[PATCH] ARM: dts: stm32: Fix GPIO hog names on DHCOM

[Marek Vasut]

The GPIO hog node name should match regex '^(hog-[0-9]+|.+-hog(-[0-9]+)?)$',
make it so and fix the following two make dtbs_check warnings:

arch/arm/boot/dts/stm32mp157c-dhcom-picoitx.dt.yaml: hog-usb-port-power: $nodename:0: 'hog-usb-port-power' does not match '^(hog-[0-9]+|.+-hog(-[0-9]+)?)$'
arch/arm/boot/dts/stm32mp153c-dhcom-drc02.dt.yaml: hog-usb-hub: $nodename:0: 'hog-usb-hub' does not match '^(hog-[0-9]+|.+-hog(-[0-9]+)?)$'

Signed-off-by: Marek Vasut <marex at denx.de>
Cc: Alexandre Torgue <alexandre.torgue at st.com>
Cc: Maxime Coquelin <mcoquelin.stm32 at gmail.com>
Cc: Patrice Chotard <patrice.chotard at st.com>
Cc: Patrick Delaunay <patrick.delaunay at st.com>
Cc: linux-stm32 at st-md-mailman.stormreply.com
To: linux-arm-kernel at lists.infradead.org
---
 arch/arm/boot/dts/stm32mp15xx-dhcom-drc02.dtsi   | 4 ++--
 arch/arm/boot/dts/stm32mp15xx-dhcom-picoitx.dtsi | 2 +-
 2 files changed, 3 insertions(+), 3 deletions(-)

diff --git a/arch/arm/boot/dts/stm32mp15xx-dhcom-drc02.dtsi b/arch/arm/boot/dts/stm32mp15xx-dhcom-drc02.dtsi
index 62ab23824a3e..cb68afbbea68 100644
--- a/arch/arm/boot/dts/stm32mp15xx-dhcom-drc02.dtsi
+++ b/arch/arm/boot/dts/stm32mp15xx-dhcom-drc02.dtsi
@@ -33,7 +33,7 @@ &gpiob {
 	 * during TX anyway and that it only controls drive enable DE
 	 * line. Hence, the RX is always enabled here.
 	 */
-	rs485-rx-en {
+	rs485-rx-en-hog {
 		gpio-hog;
 		gpios = <8 GPIO_ACTIVE_HIGH>;
 		output-low;
@@ -61,7 +61,7 @@ &gpioi {
 	 * order to reset the Hub when USB bus is powered down, but
 	 * so far there is no such functionality.
 	 */
-	usb-hub {
+	usb-hub-hog {
 		gpio-hog;
 		gpios = <2 GPIO_ACTIVE_HIGH>;
 		output-high;
diff --git a/arch/arm/boot/dts/stm32mp15xx-dhcom-picoitx.dtsi b/arch/arm/boot/dts/stm32mp15xx-dhcom-picoitx.dtsi
index 356150d28c42..b99f2b891629 100644
--- a/arch/arm/boot/dts/stm32mp15xx-dhcom-picoitx.dtsi
+++ b/arch/arm/boot/dts/stm32mp15xx-dhcom-picoitx.dtsi
@@ -43,7 +43,7 @@ &gpioa {
 	 * in order to turn on port power when USB bus is powered up, but so
 	 * far there is no such functionality.
 	 */
-	usb-port-power {
+	usb-port-power-hog {
 		gpio-hog;
 		gpios = <13 GPIO_ACTIVE_LOW>;
 		output-low;
-- 
2.29.2