[PATCH 3/5] ARM: dts: meson8: add the thermal-zones with cooling configuration

[Martin Blumenstingl]

The vendor kernel uses the following thermal-zone settings:
<= 70°C:
- CPU frequency limited to 1.608GHz
- GPU limited to 511MHz and 5 cores (pixel processors)

<= 80°C:
- CPU frequency limited to 1.2GHz
- GPU limited to 435MHz and 4 cores (pixel processors)

<= 90°C:
- CPU frequency limited to 0.804GHz
- GPU limited to 328MHz and 3 cores (pixel processors)

Add simplified thermal configuration which is taken from the
GXBB/GXL/GXM SoC family (which uses the same manufacturing process and
has the same maximum junction temperature of 125°C). With this the
thermal framework will try to keep the SoC temperature at or below 80°C
which is identical to the vendor kernel (with the exception of one GPU
pixel processor).

The number of GPU cores are not taken into account as this is not
supported.

Signed-off-by: Martin Blumenstingl <martin.blumenstingl at googlemail.com>
---
 arch/arm/boot/dts/meson8.dtsi | 54 +++++++++++++++++++++++++++++++++++
 1 file changed, 54 insertions(+)

diff --git a/arch/arm/boot/dts/meson8.dtsi b/arch/arm/boot/dts/meson8.dtsi
index 04688e8abce2..420324ea2ad7 100644
--- a/arch/arm/boot/dts/meson8.dtsi
+++ b/arch/arm/boot/dts/meson8.dtsi
@@ -9,6 +9,7 @@
 #include <dt-bindings/power/meson8-power.h>
 #include <dt-bindings/reset/amlogic,meson8b-clkc-reset.h>
 #include <dt-bindings/reset/amlogic,meson8b-reset.h>
+#include <dt-bindings/thermal/thermal.h>
 #include "meson.dtsi"
 
 / {
@@ -28,6 +29,7 @@ cpu0: cpu at 200 {
 			resets = <&clkc CLKC_RESET_CPU0_SOFT_RESET>;
 			operating-points-v2 = <&cpu_opp_table>;
 			clocks = <&clkc CLKID_CPUCLK>;
+			#cooling-cells = <2>; /* min followed by max */
 		};
 
 		cpu1: cpu at 201 {
@@ -39,6 +41,7 @@ cpu1: cpu at 201 {
 			resets = <&clkc CLKC_RESET_CPU1_SOFT_RESET>;
 			operating-points-v2 = <&cpu_opp_table>;
 			clocks = <&clkc CLKID_CPUCLK>;
+			#cooling-cells = <2>; /* min followed by max */
 		};
 
 		cpu2: cpu at 202 {
@@ -50,6 +53,7 @@ cpu2: cpu at 202 {
 			resets = <&clkc CLKC_RESET_CPU2_SOFT_RESET>;
 			operating-points-v2 = <&cpu_opp_table>;
 			clocks = <&clkc CLKID_CPUCLK>;
+			#cooling-cells = <2>; /* min followed by max */
 		};
 
 		cpu3: cpu at 203 {
@@ -61,6 +65,7 @@ cpu3: cpu at 203 {
 			resets = <&clkc CLKC_RESET_CPU3_SOFT_RESET>;
 			operating-points-v2 = <&cpu_opp_table>;
 			clocks = <&clkc CLKID_CPUCLK>;
+			#cooling-cells = <2>; /* min followed by max */
 		};
 	};
 
@@ -190,6 +195,54 @@ power-firmware at 4f00000 {
 		};
 	};
 
+	thermal-zones {
+		soc {
+			polling-delay-passive = <250>; /* milliseconds */
+			polling-delay = <1000>; /* milliseconds */
+			thermal-sensors = <&thermal_sensor>;
+
+			cooling-maps {
+				map0 {
+					trip = <&soc_passive>;
+					cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&mali THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+				};
+
+				map1 {
+					trip = <&soc_hot>;
+					cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&mali THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+				};
+			};
+
+			trips {
+				soc_passive: soc-passive {
+					temperature = <80000>; /* millicelsius */
+					hysteresis = <2000>; /* millicelsius */
+					type = "passive";
+				};
+
+				soc_hot: soc-hot {
+					temperature = <90000>; /* millicelsius */
+					hysteresis = <2000>; /* millicelsius */
+					type = "hot";
+				};
+
+				soc_critical: soc-critical {
+					temperature = <110000>; /* millicelsius */
+					hysteresis = <2000>; /* millicelsius */
+					type = "critical";
+				};
+			};
+		};
+	};
+
 	mmcbus: bus at c8000000 {
 		compatible = "simple-bus";
 		reg = <0xc8000000 0x8000>;
@@ -254,6 +307,7 @@ mali: gpu at c0000 {
 			clocks = <&clkc CLKID_CLK81>, <&clkc CLKID_MALI>;
 			clock-names = "bus", "core";
 			operating-points-v2 = <&gpu_opp_table>;
+			#cooling-cells = <2>; /* min followed by max */
 		};
 	};
 }; /* end of / */
-- 
2.29.2