[PATCH v4 72/78] drm/vc4: hdmi: Do the VID_CTL configuration at once

Maxime Ripard maxime at cerno.tech
Wed Jul 8 13:42:20 EDT 2020


The VID_CTL setup is done in several places in the driver even though it's
not really required. Let's simplify it a bit to do the configuration in one
go.

Signed-off-by: Maxime Ripard <maxime at cerno.tech>
---
 drivers/gpu/drm/vc4/vc4_hdmi.c | 14 ++++++--------
 1 file changed, 6 insertions(+), 8 deletions(-)

diff --git a/drivers/gpu/drm/vc4/vc4_hdmi.c b/drivers/gpu/drm/vc4/vc4_hdmi.c
index bbe521ab000b..f56a718a3643 100644
--- a/drivers/gpu/drm/vc4/vc4_hdmi.c
+++ b/drivers/gpu/drm/vc4/vc4_hdmi.c
@@ -428,10 +428,6 @@ static void vc4_hdmi_set_timings(struct vc4_hdmi *vc4_hdmi,
 
 	HDMI_WRITE(HDMI_VERTB0, vertb_even);
 	HDMI_WRITE(HDMI_VERTB1, vertb);
-
-	HDMI_WRITE(HDMI_VID_CTL,
-		   (vsync_pos ? 0 : VC4_HD_VID_CTL_VSYNC_LOW) |
-		   (hsync_pos ? 0 : VC4_HD_VID_CTL_HSYNC_LOW));
 }
 
 static void vc4_hdmi_recenter_fifo(struct vc4_hdmi *vc4_hdmi)
@@ -520,8 +516,6 @@ static void vc4_hdmi_encoder_pre_crtc_configure(struct drm_encoder *encoder)
 	if (vc4_hdmi->variant->phy_init)
 		vc4_hdmi->variant->phy_init(vc4_hdmi, mode);
 
-	HDMI_WRITE(HDMI_VID_CTL, 0);
-
 	HDMI_WRITE(HDMI_SCHEDULER_CONTROL,
 		   HDMI_READ(HDMI_SCHEDULER_CONTROL) |
 		   VC4_HDMI_SCHEDULER_CONTROL_MANUAL_FORMAT |
@@ -555,15 +549,19 @@ static void vc4_hdmi_encoder_pre_crtc_enable(struct drm_encoder *encoder)
 
 static void vc4_hdmi_encoder_post_crtc_enable(struct drm_encoder *encoder)
 {
+	struct drm_display_mode *mode = &encoder->crtc->state->adjusted_mode;
 	struct vc4_hdmi *vc4_hdmi = encoder_to_vc4_hdmi(encoder);
 	struct vc4_hdmi_encoder *vc4_encoder = to_vc4_hdmi_encoder(encoder);
+	bool hsync_pos = mode->flags & DRM_MODE_FLAG_PHSYNC;
+	bool vsync_pos = mode->flags & DRM_MODE_FLAG_PVSYNC;
 	int ret;
 
 	HDMI_WRITE(HDMI_VID_CTL,
-		   HDMI_READ(HDMI_VID_CTL) |
 		   VC4_HD_VID_CTL_ENABLE |
 		   VC4_HD_VID_CTL_UNDERFLOW_ENABLE |
-		   VC4_HD_VID_CTL_FRAME_COUNTER_RESET);
+		   VC4_HD_VID_CTL_FRAME_COUNTER_RESET |
+		   (vsync_pos ? 0 : VC4_HD_VID_CTL_VSYNC_LOW) |
+		   (hsync_pos ? 0 : VC4_HD_VID_CTL_HSYNC_LOW));
 
 	if (vc4_encoder->hdmi_monitor) {
 		HDMI_WRITE(HDMI_SCHEDULER_CONTROL,
-- 
git-series 0.9.1



More information about the linux-arm-kernel mailing list