[PATCH v4 00/15] Allwinner MIPI CSI-2 support for A31/V3s/A83T
Paul Kocialkowski
paul.kocialkowski at bootlin.com
Thu Dec 31 09:29:33 EST 2020
This series introduces support for MIPI CSI-2, with the A31 controller that is
found on most SoCs (A31, V3s and probably V5) as well as the A83T-specific
controller. While the former uses the same MIPI D-PHY that is already supported
for DSI, the latter embeds its own D-PHY.
In order to distinguish the use of the D-PHY between Rx mode (for MIPI CSI-2)
and Tx mode (for MIPI DSI), a submode is introduced for D-PHY in the PHY API.
This allows adding Rx support in the A31 D-PHY driver.
A few changes and fixes are applied to the A31 CSI controller driver, in order
to support the MIPI CSI-2 use-case.
Changes since v3:
- Fixed single-item phys description in sun6i mipi csi-2 binding;
- Fixed variables names in macros using container_of;
- Fixed style issue with operators at the end of lines;
- Reworked source endpoint/subdev assignment in sun6i-csi to handle
link_validate error case;
- Removed unrelated dt change in sun8i-a83t mipi csi-2 driver;
- Added collected tags.
Changes since v2:
- added Kconfig depend on PM since it's not optional;
- removed phy-names for A31 MIPI CSI-2 controller;
- removed v3s compatible in the A31 MIPI CSI-2 controller driver;
- removed A31 CSI controller single-port binding deprecation;
- removed empty dt port definitions;
- fixed minor checkpatch warnings;
- added collected tags;
- added media-ctl output in cover letter.
Changes since v1:
- reworked fwnode and media graph on the CSI controller end to have one port
per interface, which solves the bus type representation issue;
- removed unused IRQ handlers in the MIPI CSI-2 bridges;
- avoided the use of devm_regmap_init_mmio_clk;
- deasserted reset before enabling clocks;
- fixed reported return code issues (ret |=, missing checks);
- applied requested cosmetic changes (backward goto, etc);
- switched over to runtime PM for the mipi csi-2 bridge drivers;
- selected PHY_SUN6I_MIPI_DPHY in Kconfig for sun6i-mipi-csi2;
- registered nodes with mipi csi-2 bridge subdevs;
- used V4L2 format info instead of switch/case for sun6i-csi bpp;
- fixed device-tree bindings as requested (useless properties, license);
- fixed mipi bridge dt instances names;
- added PHY API documentation about mode/power on order requirement;
- fixed clock error return code in d-phy code;
- fixed D-PHY mode check in d-phy code;
- added MAINTAINERS entries for the new drivers;
- added V4L2 compliance results;
- added various comments and rework commit mesages as requested.
Media ctl outputs for the testing setups are available below:
# sun6i-csi + sun6i-mipi-csi2 + ov5648
Media device information
------------------------
driver sun6i-csi
model Allwinner Video Capture Device
serial
bus info platform:1cb0000.camera
hw revision 0x0
driver version 5.10.0
Device topology
- entity 1: sun6i-csi (2 pads, 1 link)
type Node subtype V4L flags 0
device node name /dev/video0
pad0: Sink
pad1: Sink
<- "sun6i-mipi-csi2":1 [ENABLED]
- entity 6: sun6i-mipi-csi2 (2 pads, 2 links)
type V4L2 subdev subtype Unknown flags 0
device node name /dev/v4l-subdev0
pad0: Sink
[fmt:unknown/0x0]
<- "ov5648 0-0036":0 [ENABLED,IMMUTABLE]
pad1: Source
[fmt:unknown/0x0]
-> "sun6i-csi":1 [ENABLED]
- entity 9: ov5648 0-0036 (1 pad, 1 link)
type V4L2 subdev subtype Sensor flags 0
device node name /dev/v4l-subdev1
pad0: Source
[fmt:SBGGR8_1X8/2592x1944 at 1/15 field:none colorspace:raw xfer:none ycbcr:601 quantization:full-range]
-> "sun6i-mipi-csi2":0 [ENABLED,IMMUTABLE]
# sun6i-csi + sun8i-a83t-mipi-csi2 + ov8865
Media device information
------------------------
driver sun6i-csi
model Allwinner Video Capture Device
serial
bus info platform:1cb0000.camera
hw revision 0x0
driver version 5.10.0
Device topology
- entity 1: sun6i-csi (2 pads, 1 link)
type Node subtype V4L flags 0
device node name /dev/video0
pad0: Sink
pad1: Sink
<- "sun8i-a83t-mipi-csi2":1 [ENABLED]
- entity 6: sun8i-a83t-mipi-csi2 (2 pads, 2 links)
type V4L2 subdev subtype Unknown flags 0
device node name /dev/v4l-subdev0
pad0: Sink
[fmt:unknown/0x0]
<- "ov8865 1-0036":0 [ENABLED,IMMUTABLE]
pad1: Source
[fmt:unknown/0x0]
-> "sun6i-csi":1 [ENABLED]
- entity 9: ov8865 1-0036 (1 pad, 1 link)
type V4L2 subdev subtype Sensor flags 0
device node name /dev/v4l-subdev1
pad0: Source
[fmt:SBGGR10_1X10/3264x2448 at 1/30 field:none colorspace:raw xfer:none ycbcr:601 quantization:full-range]
-> "sun8i-a83t-mipi-csi2":0 [ENABLED,IMMUTABLE]
V4L2 compliance runs are available below:
# sun6i-csi + sun6i-mipi-csi2 + ov5648
v4l2-compliance SHA: not available, 32 bits
Compliance test for sun6i-video device /dev/video0:
Driver Info:
Driver name : sun6i-video
Card type : sun6i-csi
Bus info : platform:camera
Driver version : 5.10.0
Capabilities : 0x84200001
Video Capture
Streaming
Extended Pix Format
Device Capabilities
Device Caps : 0x04200001
Video Capture
Streaming
Extended Pix Format
Media Driver Info:
Driver name : sun6i-csi
Model : Allwinner Video Capture Device
Serial :
Bus info : platform:1cb0000.camera
Media version : 5.10.0
Hardware revision: 0x00000000 (0)
Driver version : 5.10.0
Interface Info:
ID : 0x03000004
Type : V4L Video
Entity Info:
ID : 0x00000001 (1)
Name : sun6i-csi
Function : V4L2 I/O
Pad 0x01000002 : 0: Sink
Pad 0x01000003 : 1: Sink
Link 0x0200000d: from remote pad 0x1000008 of entity 'sun6i-mipi-csi2': Data, Enabled
Required ioctls:
test MC information (see 'Media Driver Info' above): OK
warn: v4l2-compliance.cpp(633): media bus_info 'platform:1cb0000.camera' differs from V4L2 bus_info 'platform:camera'
test VIDIOC_QUERYCAP: OK
Allow for multiple opens:
test second /dev/video0 open: OK
warn: v4l2-compliance.cpp(633): media bus_info 'platform:1cb0000.camera' differs from V4L2 bus_info 'platform:camera'
test VIDIOC_QUERYCAP: OK
test VIDIOC_G/S_PRIORITY: OK
test for unlimited opens: OK
Debug ioctls:
test VIDIOC_DBG_G/S_REGISTER: OK (Not Supported)
test VIDIOC_LOG_STATUS: OK
Input ioctls:
test VIDIOC_G/S_TUNER/ENUM_FREQ_BANDS: OK (Not Supported)
test VIDIOC_G/S_FREQUENCY: OK (Not Supported)
test VIDIOC_S_HW_FREQ_SEEK: OK (Not Supported)
test VIDIOC_ENUMAUDIO: OK (Not Supported)
test VIDIOC_G/S/ENUMINPUT: OK
test VIDIOC_G/S_AUDIO: OK (Not Supported)
Inputs: 1 Audio Inputs: 0 Tuners: 0
Output ioctls:
test VIDIOC_G/S_MODULATOR: OK (Not Supported)
test VIDIOC_G/S_FREQUENCY: OK (Not Supported)
test VIDIOC_ENUMAUDOUT: OK (Not Supported)
test VIDIOC_G/S/ENUMOUTPUT: OK (Not Supported)
test VIDIOC_G/S_AUDOUT: OK (Not Supported)
Outputs: 0 Audio Outputs: 0 Modulators: 0
Input/Output configuration ioctls:
test VIDIOC_ENUM/G/S/QUERY_STD: OK (Not Supported)
test VIDIOC_ENUM/G/S/QUERY_DV_TIMINGS: OK (Not Supported)
test VIDIOC_DV_TIMINGS_CAP: OK (Not Supported)
test VIDIOC_G/S_EDID: OK (Not Supported)
Control ioctls (Input 0):
warn: v4l2-test-controls.cpp(92): Exposure: (max - min) % step != 0
warn: v4l2-test-controls.cpp(92): Gain: (max - min) % step != 0
warn: v4l2-test-controls.cpp(92): Exposure: (max - min) % step != 0
warn: v4l2-test-controls.cpp(92): Gain: (max - min) % step != 0
test VIDIOC_QUERY_EXT_CTRL/QUERYMENU: OK
test VIDIOC_QUERYCTRL: OK
warn: v4l2-test-controls.cpp(368): Gain: returned control value 44 not a multiple of step
warn: v4l2-test-controls.cpp(368): Gain: returned control value 44 not a multiple of step
warn: v4l2-test-controls.cpp(368): Gain: returned control value 44 not a multiple of step
warn: v4l2-test-controls.cpp(368): Gain: returned control value 44 not a multiple of step
test VIDIOC_G/S_CTRL: OK
warn: v4l2-test-controls.cpp(555): Gain: returned control value 44 not a multiple of step
test VIDIOC_G/S/TRY_EXT_CTRLS: OK
test VIDIOC_(UN)SUBSCRIBE_EVENT/DQEVENT: OK
test VIDIOC_G/S_JPEGCOMP: OK (Not Supported)
Standard Controls: 15 Private Controls: 0
Format ioctls (Input 0):
test VIDIOC_ENUM_FMT/FRAMESIZES/FRAMEINTERVALS: OK
test VIDIOC_G/S_PARM: OK (Not Supported)
test VIDIOC_G_FBUF: OK (Not Supported)
test VIDIOC_G_FMT: OK
test VIDIOC_TRY_FMT: OK
test VIDIOC_S_FMT: OK
test VIDIOC_G_SLICED_VBI_CAP: OK (Not Supported)
test Cropping: OK (Not Supported)
test Composing: OK (Not Supported)
test Scaling: OK
Codec ioctls (Input 0):
test VIDIOC_(TRY_)ENCODER_CMD: OK (Not Supported)
test VIDIOC_G_ENC_INDEX: OK (Not Supported)
test VIDIOC_(TRY_)DECODER_CMD: OK (Not Supported)
Buffer ioctls (Input 0):
test VIDIOC_REQBUFS/CREATE_BUFS/QUERYBUF: OK
fail: v4l2-test-buffers.cpp(755): q.export_bufs(node, q.g_type())
test VIDIOC_EXPBUF: FAIL
test Requests: OK (Not Supported)
Total for sun6i-video device /dev/video0: 45, Succeeded: 44, Failed: 1, Warnings: 1
# sun6i-csi + sun8i-a83t-mipi-csi2 + ov8865
v4l2-compliance SHA: not available, 32 bits
Compliance test for sun6i-video device /dev/video0:
Driver Info:
Driver name : sun6i-video
Card type : sun6i-csi
Bus info : platform:camera
Driver version : 5.10.0
Capabilities : 0x84200001
Video Capture
Streaming
Extended Pix Format
Device Capabilities
Device Caps : 0x04200001
Video Capture
Streaming
Extended Pix Format
Media Driver Info:
Driver name : sun6i-csi
Model : Allwinner Video Capture Device
Serial :
Bus info : platform:1cb0000.camera
Media version : 5.10.0
Hardware revision: 0x00000000 (0)
Driver version : 5.10.0
Interface Info:
ID : 0x03000004
Type : V4L Video
Entity Info:
ID : 0x00000001 (1)
Name : sun6i-csi
Function : V4L2 I/O
Pad 0x01000002 : 0: Sink
Pad 0x01000003 : 1: Sink
Link 0x0200000d: from remote pad 0x1000008 of entity 'sun8i-a83t-mipi-csi2': Data, Enabled
Required ioctls:
test MC information (see 'Media Driver Info' above): OK
warn: v4l2-compliance.cpp(633): media bus_info 'platform:1cb0000.camera' differs from V4L2 bus_info 'platform:camera'
test VIDIOC_QUERYCAP: OK
Allow for multiple opens:
test second /dev/video0 open: OK
warn: v4l2-compliance.cpp(633): media bus_info 'platform:1cb0000.camera' differs from V4L2 bus_info 'platform:camera'
test VIDIOC_QUERYCAP: OK
test VIDIOC_G/S_PRIORITY: OK
test for unlimited opens: OK
Debug ioctls:
test VIDIOC_DBG_G/S_REGISTER: OK (Not Supported)
test VIDIOC_LOG_STATUS: OK
Input ioctls:
test VIDIOC_G/S_TUNER/ENUM_FREQ_BANDS: OK (Not Supported)
test VIDIOC_G/S_FREQUENCY: OK (Not Supported)
test VIDIOC_S_HW_FREQ_SEEK: OK (Not Supported)
test VIDIOC_ENUMAUDIO: OK (Not Supported)
test VIDIOC_G/S/ENUMINPUT: OK
test VIDIOC_G/S_AUDIO: OK (Not Supported)
Inputs: 1 Audio Inputs: 0 Tuners: 0
Output ioctls:
test VIDIOC_G/S_MODULATOR: OK (Not Supported)
test VIDIOC_G/S_FREQUENCY: OK (Not Supported)
test VIDIOC_ENUMAUDOUT: OK (Not Supported)
test VIDIOC_G/S/ENUMOUTPUT: OK (Not Supported)
test VIDIOC_G/S_AUDOUT: OK (Not Supported)
Outputs: 0 Audio Outputs: 0 Modulators: 0
Input/Output configuration ioctls:
test VIDIOC_ENUM/G/S/QUERY_STD: OK (Not Supported)
test VIDIOC_ENUM/G/S/QUERY_DV_TIMINGS: OK (Not Supported)
test VIDIOC_DV_TIMINGS_CAP: OK (Not Supported)
test VIDIOC_G/S_EDID: OK (Not Supported)
Control ioctls (Input 0):
warn: v4l2-test-controls.cpp(92): Exposure: (max - min) % step != 0
warn: v4l2-test-controls.cpp(92): Gain: (max - min) % step != 0
warn: v4l2-test-controls.cpp(92): Exposure: (max - min) % step != 0
warn: v4l2-test-controls.cpp(92): Gain: (max - min) % step != 0
test VIDIOC_QUERY_EXT_CTRL/QUERYMENU: OK
test VIDIOC_QUERYCTRL: OK
test VIDIOC_G/S_CTRL: OK
test VIDIOC_G/S/TRY_EXT_CTRLS: OK
test VIDIOC_(UN)SUBSCRIBE_EVENT/DQEVENT: OK
test VIDIOC_G/S_JPEGCOMP: OK (Not Supported)
Standard Controls: 11 Private Controls: 0
Format ioctls (Input 0):
test VIDIOC_ENUM_FMT/FRAMESIZES/FRAMEINTERVALS: OK
test VIDIOC_G/S_PARM: OK (Not Supported)
test VIDIOC_G_FBUF: OK (Not Supported)
test VIDIOC_G_FMT: OK
test VIDIOC_TRY_FMT: OK
test VIDIOC_S_FMT: OK
test VIDIOC_G_SLICED_VBI_CAP: OK (Not Supported)
test Cropping: OK (Not Supported)
test Composing: OK (Not Supported)
test Scaling: OK
Codec ioctls (Input 0):
test VIDIOC_(TRY_)ENCODER_CMD: OK (Not Supported)
test VIDIOC_G_ENC_INDEX: OK (Not Supported)
test VIDIOC_(TRY_)DECODER_CMD: OK (Not Supported)
Buffer ioctls (Input 0):
test VIDIOC_REQBUFS/CREATE_BUFS/QUERYBUF: OK
test VIDIOC_EXPBUF: OK
test Requests: OK (Not Supported)
Total for sun6i-video device /dev/video0: 45, Succeeded: 45, Failed: 0, Warnings: 6
Paul Kocialkowski (15):
docs: phy: Add a part about PHY mode and submode
phy: Distinguish between Rx and Tx for MIPI D-PHY with submodes
phy: allwinner: phy-sun6i-mipi-dphy: Support D-PHY Rx mode for MIPI
CSI-2
media: sun6i-csi: Use common V4L2 format info for storage bpp
media: sun6i-csi: Only configure the interface data width for parallel
dt-bindings: media: sun6i-a31-csi: Add MIPI CSI-2 input port
media: sun6i-csi: Add support for MIPI CSI-2 bridge input
dt-bindings: media: Add A31 MIPI CSI-2 bindings documentation
media: sunxi: Add support for the A31 MIPI CSI-2 controller
ARM: dts: sun8i: v3s: Add nodes for MIPI CSI-2 support
MAINTAINERS: Add entry for the Allwinner A31 MIPI CSI-2 bridge
dt-bindings: media: Add A83T MIPI CSI-2 bindings documentation
media: sunxi: Add support for the A83T MIPI CSI-2 controller
ARM: dts: sun8i: a83t: Add MIPI CSI-2 controller node
MAINTAINERS: Add entry for the Allwinner A83T MIPI CSI-2 bridge
.../media/allwinner,sun6i-a31-csi.yaml | 88 ++-
.../media/allwinner,sun6i-a31-mipi-csi2.yaml | 149 ++++
.../media/allwinner,sun8i-a83t-mipi-csi2.yaml | 147 ++++
Documentation/driver-api/phy/phy.rst | 18 +
MAINTAINERS | 16 +
arch/arm/boot/dts/sun8i-a83t.dtsi | 26 +
arch/arm/boot/dts/sun8i-v3s.dtsi | 67 ++
drivers/media/platform/sunxi/Kconfig | 2 +
drivers/media/platform/sunxi/Makefile | 2 +
.../platform/sunxi/sun6i-csi/sun6i_csi.c | 165 +++--
.../platform/sunxi/sun6i-csi/sun6i_csi.h | 64 +-
.../platform/sunxi/sun6i-csi/sun6i_video.c | 57 +-
.../platform/sunxi/sun6i-csi/sun6i_video.h | 7 +-
.../platform/sunxi/sun6i-mipi-csi2/Kconfig | 12 +
.../platform/sunxi/sun6i-mipi-csi2/Makefile | 4 +
.../sunxi/sun6i-mipi-csi2/sun6i_mipi_csi2.c | 590 ++++++++++++++++
.../sunxi/sun6i-mipi-csi2/sun6i_mipi_csi2.h | 117 ++++
.../sunxi/sun8i-a83t-mipi-csi2/Kconfig | 11 +
.../sunxi/sun8i-a83t-mipi-csi2/Makefile | 4 +
.../sun8i-a83t-mipi-csi2/sun8i_a83t_dphy.c | 92 +++
.../sun8i-a83t-mipi-csi2/sun8i_a83t_dphy.h | 39 ++
.../sun8i_a83t_mipi_csi2.c | 657 ++++++++++++++++++
.../sun8i_a83t_mipi_csi2.h | 197 ++++++
drivers/phy/allwinner/phy-sun6i-mipi-dphy.c | 164 ++++-
drivers/staging/media/rkisp1/rkisp1-isp.c | 3 +-
include/linux/phy/phy-mipi-dphy.h | 13 +
26 files changed, 2587 insertions(+), 124 deletions(-)
create mode 100644 Documentation/devicetree/bindings/media/allwinner,sun6i-a31-mipi-csi2.yaml
create mode 100644 Documentation/devicetree/bindings/media/allwinner,sun8i-a83t-mipi-csi2.yaml
create mode 100644 drivers/media/platform/sunxi/sun6i-mipi-csi2/Kconfig
create mode 100644 drivers/media/platform/sunxi/sun6i-mipi-csi2/Makefile
create mode 100644 drivers/media/platform/sunxi/sun6i-mipi-csi2/sun6i_mipi_csi2.c
create mode 100644 drivers/media/platform/sunxi/sun6i-mipi-csi2/sun6i_mipi_csi2.h
create mode 100644 drivers/media/platform/sunxi/sun8i-a83t-mipi-csi2/Kconfig
create mode 100644 drivers/media/platform/sunxi/sun8i-a83t-mipi-csi2/Makefile
create mode 100644 drivers/media/platform/sunxi/sun8i-a83t-mipi-csi2/sun8i_a83t_dphy.c
create mode 100644 drivers/media/platform/sunxi/sun8i-a83t-mipi-csi2/sun8i_a83t_dphy.h
create mode 100644 drivers/media/platform/sunxi/sun8i-a83t-mipi-csi2/sun8i_a83t_mipi_csi2.c
create mode 100644 drivers/media/platform/sunxi/sun8i-a83t-mipi-csi2/sun8i_a83t_mipi_csi2.h
--
2.29.2
More information about the linux-arm-kernel
mailing list