[PATCH v3 4/8] mux: sparx5: Add Sparx5 SPI mux driver
Lars Povlsen
lars.povlsen at microchip.com
Fri Jul 3 05:14:00 EDT 2020
Peter Rosin writes:
> Hi!
>
> On 2020-07-02 12:13, Lars Povlsen wrote:
>> The Sparx5 mux driver may be used to control selecting between two
>> alternate SPI bus segments connected to the SPI controller
>> (spi-dw-mmio).
>>
>> Signed-off-by: Lars Povlsen <lars.povlsen at microchip.com>
>> ---
>> drivers/mux/Makefile | 2 +
>> drivers/mux/sparx5-spi.c | 138 +++++++++++++++++++++++++++++++++++++++
>> 2 files changed, 140 insertions(+)
>> create mode 100644 drivers/mux/sparx5-spi.c
>>
>> diff --git a/drivers/mux/Makefile b/drivers/mux/Makefile
>> index 6e9fa47daf566..18c3ae3582ece 100644
>> --- a/drivers/mux/Makefile
>> +++ b/drivers/mux/Makefile
>> @@ -8,9 +8,11 @@ mux-adg792a-objs := adg792a.o
>> mux-adgs1408-objs := adgs1408.o
>> mux-gpio-objs := gpio.o
>> mux-mmio-objs := mmio.o
>> +mux-sparx5-objs := sparx5-spi.o
>>
>> obj-$(CONFIG_MULTIPLEXER) += mux-core.o
>> obj-$(CONFIG_MUX_ADG792A) += mux-adg792a.o
>> obj-$(CONFIG_MUX_ADGS1408) += mux-adgs1408.o
>> obj-$(CONFIG_MUX_GPIO) += mux-gpio.o
>> obj-$(CONFIG_MUX_MMIO) += mux-mmio.o
>> +obj-$(CONFIG_SPI_DW_MMIO) += mux-sparx5.o
>> diff --git a/drivers/mux/sparx5-spi.c b/drivers/mux/sparx5-spi.c
>> new file mode 100644
>> index 0000000000000..5fe9025b96a5e
>> --- /dev/null
>> +++ b/drivers/mux/sparx5-spi.c
>> @@ -0,0 +1,138 @@
>> +// SPDX-License-Identifier: GPL-2.0
>> +/*
>> + * Sparx5 SPI MUX driver
>> + *
>> + * Copyright (c) 2019 Microsemi Corporation
>> + *
>> + * Author: Lars Povlsen <lars.povlsen at microchip.com>
>> + */
>> +
>> +#include <linux/err.h>
>> +#include <linux/module.h>
>> +#include <linux/mux/driver.h>
>> +#include <linux/of_platform.h>
>> +#include <linux/platform_device.h>
>> +#include <linux/property.h>
>> +#include <linux/mux/driver.h>
>> +#include <linux/mfd/syscon.h>
>> +#include <linux/regmap.h>
>> +#include <linux/bitfield.h>
>> +
>> +#define MSCC_IF_SI_OWNER_SISL 0
>> +#define MSCC_IF_SI_OWNER_SIBM 1
>> +#define MSCC_IF_SI_OWNER_SIMC 2
>> +
>> +#define SPARX5_CPU_SYSTEM_CTRL_GENERAL_CTRL 0x88
>> +#define SPARX5_IF_SI_OWNER GENMASK(7, 6)
>> +#define SPARX5_IF_SI2_OWNER GENMASK(5, 4)
>> +
>> +#define SPARX5_MAX_CS 16
>> +
>> +struct mux_sparx5 {
>> + struct regmap *syscon;
>> + u8 bus[SPARX5_MAX_CS];
>> + int cur_bus;
>
> Surplus unused variable?
>
>> +};
>> +
>> +/*
>> + * Set the owner of the SPI interfaces
>> + */
>> +static void mux_sparx5_set_owner(struct regmap *syscon,
>> + u8 owner, u8 owner2)
>> +{
>> + u32 val, msk;
>> +
>> + val = FIELD_PREP(SPARX5_IF_SI_OWNER, owner) |
>> + FIELD_PREP(SPARX5_IF_SI2_OWNER, owner2);
>> + msk = SPARX5_IF_SI_OWNER | SPARX5_IF_SI2_OWNER;
>> + regmap_update_bits(syscon,
>> + SPARX5_CPU_SYSTEM_CTRL_GENERAL_CTRL,
>> + msk, val);
>> +}
>> +
>> +static void mux_sparx5_set_cs_owner(struct mux_sparx5 *mux_sparx5,
>> + u8 cs, u8 owner)
>> +{
>> + u8 other = (owner == MSCC_IF_SI_OWNER_SIBM ?
>> + MSCC_IF_SI_OWNER_SIMC : MSCC_IF_SI_OWNER_SIBM);
>
> Empty line missing here.
>
>> + if (mux_sparx5->bus[cs])
>> + /* SPI2 */
>> + mux_sparx5_set_owner(mux_sparx5->syscon, other, owner);
>> + else
>> + /* SPI1 */
>> + mux_sparx5_set_owner(mux_sparx5->syscon, owner, other);
>> +}
>
>
> This smells like there are only two states for this mux control, and that
> the whole point of this driver is to make the exact numbering selectable.
> I don't see the point of that. To me, it looks like the pre-existing
> mmio-mux should be able to work. Something like this? Untested of course,
> and I might easily have misunderstood something...
>
Peter,
Good suggestion with "mmio-mux" - I overlooked it actually supports
regmap. It makes DT configuration a little less intuitive, but removes
the baggage of the dedicated sparx5 mux driver and bindings.
It also pushes the solution towards using "spi-mux", but at least the CS
in the DT does not have to be repeated.
So a little more DT stuff, but less new code.
I will try to implement the "mmio-mux"/"spi-mux" solution in a rev4.
Any comments from Mark?
Anyway, Peter, thank you for your comments.
(Your driver comments are all valid, but it appears the driver isn't
needed after all)
Cheers,
---Lars
> mux: mux-controller {
> compatible = "mmio-mux"
> #mux-control-cells = <1>;
>
> /* SI_OWNER and SI2_OWNER in GENERAL_CTRL */
> mux-reg-masks = <0x88 0xf0>;
> };
>
>
> spi0: spi at 600104000 {
> compatible = "microchip,sparx5-spi";
> spi at 0 {
> compatible = "spi-mux";
> mux-controls = <&mux 0>;
> reg = <0>;
> /* SI_OWNER = SIMC, SI2_OWNER = SIBM ---> mux value 9 */
> spi-flash at 9 {
> compatible = "jedec,spi-nor";
> reg = <9>;
> };
> };
> spi at e {
> compatible = "spi-mux";
> mux-controls = <&mux 0>;
> reg = <14>;
> /* SI_OWNER = SIBM, SI2_OWNER = SIMC ---> mux value 6 */
> spi-flash at 6 {
> compatible = "spi-nand";
> reg = <6>;
> };
> };
> };
>
>> +
>> +static int mux_sparx5_set(struct mux_control *mux, int state)
>> +{
>> + struct mux_sparx5 *mux_sparx5 = mux_chip_priv(mux->chip);
>> +
>> + mux_sparx5_set_cs_owner(mux_sparx5, state, MSCC_IF_SI_OWNER_SIMC);
>> +
>> + return 0;
>> +}
>> +
>> +static const struct mux_control_ops mux_sparx5_ops = {
>> + .set = mux_sparx5_set,
>> +};
>> +
>> +static const struct of_device_id mux_sparx5_dt_ids[] = {
>> + { .compatible = "microchip,sparx5-spi-mux", },
>> + { /* sentinel */ }
>> +};
>> +MODULE_DEVICE_TABLE(of, mux_sparx5_dt_ids);
>> +
>> +static int mux_sparx5_probe(struct platform_device *pdev)
>> +{
>> + struct device *dev = &pdev->dev;
>> + struct mux_chip *mux_chip;
>> + struct mux_sparx5 *mux_sparx5;
>> + struct device_node *nc;
>> + const char *syscon_name = "microchip,sparx5-cpu-syscon";
>> + int ret;
>> +
>> + mux_chip = devm_mux_chip_alloc(dev, 1, sizeof(*mux_sparx5));
>> + if (IS_ERR(mux_chip))
>> + return PTR_ERR(mux_chip);
>> +
>> + mux_sparx5 = mux_chip_priv(mux_chip);
>> + mux_chip->ops = &mux_sparx5_ops;
>> +
>> + mux_sparx5->syscon =
>> + syscon_regmap_lookup_by_compatible(syscon_name);
>> + if (IS_ERR(mux_sparx5->syscon)) {
>> + dev_err(dev, "No syscon map %s\n", syscon_name);
>> + return PTR_ERR(mux_sparx5->syscon);
>> + }
>> +
>> + /* Get bus interface mapping */
>> + for_each_available_child_of_node(dev->of_node, nc) {
>> + u32 cs, bus;
>> +
>> + if (of_property_read_u32(nc, "reg", &cs) == 0 &&
>> + cs < SPARX5_MAX_CS &&
>> + of_property_read_u32(nc, "microchip,bus-interface",
>> + &bus) == 0)
>> + mux_sparx5->bus[cs] = bus;
>
> The above if is a mess. The kernel model is to handle the exceptional cases
> first and break/goto/continue/return/whatever so that the interesting code
> can happen at lower indentation level.
>
> if (of_property_read_u32(nc, "reg", &cs))
> continue;
> if (cs >= SPARX5_MAX_CS)
> continue;
> if (of_property_read_u32(nc, "microchip,bus-interface", &bus))
> continue;
>
> mux_sparc5->bus[cs] = bus;
>
> Cheers,
> Peter
>
>> + }
>> +
>> + mux_chip->mux->states = SPARX5_MAX_CS;
>> +
>> + ret = devm_mux_chip_register(dev, mux_chip);
>> + if (ret < 0)
>> + return ret;
>> +
>> + dev_info(dev, "%u-way mux-controller registered\n",
>> + mux_chip->mux->states);
>> +
>> + return 0;
>> +}
>> +
>> +static struct platform_driver mux_sparx5_driver = {
>> + .driver = {
>> + .name = "sparx5-mux",
>> + .of_match_table = of_match_ptr(mux_sparx5_dt_ids),
>> + },
>> + .probe = mux_sparx5_probe,
>> +};
>> +module_platform_driver(mux_sparx5_driver);
>>
--
Lars Povlsen,
Microchip
More information about the linux-arm-kernel
mailing list