[PATCH] drm: mxsfb: Add interconnect path request

[Lucas Stach]

Am Dienstag, den 01.12.2020, 11:37 +0100 schrieb Martin Kepplinger:
> Add interconnect support to mxsfb so that it is able to request enough
> bandwidth to DDR for display output to work.
> 
> Signed-off-by: Martin Kepplinger <martin.kepplinger at puri.sm>
> ---
>  drivers/gpu/drm/mxsfb/mxsfb_drv.c | 33 +++++++++++++++++++++++++++++++
>  drivers/gpu/drm/mxsfb/mxsfb_drv.h |  2 ++
>  drivers/gpu/drm/mxsfb/mxsfb_kms.c | 13 ++++++++++++
>  3 files changed, 48 insertions(+)
> 
> diff --git a/drivers/gpu/drm/mxsfb/mxsfb_drv.c b/drivers/gpu/drm/mxsfb/mxsfb_drv.c
> index 6faf17b6408d..b05e8e5f1e38 100644
> --- a/drivers/gpu/drm/mxsfb/mxsfb_drv.c
> +++ b/drivers/gpu/drm/mxsfb/mxsfb_drv.c
> @@ -15,6 +15,7 @@
>  #include <linux/of_device.h>
>  #include <linux/platform_device.h>
>  #include <linux/pm_runtime.h>
> +#include <linux/interconnect.h>
>  
> 
> 
> 
>  #include <drm/drm_atomic_helper.h>
>  #include <drm/drm_bridge.h>
> @@ -311,6 +312,34 @@ static const struct of_device_id mxsfb_dt_ids[] = {
>  };
>  MODULE_DEVICE_TABLE(of, mxsfb_dt_ids);
> 
> +
> +static int mxsfb_init_icc(struct platform_device *pdev)
> +{
> +	struct drm_device *drm = platform_get_drvdata(pdev);
> +	struct mxsfb_drm_private *mxsfb = drm->dev_private;
> +	int ret;
> +
> +	/* Optional interconnect request */
> +	mxsfb->icc_path = devm_of_icc_get(&pdev->dev, "lcdif-dram");
> +	if (IS_ERR(mxsfb->icc_path)) {
> +		ret = PTR_ERR(mxsfb->icc_path);
> +		if (ret == -EPROBE_DEFER)
> +			return ret;
> +
> +		mxsfb->icc_path = NULL;
> +		dev_dbg(drm->dev,
> +			"No interconnect may cause display underflows!\n");
> +	}
> +
> +	ret = icc_set_bw(mxsfb->icc_path, 0, MBps_to_icc(700));

Shouldn't this be proportional to the current mode, instead of a fixed
value? 700MB looks like 1080p at 60Hz@32bpp with a bit of headroom, but
there are many valid use-cases where significantly smaller displays are
connected to the eLCDIF. Also it doesn't cover the case where an
overlay is active, which needs additional bandwidth.

> +	if (ret) {
> +		dev_err(drm->dev, "%s: icc_set_bw failed: %d\n", __func__, ret);
> +		return ret;
> +	}
> +
> +	return 0;
> +}
> +
[...]
>  #include <drm/drm_atomic.h>
>  #include <drm/drm_atomic_helper.h>
> @@ -310,6 +311,12 @@ static void mxsfb_crtc_atomic_enable(struct drm_crtc *crtc,
>  	struct mxsfb_drm_private *mxsfb = to_mxsfb_drm_private(crtc->dev);
>  	struct drm_device *drm = mxsfb->drm;
>  	dma_addr_t paddr;
> +	int ret;
> +
> +	ret = icc_enable(mxsfb->icc_path);
> +	if (ret)
> +		dev_err_ratelimited(drm->dev, "%s: icc_enable failed: %d\n",
> +				    __func__, ret);

Why ratelimited? I wouldn't expect atomic enable/disable to be called
often enough for this to make any difference.

Regards,
Lucas

> 
>  	pm_runtime_get_sync(drm->dev);
>  	mxsfb_enable_axi_clk(mxsfb);