[PATCH v7 8/8] ARM: dts: add Plymovent BAS board
Oleksij Rempel
o.rempel at pengutronix.de
Mon Dec 7 09:09:39 EST 2020
Plymovent BAS is a base system controller produced for the Plymovent filter
systems.
Co-Developed-by: David Jander <david at protonic.nl>
Signed-off-by: David Jander <david at protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel at pengutronix.de>
---
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/imx6dl-plybas.dts | 394 ++++++++++++++++++++++++++++
2 files changed, 395 insertions(+)
create mode 100644 arch/arm/boot/dts/imx6dl-plybas.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 31249fc5f85c..ee725aebc3a8 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -461,6 +461,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
imx6dl-pico-hobbit.dtb \
imx6dl-pico-nymph.dtb \
imx6dl-pico-pi.dtb \
+ imx6dl-plybas.dtb \
imx6dl-plym2m.dtb \
imx6dl-prtrvt.dtb \
imx6dl-prtvt7.dtb \
diff --git a/arch/arm/boot/dts/imx6dl-plybas.dts b/arch/arm/boot/dts/imx6dl-plybas.dts
new file mode 100644
index 000000000000..333c306aa946
--- /dev/null
+++ b/arch/arm/boot/dts/imx6dl-plybas.dts
@@ -0,0 +1,394 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright (c) 2014 Protonic Holland
+ * Copyright (c) 2020 Oleksij Rempel <kernel at pengutronix.de>, Pengutronix
+ */
+
+/dts-v1/;
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
+#include "imx6dl.dtsi"
+
+/ {
+ model = "Plymovent BAS board";
+ compatible = "ply,plybas", "fsl,imx6dl";
+
+ chosen {
+ stdout-path = &uart4;
+ };
+
+ gpio_keys {
+ compatible = "gpio-keys";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ autorepeat;
+
+ button at 20 {
+ label = "START";
+ linux,code = <31>;
+ gpios = <&gpio5 8 GPIO_ACTIVE_LOW>;
+ };
+
+ button at 21 {
+ label = "CLEAN";
+ linux,code = <46>;
+ gpios = <&gpio5 9 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_leds>;
+
+ led-0 {
+ label = "debug0";
+ gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>;
+ };
+
+ led-1 {
+ label = "debug1";
+ gpios = <&gpio1 9 GPIO_ACTIVE_HIGH>;
+ };
+
+ led-2 {
+ label = "light_tower1";
+ gpios = <&gpio4 22 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
+ };
+
+ led-3 {
+ label = "light_tower2";
+ gpios = <&gpio4 23 GPIO_ACTIVE_HIGH>;
+ };
+
+ led-4 {
+ label = "light_tower3";
+ gpios = <&gpio4 24 GPIO_ACTIVE_HIGH>;
+ };
+
+ led-5 {
+ label = "light_tower4";
+ gpios = <&gpio4 25 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ clk50m_phy: phy-clock {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <50000000>;
+ };
+
+ reg_5v0: regulator-5v0 {
+ compatible = "regulator-fixed";
+ regulator-name = "5v0";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ };
+};
+
+&can1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_can1>;
+ xceiver-supply = <®_5v0>;
+ status = "okay";
+};
+
+&can2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_can2>;
+ xceiver-supply = <®_5v0>;
+ status = "okay";
+};
+
+&ecspi1 {
+ cs-gpios = <&gpio3 19 GPIO_ACTIVE_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi1>;
+ status = "okay";
+
+ flash at 0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <20000000>;
+ };
+};
+
+&fec {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enet>;
+ phy-mode = "rmii";
+ clocks = <&clks IMX6QDL_CLK_ENET>,
+ <&clks IMX6QDL_CLK_ENET>,
+ <&clk50m_phy>;
+ clock-names = "ipg", "ahb", "ptp";
+ phy-handle = <&rgmii_phy>;
+ status = "okay";
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ /* Microchip KSZ8081RNA PHY */
+ rgmii_phy: ethernet-phy at 0 {
+ reg = <0>;
+ interrupts-extended = <&gpio4 30 IRQ_TYPE_LEVEL_LOW>;
+ reset-gpios = <&gpio4 26 GPIO_ACTIVE_LOW>;
+ reset-assert-us = <10000>;
+ reset-deassert-us = <300>;
+ };
+ };
+};
+
+&gpio1 {
+ gpio-line-names =
+ "", "SD1_CD", "", "", "", "", "", "",
+ "DEBUG_0", "DEBUG_1", "", "", "", "", "", "",
+ "", "", "", "", "", "", "", "",
+ "", "", "", "", "", "", "", "";
+};
+
+&gpio3 {
+ gpio-line-names =
+ "", "", "", "", "", "", "", "",
+ "", "", "", "", "", "", "", "",
+ "", "", "", "ECSPI1_SS1", "", "USB_EXT_PWR", "", "",
+ "", "", "", "", "", "", "", "";
+};
+
+&gpio4 {
+ gpio-line-names =
+ "", "", "", "", "", "", "", "",
+ "", "", "", "", "CAN1_SR", "CAN2_SR", "", "",
+ "LED_DI0_DEBUG_0", "LED_DI0_DEBUG_1", "IMX6_IN12", "IMX6_HMI",
+ "IMX6_IN11", "IMX6_BUZZER", "IMX6_LED1", "IMX6_LED2",
+ "IMX6_LED3", "IMX6_LED4", "ETH_RESET", "IMX6_ANA_OUT_SD",
+ "IMX6_ANA_OUT_ERR", "IMX6_ANA_OUT", "ETH_INTRP", "";
+};
+
+&gpio5 {
+ gpio-line-names =
+ "", "", "", "", "", "IMX6_RELAY1", "IMX6_RELAY2", "",
+ "IMX6_IN1", "IMX6_IN2", "IMX6_IN3", "IMX6_IN4", "IMX6_IN5",
+ "IMX6_IN6", "IMX6_IN7", "IMX6_IN8",
+ "IMX6_IN9", "IMX6_IN10", "", "", "", "", "", "",
+ "", "", "", "", "", "", "", "";
+};
+
+&i2c1 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c1>;
+ status = "okay";
+
+ /* additional i2c devices are added automatically by the boot loader */
+};
+
+&i2c3 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c3>;
+ status = "okay";
+
+ temperature-sensor at 70 {
+ compatible = "ti,tmp103";
+ reg = <0x70>;
+ };
+
+ rtc at 51 {
+ compatible = "nxp,pcf8563";
+ reg = <0x51>;
+ };
+};
+
+&pwm1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm1>;
+ status = "okay";
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart1>;
+ status = "okay";
+};
+
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart2>;
+ fsl,uart-has-rtscts;
+ linux,rs485-enabled-at-boot-time;
+ rs485-rts-delay = <0 20>;
+ status = "okay";
+};
+
+&uart4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart4>;
+ status = "okay";
+};
+
+&usbotg {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usbotg>;
+ phy_type = "utmi";
+ dr_mode = "host";
+ disable-over-current;
+ status = "okay";
+};
+
+&usbphynop1 {
+ status = "disabled";
+};
+
+&usbphynop2 {
+ status = "disabled";
+};
+
+&iomuxc {
+ pinctrl_can1: can1grp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_ROW2__FLEXCAN1_RX 0x1b000
+ MX6QDL_PAD_KEY_COL2__FLEXCAN1_TX 0x3008
+ /* CAN1_SR */
+ MX6QDL_PAD_KEY_COL3__GPIO4_IO12 0x13008
+ >;
+ };
+
+ pinctrl_can2: can2grp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_ROW4__FLEXCAN2_RX 0x1b000
+ MX6QDL_PAD_KEY_COL4__FLEXCAN2_TX 0x3008
+ /* CAN2_SR */
+ MX6QDL_PAD_KEY_ROW3__GPIO4_IO13 0x13008
+ >;
+ };
+
+ pinctrl_ecspi1: ecspi1grp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D17__ECSPI1_MISO 0x1b000
+ MX6QDL_PAD_EIM_D18__ECSPI1_MOSI 0x3008
+ MX6QDL_PAD_EIM_D16__ECSPI1_SCLK 0x3008
+ /* CS */
+ MX6QDL_PAD_EIM_D19__GPIO3_IO19 0x3008
+ >;
+ };
+
+ pinctrl_enet: enetgrp {
+ fsl,pins = <
+ /* MX6QDL_ENET_PINGRP4 */
+ MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b0b0
+ MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b0b0
+ MX6QDL_PAD_ENET_RXD0__ENET_RX_DATA0 0x1b0b0
+ MX6QDL_PAD_ENET_RXD1__ENET_RX_DATA1 0x1b0b0
+ MX6QDL_PAD_ENET_RX_ER__ENET_RX_ER 0x1b0b0
+ MX6QDL_PAD_ENET_TX_EN__ENET_TX_EN 0x1b0b0
+ MX6QDL_PAD_ENET_TXD0__ENET_TX_DATA0 0x1b0b0
+ MX6QDL_PAD_ENET_TXD1__ENET_TX_DATA1 0x1b0b0
+ MX6QDL_PAD_ENET_CRS_DV__ENET_RX_EN 0x1b0b0
+
+ MX6QDL_PAD_GPIO_16__ENET_REF_CLK 0x1b0b0
+ /* Phy reset */
+ MX6QDL_PAD_DISP0_DAT5__GPIO4_IO26 0x1b0b0
+ /* nINTRP */
+ MX6QDL_PAD_DISP0_DAT9__GPIO4_IO30 0x1b0b0
+ >;
+ };
+
+ pinctrl_i2c1: i2c1grp {
+ fsl,pins = <
+ MX6QDL_PAD_CSI0_DAT8__I2C1_SDA 0x4001f8b1
+ MX6QDL_PAD_CSI0_DAT9__I2C1_SCL 0x4001f8b1
+ >;
+ };
+
+ pinctrl_i2c3: i2c3grp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_5__I2C3_SCL 0x4001b8b1
+ MX6QDL_PAD_GPIO_6__I2C3_SDA 0x4001b8b1
+ >;
+ };
+
+ pinctrl_leds: ledsgrp {
+ fsl,pins = <
+ /* DEBUG_0 */
+ MX6QDL_PAD_GPIO_8__GPIO1_IO08 0x1b0b0
+ /* DEBUG_1 */
+ MX6QDL_PAD_GPIO_9__GPIO1_IO09 0x1b0b0
+
+ /* LED1 (lighttower) */
+ MX6QDL_PAD_DISP0_DAT1__GPIO4_IO22 0x13070
+ /* LED2 (lighttower) */
+ MX6QDL_PAD_DISP0_DAT2__GPIO4_IO23 0x13070
+ /* LED3 (lighttower) */
+ MX6QDL_PAD_DISP0_DAT3__GPIO4_IO24 0x13070
+ /* LED4 (lighttower) */
+ MX6QDL_PAD_DISP0_DAT4__GPIO4_IO25 0x13070
+ >;
+ };
+
+ pinctrl_pwm1: pwm1grp {
+ fsl,pins = <
+ MX6QDL_PAD_DISP0_DAT8__PWM1_OUT 0x1b0b0
+ >;
+ };
+
+ /* YaCO AUX Uart */
+ pinctrl_uart1: uart1grp {
+ fsl,pins = <
+ MX6QDL_PAD_CSI0_DAT10__UART1_TX_DATA 0x1b0b1
+ MX6QDL_PAD_CSI0_DAT11__UART1_RX_DATA 0x1b0b1
+ >;
+ };
+
+ pinctrl_uart2: uart2grp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D26__UART2_TX_DATA 0x1b0b1
+ MX6QDL_PAD_EIM_D27__UART2_RX_DATA 0x1b0b1
+ MX6QDL_PAD_EIM_D28__UART2_DTE_CTS_B 0x130b1
+ >;
+ };
+
+ pinctrl_uart4: uart4grp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_COL0__UART4_TX_DATA 0x1b0b1
+ MX6QDL_PAD_KEY_ROW0__UART4_RX_DATA 0x1b0b1
+ >;
+ };
+
+ pinctrl_usbotg: usbotggrp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D21__USB_OTG_OC 0x1b0b0
+ /* power enable, high active */
+ MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x1b0b0
+ >;
+ };
+
+ pinctrl_usdhc1: usdhc1grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD1_CMD__SD1_CMD 0x170f9
+ MX6QDL_PAD_SD1_CLK__SD1_CLK 0x100f9
+ MX6QDL_PAD_SD1_DAT0__SD1_DATA0 0x170f9
+ MX6QDL_PAD_SD1_DAT1__SD1_DATA1 0x170f9
+ MX6QDL_PAD_SD1_DAT2__SD1_DATA2 0x170f9
+ MX6QDL_PAD_SD1_DAT3__SD1_DATA3 0x170f9
+ MX6QDL_PAD_GPIO_1__GPIO1_IO01 0x1b0b0
+ >;
+ };
+
+ pinctrl_usdhc3: usdhc3grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD3_CMD__SD3_CMD 0x17099
+ MX6QDL_PAD_SD3_CLK__SD3_CLK 0x10099
+ MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x17099
+ MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x17099
+ MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x17099
+ MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x17099
+ MX6QDL_PAD_SD3_DAT4__SD3_DATA4 0x17099
+ MX6QDL_PAD_SD3_DAT5__SD3_DATA5 0x17099
+ MX6QDL_PAD_SD3_DAT6__SD3_DATA6 0x17099
+ MX6QDL_PAD_SD3_DAT7__SD3_DATA7 0x17099
+ MX6QDL_PAD_SD3_RST__SD3_RESET 0x1b0b1
+ >;
+ };
+};
--
2.29.2
More information about the linux-arm-kernel
mailing list