[linux-sunxi] [PATCH 8/8] arm64: dts: allwinner: Add OrangePi Zero 2 .dts
Clément Péron
peron.clem at gmail.com
Sun Dec 6 07:51:15 EST 2020
Hi Andre,
On Wed, 2 Dec 2020 at 14:54, Andre Przywara <andre.przywara at arm.com> wrote:
>
> The OrangePi Zero 2 is a development board with the new H616 SoC.
>
> It features the usual connectors used on those small boards, and comes
> with the AXP305, which seems to be compatible with the AXP805.
>
> For more details see: http://linux-sunxi.org/Xunlong_Orange_Pi_Zero2
>
> Signed-off-by: Andre Przywara <andre.przywara at arm.com>
> ---
> arch/arm64/boot/dts/allwinner/Makefile | 1 +
> .../allwinner/sun50i-h616-orangepi-zero2.dts | 228 ++++++++++++++++++
> 2 files changed, 229 insertions(+)
> create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h616-orangepi-zero2.dts
>
> diff --git a/arch/arm64/boot/dts/allwinner/Makefile b/arch/arm64/boot/dts/allwinner/Makefile
> index 211d1e9d4701..0cf8299b1ce7 100644
> --- a/arch/arm64/boot/dts/allwinner/Makefile
> +++ b/arch/arm64/boot/dts/allwinner/Makefile
> @@ -35,3 +35,4 @@ dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-orangepi-one-plus.dtb
> dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-pine-h64.dtb
> dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-pine-h64-model-b.dtb
> dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-tanix-tx6.dtb
> +dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h616-orangepi-zero2.dtb
> diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h616-orangepi-zero2.dts b/arch/arm64/boot/dts/allwinner/sun50i-h616-orangepi-zero2.dts
> new file mode 100644
> index 000000000000..814f5b4fec7c
> --- /dev/null
> +++ b/arch/arm64/boot/dts/allwinner/sun50i-h616-orangepi-zero2.dts
> @@ -0,0 +1,228 @@
> +// SPDX-License-Identifier: (GPL-2.0+ or MIT)
> +/*
> + * Copyright (C) 2020 Arm Ltd.
> + */
> +
> +/dts-v1/;
> +
> +#include "sun50i-h616.dtsi"
> +
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/interrupt-controller/arm-gic.h>
> +
> +/ {
> + model = "OrangePi Zero2";
> + compatible = "xunlong,orangepi-zero2", "allwinner,sun50i-h616";
You need to add this compatible to the sunxi.yaml boards list
> +
> + aliases {
> + ethernet0 = &emac0;
> + serial0 = &uart0;
> + };
> +
> + chosen {
> + stdout-path = "serial0:115200n8";
> + };
> +
> + leds {
> + compatible = "gpio-leds";
> +
> + power {
> + label = "orangepi:red:power";
label is deprecated
function = LED_FUNCTION_POWER;
color = <LED_COLOR_ID_RED>;
> + gpios = <&pio 2 13 GPIO_ACTIVE_HIGH>; /* PC13 */
> + default-state = "on";
> + };
> +
> + status {
> + label = "orangepi:green:status";
same here
function = LED_FUNCTION_STATUS;
color = <LED_COLOR_ID_GREEN>;
> + gpios = <&pio 2 12 GPIO_ACTIVE_HIGH>; /* PC12 */
> + };
> + };
> +
> + reg_vcc5v: vcc5v {
> + /* board wide 5V supply directly from the USB-C socket */
> + compatible = "regulator-fixed";
> + regulator-name = "vcc-5v";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + regulator-always-on;
> + };
> +
> + reg_usb1_vbus: usb1-vbus {
> + compatible = "regulator-fixed";
> + regulator-name = "usb1-vbus";
Could you add reg_vcc5v as vin-supply.
This doesn't change anything but will be a better description of the HW.
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + enable-active-high;
> + gpio = <&pio 2 16 GPIO_ACTIVE_HIGH>; /* PC16 */
> + status = "okay";
> + };
> +};
> +
> +&ehci0 {
> + status = "okay";
> +};
> +
> +&ehci1 {
> + status = "okay";
> +};
> +
> +/* USB 2 & 3 are on headers only. */
> +
> +&emac0 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&ext_rgmii_pins>;
> + phy-mode = "rgmii";
> + phy-handle = <&ext_rgmii_phy>;
> + phy-supply = <®_dcdce>;
> + allwinner,rx-delay-ps = <3100>;
> + allwinner,tx-delay-ps = <700>;
> + status = "okay";
> +};
> +
> +&mdio {
> + ext_rgmii_phy: ethernet-phy at 1 {
> + compatible = "ethernet-phy-ieee802.3-c22";
> + reg = <1>;
> + };
> +};
> +
> +&mmc0 {
> + vmmc-supply = <®_dcdce>;
> + cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
> + bus-width = <4>;
> + status = "okay";
> +};
> +
> +&ohci0 {
> + status = "okay";
> +};
> +
> +&ohci1 {
> + status = "okay";
> +};
> +
> +&r_i2c {
> + status = "okay";
> +
> + axp305: pmic at 36 {
> + compatible = "x-powers,axp305", "x-powers,axp805",
> + "x-powers,axp806";
> + reg = <0x36>;
> +
> + /* dummy interrupt to appease the driver for now */
> + interrupts = <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>;
> + interrupt-controller;
> + #interrupt-cells = <1>;
> +
> + x-powers,self-working-mode;
> + vina-supply = <®_vcc5v>;
> + vinb-supply = <®_vcc5v>;
> + vinc-supply = <®_vcc5v>;
> + vind-supply = <®_vcc5v>;
> + vine-supply = <®_vcc5v>;
> + aldoin-supply = <®_vcc5v>;
> + bldoin-supply = <®_vcc5v>;
> + cldoin-supply = <®_vcc5v>;
> +
> + regulators {
> + reg_aldo1: aldo1 {
> + regulator-always-on;
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-name = "vcc-sys";
> + };
> +
> + reg_aldo2: aldo2 {
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-name = "vcc3v3-ext";
> + };
> +
> + reg_aldo3: aldo3 {
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-name = "vcc3v3-ext2";
> + };
> +
> + reg_bldo1: bldo1 {
> + regulator-always-on;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-name = "vcc1v8";
> + };
> +
> + bldo2 {
> + /* unused */
> + };
> +
> + bldo3 {
> + /* unused */
> + };
> +
> + bldo4 {
> + /* unused */
> + };
> +
> + cldo1 {
> + /* reserved */
> + };
> +
> + cldo2 {
> + /* unused */
> + };
> +
> + cldo3 {
> + /* unused */
> + };
> +
> + reg_dcdca: dcdca {
> + regulator-always-on;
> + regulator-min-microvolt = <810000>;
> + regulator-max-microvolt = <1080000>;
> + regulator-name = "vdd-cpu";
> + };
> +
> + reg_dcdcc: dcdcc {
> + regulator-always-on;
> + regulator-min-microvolt = <810000>;
> + regulator-max-microvolt = <1080000>;
> + regulator-name = "vdd-gpu-sys";
> + };
> +
> + reg_dcdcd: dcdcd {
> + regulator-always-on;
> + regulator-min-microvolt = <1500000>;
> + regulator-max-microvolt = <1500000>;
> + regulator-name = "vdd-dram";
> + };
> +
> + reg_dcdce: dcdce {
> + regulator-boot-on;
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-name = "vcc-eth-mmc";
> + };
> +
> + sw {
> + /* unused */
> + };
> + };
> + };
> +};
> +
> +&uart0 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&uart0_ph_pins>;
> + status = "okay";
> +};
> +
> +&usbotg {
> + dr_mode = "otg";
> + status = "okay";
> +};
> +
> +&usbphy {
> + usb0_vbus-supply = <®_vcc5v>;
> + usb1_vbus-supply = <®_usb1_vbus>;
> + status = "okay";
> +};
> --
> 2.17.5
>
> --
> You received this message because you are subscribed to the Google Groups "linux-sunxi" group.
> To unsubscribe from this group and stop receiving emails from it, send an email to linux-sunxi+unsubscribe at googlegroups.com.
> To view this discussion on the web, visit https://groups.google.com/d/msgid/linux-sunxi/20201202135409.13683-9-andre.przywara%40arm.com.
More information about the linux-arm-kernel
mailing list