_12G_8DS 2
> > +
> > +#endif /* __DT_BINDINGS_MEDIA_XILINX_SDI_H__ */
--
Regards,
Laurent Pinchart
More information about the linux-arm-kernel
mailing list