[PATCH v3] ARM: dts: mvebu: add support for SolidRun Clearfog GTR

Gregory CLEMENT gregory.clement at bootlin.com
Wed Jan 8 01:54:21 PST 2020


Hi Baruch,

> SolidRun Clearfog GTR L8 and S4 SBCs are based on Armada 385. They
> features 8 (L8) or 4 (S4) switched Ethernet ports, 1 1Gb Ethernet port,
> 1 directly connected SFP port, 1 SFP port behind the switch (not
> currently described in DT), 3 mini-PCIe slots, eMMC, SPI flash, USB3
> port.
>
>   https://developer.solid-run.com/products/clearfog-gtr-a385/
>
> Reviewed-by: Andrew Lunn <andrew at lunn.ch>
> Signed-off-by: Baruch Siach <baruch at tkos.co.il>

Applied on mvebu/dt

However I wonder why you didn't use the alias for rtc, i2c, sdhci, usb
and pcie while you use aliases for the other nodes.

Thanks,

Gregory

> ---
> v3:
>   Set top 'model' property in .dts per-board (Josua Mayer)
>
> v2:
>   * Add 'regulator-always-on' to USB regulator
>
>   Address Andrew Lunn's comments:
>   * Extend the comment on I2C bus SFP target
>   * Rename SFP node label to 'sfp0'
>   * Use common leds function binding
>   * Add a comment on the sample at reset isolator
> ---
>  arch/arm/boot/dts/Makefile                    |   2 +
>  .../boot/dts/armada-385-clearfog-gtr-l8.dts   | 115 +++++
>  .../boot/dts/armada-385-clearfog-gtr-s4.dts   |  79 +++
>  .../arm/boot/dts/armada-385-clearfog-gtr.dtsi | 450 ++++++++++++++++++
>  4 files changed, 646 insertions(+)
>  create mode 100644 arch/arm/boot/dts/armada-385-clearfog-gtr-l8.dts
>  create mode 100644 arch/arm/boot/dts/armada-385-clearfog-gtr-s4.dts
>  create mode 100644 arch/arm/boot/dts/armada-385-clearfog-gtr.dtsi
>
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index 08011dc8c7a6..eb5add0f0f05 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -1238,6 +1238,8 @@ dtb-$(CONFIG_MACH_ARMADA_370) += \
>  dtb-$(CONFIG_MACH_ARMADA_375) += \
>  	armada-375-db.dtb
>  dtb-$(CONFIG_MACH_ARMADA_38X) += \
> +	armada-385-clearfog-gtr-s4.dtb \
> +	armada-385-clearfog-gtr-l8.dtb \
>  	armada-385-db-88f6820-amc.dtb \
>  	armada-385-db-ap.dtb \
>  	armada-385-linksys-caiman.dtb \
> diff --git a/arch/arm/boot/dts/armada-385-clearfog-gtr-l8.dts b/arch/arm/boot/dts/armada-385-clearfog-gtr-l8.dts
> new file mode 100644
> index 000000000000..c9ac630e5874
> --- /dev/null
> +++ b/arch/arm/boot/dts/armada-385-clearfog-gtr-l8.dts
> @@ -0,0 +1,115 @@
> +// SPDX-License-Identifier: (GPL-2.0 OR MIT)
> +
> +#include "armada-385-clearfog-gtr.dtsi"
> +
> +/ {
> +	model = "SolidRun Clearfog GTR L8";
> +};
> +
> +&mdio {
> +	switch0: switch0 at 4 {
> +		compatible = "marvell,mv88e6190";
> +		reg = <4>;
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&cf_gtr_switch_reset_pins>;
> +		reset-gpios = <&gpio0 18 GPIO_ACTIVE_LOW>;
> +
> +		ports {
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +
> +			port at 1 {
> +				reg = <1>;
> +				label = "lan8";
> +				phy-handle = <&switch0phy0>;
> +			};
> +
> +			port at 2 {
> +				reg = <2>;
> +				label = "lan7";
> +				phy-handle = <&switch0phy1>;
> +			};
> +
> +			port at 3 {
> +				reg = <3>;
> +				label = "lan6";
> +				phy-handle = <&switch0phy2>;
> +			};
> +
> +			port at 4 {
> +				reg = <4>;
> +				label = "lan5";
> +				phy-handle = <&switch0phy3>;
> +			};
> +
> +			port at 5 {
> +				reg = <5>;
> +				label = "lan4";
> +				phy-handle = <&switch0phy4>;
> +			};
> +
> +			port at 6 {
> +				reg = <6>;
> +				label = "lan3";
> +				phy-handle = <&switch0phy5>;
> +			};
> +
> +			port at 7 {
> +				reg = <7>;
> +				label = "lan2";
> +				phy-handle = <&switch0phy6>;
> +			};
> +
> +			port at 8 {
> +				reg = <8>;
> +				label = "lan1";
> +				phy-handle = <&switch0phy7>;
> +			};
> +
> +			port at 10 {
> +				reg = <10>;
> +				label = "cpu";
> +				ethernet = <&eth1>;
> +			};
> +
> +		};
> +
> +		mdio {
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +
> +			switch0phy0: switch0phy0 at 1 {
> +				reg = <0x1>;
> +			};
> +
> +			switch0phy1: switch0phy1 at 2 {
> +				reg = <0x2>;
> +			};
> +
> +			switch0phy2: switch0phy2 at 3 {
> +				reg = <0x3>;
> +			};
> +
> +			switch0phy3: switch0phy3 at 4 {
> +				reg = <0x4>;
> +			};
> +
> +			switch0phy4: switch0phy4 at 5 {
> +				reg = <0x5>;
> +			};
> +
> +			switch0phy5: switch0phy5 at 6 {
> +				reg = <0x6>;
> +			};
> +
> +			switch0phy6: switch0phy6 at 7 {
> +				reg = <0x7>;
> +			};
> +
> +			switch0phy7: switch0phy7 at 8 {
> +				reg = <0x8>;
> +			};
> +		};
> +
> +	};
> +};
> diff --git a/arch/arm/boot/dts/armada-385-clearfog-gtr-s4.dts b/arch/arm/boot/dts/armada-385-clearfog-gtr-s4.dts
> new file mode 100644
> index 000000000000..fa653b379490
> --- /dev/null
> +++ b/arch/arm/boot/dts/armada-385-clearfog-gtr-s4.dts
> @@ -0,0 +1,79 @@
> +// SPDX-License-Identifier: (GPL-2.0 OR MIT)
> +
> +#include "armada-385-clearfog-gtr.dtsi"
> +
> +/ {
> +	model = "SolidRun Clearfog GTR S4";
> +};
> +
> +&sfp0 {
> +	tx-fault-gpio = <&gpio0 24 GPIO_ACTIVE_HIGH>;
> +};
> +
> +&mdio {
> +	switch0: switch0 at 4 {
> +		compatible = "marvell,mv88e6085";
> +		reg = <4>;
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&cf_gtr_switch_reset_pins>;
> +		reset-gpios = <&gpio0 18 GPIO_ACTIVE_LOW>;
> +
> +		ports {
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +
> +			port at 1 {
> +				reg = <1>;
> +				label = "lan2";
> +				phy-handle = <&switch0phy0>;
> +			};
> +
> +			port at 2 {
> +				reg = <2>;
> +				label = "lan1";
> +				phy-handle = <&switch0phy1>;
> +			};
> +
> +			port at 3 {
> +				reg = <3>;
> +				label = "lan4";
> +				phy-handle = <&switch0phy2>;
> +			};
> +
> +			port at 4 {
> +				reg = <4>;
> +				label = "lan3";
> +				phy-handle = <&switch0phy3>;
> +			};
> +
> +			port at 5 {
> +				reg = <5>;
> +				label = "cpu";
> +				ethernet = <&eth1>;
> +			};
> +
> +		};
> +
> +		mdio {
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +
> +			switch0phy0: switch0phy0 at 11 {
> +				reg = <0x11>;
> +			};
> +
> +			switch0phy1: switch0phy1 at 12 {
> +				reg = <0x12>;
> +			};
> +
> +			switch0phy2: switch0phy2 at 13 {
> +				reg = <0x13>;
> +			};
> +
> +			switch0phy3: switch0phy3 at 14 {
> +				reg = <0x14>;
> +			};
> +		};
> +
> +	};
> +};
> diff --git a/arch/arm/boot/dts/armada-385-clearfog-gtr.dtsi b/arch/arm/boot/dts/armada-385-clearfog-gtr.dtsi
> new file mode 100644
> index 000000000000..624bbcae68c0
> --- /dev/null
> +++ b/arch/arm/boot/dts/armada-385-clearfog-gtr.dtsi
> @@ -0,0 +1,450 @@
> +// SPDX-License-Identifier: (GPL-2.0 OR MIT)
> +/*
> + * Device Tree file for Clearfog GTR machines rev 1.0 (88F6825)
> + *
> + *  Rabeeh Khoury <rabeeh at solid-run.com>, based on Russell King clearfog work
> + */
> +
> +/*
> +	SERDES mapping -
> +	0. SATA1 on CON18, or optionally mini PCIe CON3 - PCIe0
> +	1. 6141 switch (2.5Gbps capable)
> +	2. SATA0 on CON17, or optionally mini PCIe CON4 - PCIe1
> +	3. USB 3.0 Host
> +	4. mini PCIe CON2 - PCIe2
> +	5. SFP connector, or optionally SGMII Ethernet 1512 PHY
> +
> +	USB 2.0 mapping -
> +	0. USB 2.0 - 0 USB pins header CON12
> +	1. USB 2.0 - 1 mini PCIe CON2
> +	2. USB 2.0 - 2 to USB 3.0 connector (used with SERDES #3)
> +
> +	Pin mapping -
> +	0,1 - console UART
> +	2,3 - I2C0 - connected to I2C EEPROM, two temperature sensors,
> +	      front panel and PSE controller
> +	4,5 - MDC/MDIO
> +	6..17 - RGMII
> +	18 - Topaz switch reset (active low)
> +	19 - 1512 phy reset
> +	20 - 1512 phy reset (eth2, optional)
> +	21,28,37,38,39,40 - SD0
> +	22 - USB 3.0 current limiter enable (active high)
> +	24 - SFP TX fault (input active high)
> +	25 - SFP present (input active low)
> +	26,27 - I2C1 - connected to SFP
> +	29 - Fan PWM
> +	30 - CON4 mini PCIe wifi disable
> +	31 - CON3 mini PCIe wifi disable
> +	32 - Fuse programming power toggle (1.8v)
> +	33 - CON4 mini PCIe reset
> +	34 - CON2 mini PCIe wifi disable
> +	35 - CON3 mini PCIe reset
> +	36 - Rear button (GPIO active low)
> +	41 - CON1 front panel connector
> +	42 - Front LED1, or front panel CON1
> +	43 - Micron L-PBGA 24 ball SPI (1Gb) CS, or TPM SPI CS
> +	44 - CON2 mini PCIe reset
> +	45 - TPM PIRQ signal, or front panel CON1
> +	46 - SFP TX disable
> +	47 - Control isolation of boot sensitive SAR signals
> +	48 - PSE reset
> +	49 - PSE OSS signal
> +	50 - PSE interrupt
> +	52 - Front LED2, or front panel
> +	53 - Front button
> +	54 - SFP LOS (input active high)
> +	55 - Fan sense
> +	56(mosi),57(clk),58(miso) - SPI interface - 32Mb SPI, 1Gb SPI and TPM
> +	59 - SPI 32Mb W25Q32BVZPIG CS0 chip select (bootable)
> +*/
> +
> +/dts-v1/;
> +#include <dt-bindings/input/input.h>
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/leds/common.h>
> +#include "armada-385.dtsi"
> +
> +/ {
> +	compatible = "marvell,armada385", "marvell,armada380";
> +
> +	aliases {
> +		/* So that mvebu u-boot can update the MAC addresses */
> +		ethernet1 = &eth0;
> +		ethernet2 = &eth1;
> +		ethernet3 = &eth2;
> +		i2c0 = &i2c0;
> +		i2c1 = &i2c1;
> +	};
> +
> +	chosen {
> +		stdout-path = "serial0:115200n8";
> +	};
> +
> +	memory {
> +		device_type = "memory";
> +		reg = <0x00000000 0x10000000>; /* 256 MB */
> +	};
> +
> +	reg_3p3v: regulator-3p3v {
> +		compatible = "regulator-fixed";
> +		regulator-name = "3P3V";
> +		regulator-min-microvolt = <3300000>;
> +		regulator-max-microvolt = <3300000>;
> +		regulator-always-on;
> +	};
> +
> +	reg_5p0v: regulator-5p0v {
> +		compatible = "regulator-fixed";
> +		regulator-name = "5P0V";
> +		regulator-min-microvolt = <5000000>;
> +		regulator-max-microvolt = <5000000>;
> +		regulator-always-on;
> +	};
> +
> +	v_usb3_con: regulator-v-usb3-con {
> +		compatible = "regulator-fixed";
> +		gpio = <&gpio0 22 GPIO_ACTIVE_LOW>;
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&cf_gtr_usb3_con_vbus>;
> +		regulator-max-microvolt = <5000000>;
> +		regulator-min-microvolt = <5000000>;
> +		regulator-name = "v_usb3_con";
> +		vin-supply = <&reg_5p0v>;
> +		regulator-boot-on;
> +		regulator-always-on;
> +	};
> +
> +	soc {
> +		ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000
> +			  MBUS_ID(0x01, 0x1d) 0 0xfff00000 0x100000
> +			  MBUS_ID(0x09, 0x19) 0 0xf1100000 0x10000
> +			  MBUS_ID(0x09, 0x15) 0 0xf1110000 0x10000
> +			  MBUS_ID(0x0c, 0x04) 0 0xf1200000 0x100000>;
> +
> +		internal-regs {
> +
> +			rtc at a3800 {
> +				status = "okay";
> +			};
> +
> +			i2c at 11000 { /* ROM, temp sensor and front panel */
> +				pinctrl-0 = <&i2c0_pins>;
> +				pinctrl-names = "default";
> +				status = "okay";
> +			};
> +
> +			i2c at 11100 { /* SFP (CON5/CON6) */
> +				pinctrl-0 = <&cf_gtr_i2c1_pins>;
> +				pinctrl-names = "default";
> +				status = "okay";
> +			};
> +
> +			pinctrl at 18000 {
> +				cf_gtr_switch_reset_pins: cf-gtr-switch-reset-pins {
> +					marvell,pins = "mpp18";
> +					marvell,function = "gpio";
> +				};
> +
> +				cf_gtr_usb3_con_vbus: cf-gtr-usb3-con-vbus {
> +					marvell,pins = "mpp22";
> +					marvell,function = "gpio";
> +				};
> +
> +				cf_gtr_fan_pwm: cf-gtr-fan-pwm {
> +					marvell,pins = "mpp23";
> +					marvell,function = "gpio";
> +				};
> +
> +				cf_gtr_i2c1_pins: i2c1-pins {
> +					/* SFP */
> +					marvell,pins = "mpp26", "mpp27";
> +					marvell,function = "i2c1";
> +				};
> +
> +				cf_gtr_sdhci_pins: cf-gtr-sdhci-pins {
> +					marvell,pins = "mpp21", "mpp28",
> +						       "mpp37", "mpp38",
> +						       "mpp39", "mpp40";
> +					marvell,function = "sd0";
> +				};
> +
> +				cf_gtr_isolation_pins: cf-gtr-isolation-pins {
> +					marvell,pins = "mpp47";
> +					marvell,function = "gpio";
> +				};
> +
> +				cf_gtr_poe_reset_pins: cf-gtr-poe-reset-pins {
> +					marvell,pins = "mpp48";
> +					marvell,function = "gpio";
> +				};
> +
> +				cf_gtr_spi1_cs_pins: spi1-cs-pins {
> +					marvell,pins = "mpp59";
> +					marvell,function = "spi1";
> +				};
> +
> +				cf_gtr_front_button_pins: cf-gtr-front-button-pins {
> +					marvell,pins = "mpp53";
> +					marvell,function = "gpio";
> +				};
> +
> +				cf_gtr_rear_button_pins: cf-gtr-rear-button-pins {
> +					marvell,pins = "mpp36";
> +					marvell,function = "gpio";
> +				};
> +			};
> +
> +			sdhci at d8000 {
> +				bus-width = <4>;
> +				no-1-8-v;
> +				non-removable;
> +				pinctrl-0 = <&cf_gtr_sdhci_pins>;
> +				pinctrl-names = "default";
> +				status = "okay";
> +				vmmc = <&reg_3p3v>;
> +				wp-inverted;
> +			};
> +
> +			usb at 58000 {
> +				status = "okay";
> +			};
> +
> +			usb3 at f0000 {
> +				status = "okay";
> +			};
> +
> +			usb3 at f8000 {
> +				vbus-supply = <&v_usb3_con>;
> +				status = "okay";
> +			};
> +		};
> +
> +		pcie {
> +			status = "okay";
> +			/*
> +			 * The PCIe units are accessible through
> +			 * the mini-PCIe connectors on the board.
> +			 */
> +			pcie at 1,0 {
> +				reset-gpios = <&gpio1 3 GPIO_ACTIVE_LOW>;
> +				status = "okay";
> +			};
> +
> +			pcie at 2,0 {
> +				reset-gpios = <&gpio1 1 GPIO_ACTIVE_LOW>;
> +				status = "okay";
> +			};
> +
> +			pcie at 3,0 {
> +				reset-gpios = <&gpio1 12 GPIO_ACTIVE_LOW>;
> +				status = "okay";
> +			};
> +		};
> +	};
> +
> +	sfp0: sfp {
> +		compatible = "sff,sfp";
> +		i2c-bus = <&i2c1>;
> +		los-gpio = <&gpio1 22 GPIO_ACTIVE_HIGH>;
> +		mod-def0-gpio = <&gpio0 25 GPIO_ACTIVE_LOW>;
> +		tx-disable-gpio = <&gpio1 14 GPIO_ACTIVE_HIGH>;
> +	};
> +
> +	gpio-keys {
> +		compatible = "gpio-keys";
> +		pinctrl-0 = <&cf_gtr_rear_button_pins &cf_gtr_front_button_pins>;
> +		pinctrl-names = "default";
> +
> +		button_0 {
> +			label = "Rear Button";
> +			gpios = <&gpio1 4 GPIO_ACTIVE_LOW>;
> +			linux,can-disable;
> +			linux,code = <BTN_0>;
> +		};
> +
> +		button_1 {
> +			label = "Front Button";
> +			gpios = <&gpio1 21 GPIO_ACTIVE_LOW>;
> +			linux,can-disable;
> +			linux,code = <BTN_1>;
> +		};
> +	};
> +
> +	gpio-leds {
> +		compatible = "gpio-leds";
> +
> +		led1 {
> +			function = LED_FUNCTION_CPU;
> +			color = <LED_COLOR_ID_GREEN>;
> +			gpios = <&gpio1 10 GPIO_ACTIVE_HIGH>;
> +		};
> +
> +		led2 {
> +			function = LED_FUNCTION_HEARTBEAT;
> +			color = <LED_COLOR_ID_GREEN>;
> +			gpios = <&gpio1 20 GPIO_ACTIVE_HIGH>;
> +		};
> +	};
> +};
> +
> +&bm {
> +	status = "okay";
> +};
> +
> +&bm_bppi {
> +	status = "okay";
> +};
> +
> +&eth0 {
> +	/* ethernet at 70000 */
> +	pinctrl-0 = <&ge0_rgmii_pins>;
> +	pinctrl-names = "default";
> +	phy = <&phy_dedicated>;
> +	phy-mode = "rgmii-id";
> +	buffer-manager = <&bm>;
> +	bm,pool-long = <0>;
> +	bm,pool-short = <1>;
> +	status = "okay";
> +};
> +
> +&eth1 {
> +	/* ethernet at 30000 */
> +	bm,pool-long = <2>;
> +	bm,pool-short = <1>;
> +	buffer-manager = <&bm>;
> +	phys = <&comphy1 1>;
> +	phy-mode = "2500base-x";
> +	status = "okay";
> +
> +	fixed-link {
> +		speed = <2500>;
> +		full-duplex;
> +	};
> +};
> +
> +&eth2 {
> +	/* ethernet at 34000 */
> +	bm,pool-long = <3>;
> +	bm,pool-short = <1>;
> +	buffer-manager = <&bm>;
> +	managed = "in-band-status";
> +	phys = <&comphy5 1>;
> +	phy-mode = "sgmii";
> +	sfp = <&sfp0>;
> +	status = "okay";
> +};
> +
> +&mdio {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&mdio_pins>;
> +	status = "okay";
> +
> +	phy_dedicated: ethernet-phy at 0 {
> +		/*
> +		 * Annoyingly, the marvell phy driver configures the LED
> +		 * register, rather than preserving reset-loaded setting.
> +		 * We undo that rubbish here.
> +		 */
> +		marvell,reg-init = <3 16 0 0x1017>;
> +		reg = <0>;
> +	};
> +};
> +
> +&uart0 {
> +	pinctrl-0 = <&uart0_pins>;
> +	pinctrl-names = "default";
> +	status = "okay";
> +};
> +
> +&spi1 {
> +	/*
> +	 * CS0: W25Q32 flash
> +	 */
> +	pinctrl-0 = <&spi1_pins &cf_gtr_spi1_cs_pins>;
> +	pinctrl-names = "default";
> +	status = "okay";
> +
> +	spi-flash at 0 {
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +		compatible = "w25q32", "jedec,spi-nor";
> +		reg = <0>; /* Chip select 0 */
> +		spi-max-frequency = <3000000>;
> +		status = "okay";
> +	};
> +};
> +
> +&i2c0 {
> +	pinctrl-0 = <&i2c0_pins>;
> +	pinctrl-names = "default";
> +	status = "okay";
> +
> +	/* U26 temperature sensor placed near SoC */
> +	temp1: nct75 at 4c {
> +		compatible = "lm75";
> +		reg = <0x4c>;
> +	};
> +
> +	/* U27 temperature sensor placed near RTC battery */
> +	temp2: nct75 at 4d {
> +		compatible = "lm75";
> +		reg = <0x4d>;
> +	};
> +
> +	/* 2Kb eeprom */
> +	eeprom at 53 {
> +		compatible = "atmel,24c02";
> +		reg = <0x53>;
> +	};
> +};
> +
> +&ahci0 {
> +	status = "okay";
> +};
> +
> +&ahci1 {
> +	status = "okay";
> +};
> +
> +&gpio0 {
> +	pinctrl-0 = <&cf_gtr_fan_pwm>;
> +	pinctrl-names = "default";
> +
> +	wifi-disable {
> +		gpio-hog;
> +		gpios = <30 GPIO_ACTIVE_LOW>, <31 GPIO_ACTIVE_LOW>;
> +		output-low;
> +		line-name = "wifi-disable";
> +	};
> +};
> +
> +&gpio1 {
> +	pinctrl-0 = <&cf_gtr_isolation_pins &cf_gtr_poe_reset_pins>;
> +	pinctrl-names = "default";
> +
> +	lte-disable {
> +		gpio-hog;
> +		gpios = <2 GPIO_ACTIVE_LOW>;
> +		output-low;
> +		line-name = "lte-disable";
> +	};
> +
> +	/*
> +	 * This signal, when asserted, isolates Armada 38x sample at reset pins
> +	 * from control of external devices. Should be de-asserted after reset.
> +	 */
> +	sar-isolation {
> +		gpio-hog;
> +		gpios = <15 GPIO_ACTIVE_LOW>;
> +		output-low;
> +		line-name = "sar-isolation";
> +	};
> +
> +	poe-reset {
> +		gpio-hog;
> +		gpios = <16 GPIO_ACTIVE_LOW>;
> +		output-low;
> +		line-name = "poe-reset";
> +	};
> +};
> -- 
> 2.24.1
>

-- 
Gregory Clement, Bootlin
Embedded Linux and Kernel engineering
http://bootlin.com



More information about the linux-arm-kernel mailing list