[PATCH v7 2/7] dt-bindings: pinctrl: add bindings for MediaTek MT6779 SoC
Hanks Chen
hanks.chen at mediatek.com
Tue Jul 7 07:05:17 EDT 2020
On Thu, 2020-07-02 at 14:58 -0600, Rob Herring wrote:
> On Thu, Jul 02, 2020 at 08:57:05PM +0800, Hanks Chen wrote:
> > From: Andy Teng <andy.teng at mediatek.com>
> >
> > Add devicetree bindings for MediaTek MT6779 pinctrl driver.
> >
> > Signed-off-by: Andy Teng <andy.teng at mediatek.com>
> > ---
> > .../bindings/pinctrl/mediatek,mt6779-pinctrl.yaml | 210 ++++++++++++++++++++
> > 1 file changed, 210 insertions(+)
> > create mode 100644 Documentation/devicetree/bindings/pinctrl/mediatek,mt6779-pinctrl.yaml
> >
> > diff --git a/Documentation/devicetree/bindings/pinctrl/mediatek,mt6779-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/mediatek,mt6779-pinctrl.yaml
> > new file mode 100644
> > index 0000000..3a9fc4d
> > --- /dev/null
> > +++ b/Documentation/devicetree/bindings/pinctrl/mediatek,mt6779-pinctrl.yaml
> > @@ -0,0 +1,210 @@
> > +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> > +%YAML 1.2
> > +---
> > +$id: https://urldefense.com/v3/__http://devicetree.org/schemas/pinctrl/mediatek,mt6779-pinctrl.yaml*__;Iw!!CTRNKA9wMg0ARbw!0474C4nwnSzS27r76why4qthf5712hrWflC57fdhSU7LzHZYpD7W0t5ZhJBgmnpF-A$
> > +$schema: https://urldefense.com/v3/__http://devicetree.org/meta-schemas/core.yaml*__;Iw!!CTRNKA9wMg0ARbw!0474C4nwnSzS27r76why4qthf5712hrWflC57fdhSU7LzHZYpD7W0t5ZhJAzv-fiRw$
> > +
> > +title: Mediatek MT6779 Pin Controller Device Tree Bindings
> > +
> > +maintainers:
> > + - Andy Teng <andy.teng at mediatek.com>
> > +
> > +description: |+
> > + The pin controller node should be the child of a syscon node with the
> > + required property:
> > + - compatible: "syscon"
> > +
> > +properties:
> > + compatible:
> > + const: mediatek,mt6779-pinctrl
> > +
> > + reg:
> > + minItems: 9
> > + maxItems: 9
> > + description: |
> > + physical address base for gpio-related control registers.
>
> Need to describe what each entry is.
>
> items:
> - description: ...
> - description: ...
> - description: ...
>
Got it, I'll add description in next version.
Thanks!
> > +
> > + reg-names:
> > + description: |
> > + GPIO base register names. The names are "gpio", "iocfg_rm",
> > + "iocfg_br", "iocfg_lm", "iocfg_lb", "iocfg_rt", "iocfg_lt",
> > + "iocfg_tl", "eint";
>
> The names should be a schema.
>
Got it, I'll fix it.
>
> > +
> > + gpio-controller: true
> > +
> > + "#gpio-cells":
> > + const: 2
> > + description: |
> > + Number of cells in GPIO specifier. Since the generic GPIO
> > + binding is used, the amount of cells must be specified as 2. See the below
> > + mentioned gpio binding representation for description of particular cells.
> > +
> > + gpio-ranges:
> > + minItems: 1
> > + maxItems: 5
> > + description: |
> > + GPIO valid number range.
> > +
> > + interrupt-controller: true
> > +
> > + interrupts:
> > + maxItems: 1
> > + description: |
> > + Specifies the summary IRQ.
> > +
> > + "#interrupt-cells":
> > + const: 2
> > +
> > +required:
> > + - compatible
> > + - reg
> > + - reg-names
> > + - gpio-controller
> > + - "#gpio-cells"
> > + - gpio-ranges
> > + - interrupt-controller
> > + - interrupts
> > + - "#interrupt-cells"
> > +
> > +patternProperties:
> > + '-[0-9]*$':
> > + type: object
> > + patternProperties:
> > + '-pins*$':
> > + type: object
> > + description: |
> > + A pinctrl node should contain at least one subnodes representing the
> > + pinctrl groups available on the machine. Each subnode will list the
> > + pins it needs, and how they should be configured, with regard to muxer
> > + configuration, pullups, drive strength, input enable/disable and input schmitt.
>
> Need to include the pinconf schema here.
Got it, I'll add it in next version.
>
> > +
> > + properties:
> > + pinmux:
> > + description:
> > + integer array, represents gpio pin number and mux setting.
> > + Supported pin number and mux varies for different SoCs, and are defined
> > + as macros in boot/dts/<soc>-pinfunc.h directly.
> > +
> > + bias-disable:
> > + type: boolean
>
> Don't redefine the type. Just indicate what common properties are used:
>
> bias-disable: true
Got it, I'll fix it in next version.
>
> > +
> > + bias-pull-up:
> > + type: boolean
> > +
> > + bias-pull-down:
> > + type: boolean
> > +
> > + input-enable:
> > + type: boolean
> > +
> > + input-disable:
> > + type: boolean
> > +
> > + output-low:
> > + type: boolean
> > +
> > + output-high:
> > + type: boolean
> > +
> > + input-schmitt-enable:
> > + type: boolean
> > +
> > + input-schmitt-disable:
> > + type: boolean
> > +
> > + mediatek,pull-up-adv:
> > + description: |
> > + Pull up setings for 2 pull resistors, R0 and R1. User can
> > + configure those special pins. Valid arguments are described as below:
> > + 0: (R1, R0) = (0, 0) which means R1 disabled and R0 disabled.
> > + 1: (R1, R0) = (0, 1) which means R1 disabled and R0 enabled.
> > + 2: (R1, R0) = (1, 0) which means R1 enabled and R0 disabled.
> > + 3: (R1, R0) = (1, 1) which means R1 enabled and R0 enabled.
> > + allOf:
>
> You can drop the allOf now.
Got it, I'll drop it in next version.
Thanks
>
> > + - $ref: /schemas/types.yaml#/definitions/uint32
> > + - enum: [0, 1, 2, 3]
> > +
> > + mediatek,pull-down-adv:
> > + description: |
> > + Pull down settings for 2 pull resistors, R0 and R1. User can
> > + configure those special pins. Valid arguments are described as below:
> > + 0: (R1, R0) = (0, 0) which means R1 disabled and R0 disabled.
> > + 1: (R1, R0) = (0, 1) which means R1 disabled and R0 enabled.
> > + 2: (R1, R0) = (1, 0) which means R1 enabled and R0 disabled.
> > + 3: (R1, R0) = (1, 1) which means R1 enabled and R0 enabled.
> > + allOf:
> > + - $ref: /schemas/types.yaml#/definitions/uint32
> > + - enum: [0, 1, 2, 3]
> > +
> > + drive-strength:
> > + description: |
> > + Selects the drive strength for the specified pins in mA.
> > + allOf:
> > + - $ref: /schemas/types.yaml#/definitions/uint32
> > + - enum: [2, 4, 6, 8, 10, 12, 14, 16]
> > +
> > + required:
> > + - pinmux
> > +
> > + additionalProperties: false
> > +
> > +additionalProperties: false
> > +
> > +examples:
> > + - |
> > + #include <dt-bindings/interrupt-controller/irq.h>
> > + #include <dt-bindings/interrupt-controller/arm-gic.h>
> > + #include <dt-bindings/pinctrl/mt6779-pinfunc.h>
> > +
> > + pio: pinctrl at 10005000 {
> > + compatible = "mediatek,mt6779-pinctrl";
> > + reg = <0 0x10005000 0 0x1000>,
> > + <0 0x11c20000 0 0x1000>,
> > + <0 0x11d10000 0 0x1000>,
> > + <0 0x11e20000 0 0x1000>,
> > + <0 0x11e70000 0 0x1000>,
> > + <0 0x11ea0000 0 0x1000>,
> > + <0 0x11f20000 0 0x1000>,
> > + <0 0x11f30000 0 0x1000>,
> > + <0 0x1000b000 0 0x1000>;
> > + reg-names = "gpio", "iocfg_rm",
> > + "iocfg_br", "iocfg_lm",
> > + "iocfg_lb", "iocfg_rt",
> > + "iocfg_lt", "iocfg_tl",
> > + "eint";
> > + gpio-controller;
> > + #gpio-cells = <2>;
> > + gpio-ranges = <&pio 0 0 210>;
> > + interrupt-controller;
> > + #interrupt-cells = <2>;
> > + interrupts = <GIC_SPI 204 IRQ_TYPE_LEVEL_HIGH>;
> > +
> > + mmc0_pins_default: mmc0-0 {
> > + cmd-dat-pins {
> > + pinmux = <PINMUX_GPIO168__FUNC_MSDC0_DAT0>,
> > + <PINMUX_GPIO172__FUNC_MSDC0_DAT1>,
> > + <PINMUX_GPIO169__FUNC_MSDC0_DAT2>,
> > + <PINMUX_GPIO177__FUNC_MSDC0_DAT3>,
> > + <PINMUX_GPIO170__FUNC_MSDC0_DAT4>,
> > + <PINMUX_GPIO173__FUNC_MSDC0_DAT5>,
> > + <PINMUX_GPIO171__FUNC_MSDC0_DAT6>,
> > + <PINMUX_GPIO174__FUNC_MSDC0_DAT7>,
> > + <PINMUX_GPIO167__FUNC_MSDC0_CMD>;
> > + input-enable;
> > + mediatek,pull-up-adv = <1>;
> > + };
> > + clk-pins {
> > + pinmux = <PINMUX_GPIO176__FUNC_MSDC0_CLK>;
> > + mediatek,pull-down-adv = <2>;
> > + };
> > + rst-pins {
> > + pinmux = <PINMUX_GPIO178__FUNC_MSDC0_RSTB>;
> > + mediatek,pull-up-adv = <0>;
> > + };
> > + };
> > + };
> > +
> > + mmc0 {
> > + pinctrl-0 = <&mmc0_pins_default>;
> > + pinctrl-names = "default";
> > + };
> > --
> > 1.7.9.5
>
> _______________________________________________
> Linux-mediatek mailing list
> Linux-mediatek at lists.infradead.org
> https://urldefense.com/v3/__http://lists.infradead.org/mailman/listinfo/linux-mediatek__;!!CTRNKA9wMg0ARbw!0474C4nwnSzS27r76why4qthf5712hrWflC57fdhSU7LzHZYpD7W0t5ZhJDOADfrzw$
More information about the linux-arm-kernel
mailing list