[PATCH v3 4/4] arm64: dts: marvell: add SMMU support

[Tomasz Nowicki]

On 03.07.2020 11:16, Robin Murphy wrote:
> On 2020-07-02 21:16, Tomasz Nowicki wrote:
>> From: Marcin Wojtas <mw at semihalf.com>
>>
>> Add IOMMU node for Marvell AP806 based SoCs together with platform
>> and PCI device Stream ID mapping.
>>
>> Signed-off-by: Marcin Wojtas <mw at semihalf.com>
>> Signed-off-by: Tomasz Nowicki <tn at semihalf.com>
>> ---
>>   arch/arm64/boot/dts/marvell/armada-8040.dtsi  | 36 +++++++++++++++++++
>>   arch/arm64/boot/dts/marvell/armada-ap80x.dtsi | 17 +++++++++
>>   2 files changed, 53 insertions(+)
>>
>> diff --git a/arch/arm64/boot/dts/marvell/armada-8040.dtsi 
>> b/arch/arm64/boot/dts/marvell/armada-8040.dtsi
>> index 7699b19224c2..25c1df709f72 100644
>> --- a/arch/arm64/boot/dts/marvell/armada-8040.dtsi
>> +++ b/arch/arm64/boot/dts/marvell/armada-8040.dtsi
>> @@ -23,3 +23,39 @@
>>   &cp0_rtc {
>>       status = "disabled";
>>   };
>> +
>> +&cp0_usb3_0 {
>> +    iommus = <&smmu 0x440>;
>> +};
>> +
>> +&cp0_usb3_1 {
>> +    iommus = <&smmu 0x441>;
>> +};
>> +
>> +&cp0_sata0 {
>> +    iommus = <&smmu 0x444>;
>> +};
>> +
>> +&cp0_sdhci0 {
>> +    iommus = <&smmu 0x445>;
>> +};
>> +
>> +&cp1_sata0 {
>> +    iommus = <&smmu 0x454>;
>> +};
>> +
>> +&cp1_usb3_0 {
>> +    iommus = <&smmu 0x450>;
>> +};
>> +
>> +&cp1_usb3_1 {
>> +    iommus = <&smmu 0x451>;
>> +};
>> +
>> +&cp0_pcie0 {
>> +    iommu-map =
>> +        <0x0   &smmu 0x480 0x20>,
>> +        <0x100 &smmu 0x4a0 0x20>,
>> +        <0x200 &smmu 0x4c0 0x20>;
>> +    iommu-map-mask = <0x031f>;
> 
> Nice! I do like a good compressed mapping :D
> 
>> +};
>> diff --git a/arch/arm64/boot/dts/marvell/armada-ap80x.dtsi 
>> b/arch/arm64/boot/dts/marvell/armada-ap80x.dtsi
>> index 7f9b9a647717..ded8b8082d79 100644
>> --- a/arch/arm64/boot/dts/marvell/armada-ap80x.dtsi
>> +++ b/arch/arm64/boot/dts/marvell/armada-ap80x.dtsi
>> @@ -56,6 +56,23 @@
>>               compatible = "simple-bus";
>>               ranges = <0x0 0x0 0xf0000000 0x1000000>;
>> +            smmu: iommu at 5000000 {
>> +                compatible = "marvell,ap806-smmu-500", "arm,mmu-500";
>> +                reg = <0x100000 0x100000>;
>> +                dma-coherent;
>> +                #iommu-cells = <1>;
>> +                #global-interrupts = <1>;
>> +                interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>,
>> +                         <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>,
>> +                         <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>,
>> +                         <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>,
>> +                         <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>,
>> +                         <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>,
>> +                         <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>,
>> +                         <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>,
>> +                         <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
> 
> I'd recommend you have the node disabled by default here, then 
> explicitly enable it in armada-8040.dtsi where you add the Stream IDs. 
> Otherwise it will also end up enabled for 8020, 70x0, etc. where 
> disable_bypass will then catastrophically break everything.
> 

Good point! I will fix this.

Thanks,
Tomasz