[v4,2/3] PCI: mediatek: Add new generation controller support

[Jianjun Wang]

On Fri, 2020-12-04 at 12:30 -0600, Bjorn Helgaas wrote:
> On Fri, Dec 04, 2020 at 08:39:09AM +0100, Lukas Wunner wrote:
> > On Mon, Nov 30, 2020 at 11:30:05AM -0600, Bjorn Helgaas wrote:
> > > On Mon, Nov 23, 2020 at 02:45:13PM +0800, Jianjun Wang wrote:
> > > > On Thu, 2020-11-19 at 14:28 -0600, Bjorn Helgaas wrote:
> > > > > > +static int mtk_pcie_setup(struct mtk_pcie_port *port)
> > > > > > +{
> > [...]
> > > > > > +	/* Try link up */
> > > > > > +	err = mtk_pcie_startup_port(port);
> > > > > > +	if (err) {
> > > > > > +		dev_notice(dev, "PCIe link down\n");
> > > > > > +		goto err_setup;
> > > > > 
> > > > > Generally it should not be a fatal error if the link is not up at
> > > > > probe-time.  You may be able to hot-add a device, or the device may
> > > > > have some external power control that will power it up later.
> > > > 
> > > > This is for the power saving requirement. If there is no device
> > > > connected with the PCIe slot, the PCIe MAC and PHY should be powered
> > > > off.
> > > > 
> > > > Is there any standard flow to support power down the hardware at
> > > > probe-time if no device is connected and power it up when hot-add a
> > > > device?
> > > 
> > > That's a good question.  I assume this looks like a standard PCIe
> > > hot-add event?
> > > 
> > > When you hot-add a device, does the Root Port generate a Presence
> > > Detect Changed interrupt?  The pciehp driver should field that
> > > interrupt and turn on power to the slot via the Power Controller
> > > Control bit in the Slot Control register.
> > > 
> > > Does your hardware require something more than that to control the MAC
> > > and PHY power?
> > 
> > Power saving of unused PCIe ports is generally achieved through the
> > runtime PM framework.  When a PCIe port runtime suspends, the PCIe
> > core will transition it to D3hot.  On top of that, the platform
> > may be able to transition the port to D3cold.  Currently only the
> > ACPI platform supports that.  Conceivably, devicetree-based systems
> > may want to disable certain clocks or regulators when a PCIe port
> > runtime suspends.  I think we do not support that yet but it could
> > be added to drivers/pci/pcie/portdrv*.
> > 
> > A hotplug port is expected to signal PDC and DLLSC interrupts even
> > when in D3hot.  At least that's our experience with Thunderbolt.
> > To support hotplug interrupts in D3cold, some external mechanism
> > (such as a PME) is necessary to wake up the port on hotplug.
> > This is also supported with recent Thunderbolt systems.
> > 
> > Because we've seen various incompatibilities when runtime suspending
> > PCIe ports, certain conditions must be satisfied for runtime PM
> > to be enabled.  They're encoded in pci_bridge_d3_possible().
> > Generally, hotplug ports only runtime suspend if they belong to
> > a Thunderbolt controller or if the ACPI platform explicitly allows
> > runtime PM (through presence of a _PR3 method or a device property).
> > Non-hotplug ports runtime suspend if the BIOS is newer than 2015
> > (as specified by DMI).
> > 
> > Obviously, this policy is very x86-focussed because both Thunderbolt
> > and DMI are only really a thing on x86.  That's about to change though
> > because Apple's new arm64-based Macs have Thunderbolt integrated into
> > the SoC and arm64 SoCs are making inroads in the datacenter, which is
> > an important use case for PCIe hotplug (hot-swappable NVMe drives).
> > So we may have to amend pci_bridge_d3_possible() to whitelist
> > PCIe ports for runtime PM on specific arches or systems.
> 
> Thanks for all this very useful information!
> 
> My interpretation for the mediatek situation:
> 
>   - I assume this patch leaves or puts the Root Port in D3cold if no
>     downstream devices are present.
> 
>   - I don't see any support for PME or similar mechanisms to signal a
>     hot-add while the RP is in D3cold.
> 
>   - So I assume you don't support hot-add if the slot was empty at
>     boot and that's acceptable for your platform.

Yes, the hardware of Root Port will be totally powered off by gating its
MTCMOS and clocks if the slot is empty at boot time. Because we are
focus on the scenario of power saving, it's acceptable if we don't
support hot-add.

Thanks.