[PATCH v3] PCI: aardvark: Don't touch PCIe registers if no card connected

[Pali Rohár]

On Thursday 09 July 2020 12:35:09 Lorenzo Pieralisi wrote:
> On Thu, Jul 02, 2020 at 10:30:36AM +0200, Pali Rohár wrote:
> > When there is no PCIe card connected and advk_pcie_rd_conf() or
> > advk_pcie_wr_conf() is called for PCI bus which doesn't belong to emulated
> > root bridge, the aardvark driver throws the following error message:
> > 
> >   advk-pcie d0070000.pcie: config read/write timed out
> > 
> > Obviously accessing PCIe registers of disconnected card is not possible.
> > 
> > Extend check in advk_pcie_valid_device() function for validating
> > availability of PCIe bus. If PCIe link is down, then the device is marked
> > as Not Found and the driver does not try to access these registers.
> > 
> > This is just an optimization to prevent accessing PCIe registers when card
> > is disconnected. Trying to access PCIe registers of disconnected card does
> > not cause any crash, kernel just needs to wait for a timeout. So if card
> > disappear immediately after checking for PCIe link (before accessing PCIe
> > registers), it does not cause any problems.
> > 
> > Signed-off-by: Pali Rohár <pali at kernel.org>
> > 
> > ---
> > Changes in V3:
> > * Add comment to the code
> > Changes in V2:
> > * Update commit message, mention that this is optimization
> > ---
> >  drivers/pci/controller/pci-aardvark.c | 7 +++++++
> >  1 file changed, 7 insertions(+)
> > 
> > diff --git a/drivers/pci/controller/pci-aardvark.c b/drivers/pci/controller/pci-aardvark.c
> > index 90ff291c24f0..d18f389b36a1 100644
> > --- a/drivers/pci/controller/pci-aardvark.c
> > +++ b/drivers/pci/controller/pci-aardvark.c
> > @@ -644,6 +644,13 @@ static bool advk_pcie_valid_device(struct advk_pcie *pcie, struct pci_bus *bus,
> >  	if ((bus->number == pcie->root_bus_nr) && PCI_SLOT(devfn) != 0)
> >  		return false;
> >  
> > +	/*
> > +	 * If the link goes down after we check for link-up, nothing bad
> > +	 * happens but the config access times out.
> > +	 */
> > +	if (bus->number != pcie->root_bus_nr && !advk_pcie_link_up(pcie))
> > +		return false;
> > +
> >  	return true;
> >  }
> 
> Question: this basically means that you can only effectively enumerate
> bus number == root_bus_nr and AFAICS if at probe the link did not
> come up it will never do, will it ?
> 
> Isn't this equivalent to limiting the bus numbers the bridge is capable
> of handling ?
> 
> Reworded: if in advk_pcie_setup_hw() the link does not come up, what's
> the point of trying to enumerate the bus hierarchy below the root bus ?

Hello Lorenzo!

PCIe link can theoretically come up even after boot, but aardvark driver
currently does not support link detection at runtime. So it checks and
enumerate device only at probe time.

I do not know if hardware has some mechanism to inform kernel that PCIe
link come up (or down) and re-enumeration is required. Or the only
option is polling via advk_pcie_link_up().

So if device is not visible at the probe time then it would not appear
in system and cannot be used. This is current state.

Just to note that our hardware does not support physical hotplug of
mPCIe cards. You need to connect card when board is powered off.

So if at the aardvark probe time PCIe link is not up then trying to
enumerate devices under (software) root bridge is not needed. But it is
needed to register/enumerate software root bridge device and currently
both is done by one (recursive) call pci_host_probe().