[PATCH 7/7] [NOT FOR MERGE] ARM: dts: sun8i: a83t: bananapi-m3: Enable OV8865 camera

[Maxime Ripard]

Hi,

On Fri, Aug 21, 2020 at 04:59:35PM +0200, Kévin L'hôpital wrote:
> The Bananapi M3 supports a camera module which includes an
> OV8865 sensor connected via the parallel CSI interface and
> an OV8865 sensor connected via MIPI CSI-2.
> 
> The I2C2 bus is shared by the two sensors as well as active-low
> reset signal but each sensor has it own shutdown line.
> 
> The I2c address for the OV8865 is 0x36.
> 
> The bus type is hardcoded to 4 due to the lack of available
> define usable in the device-tree.
> 
> Signed-off-by: Kévin L'hôpital <kevin.lhopital at bootlin.com>
>
> ---
>  arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts | 99 ++++++++++++++++++++
>  1 file changed, 99 insertions(+)
> 
> diff --git a/arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts b/arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts
> index 9d34eabba121..f7839094695e 100644
> --- a/arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts
> +++ b/arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts
> @@ -85,6 +85,38 @@
>  		};
>  	};
>  
> +	reg_ov8865_avdd: ov8865-avdd {
> +		compatible = "regulator-fixed";
> +		regulator-name = "ov8865-avdd";
> +		regulator-min-microvolt = <2800000>;
> +		regulator-max-microvolt = <2800000>;
> +		vin-supply = <&reg_dldo4>;
> +	};
> +
> +	reg_ov8865_dovdd: ov8865-dovdd {
> +		compatible = "regulator-fixed";
> +		regulator-name = "ov8865-dovdd";
> +		regulator-min-microvolt = <2800000>;
> +		regulator-max-microvolt = <2800000>;
> +		vin-supply = <&reg_dldo4>;
> +	};
> +
> +	reg_ov8865_afvdd: ov8865-afvdd {
> +		compatible = "regulator-fixed";
> +		regulator-name = "ov8865-afvdd";
> +		regulator-min-microvolt = <2800000>;
> +		regulator-max-microvolt = <2800000>;
> +		vin-supply = <&reg_dldo4>;
> +	};
> +
> +	reg_ov8865_vdd2: ov8865-vdd2 {
> +		compatible = "regulator-fixed";
> +		regulator-name = "ov8865-vdd2";
> +		regulator-min-microvolt = <1200000>;
> +		regulator-max-microvolt = <1200000>;
> +		vin-supply = <&reg_eldo1>;
> +	};
> +
>  	reg_usb1_vbus: reg-usb1-vbus {
>  		compatible = "regulator-fixed";
>  		regulator-name = "usb1-vbus";
> @@ -115,10 +147,59 @@
>  	cpu-supply = <&reg_dcdc3>;
>  };
>  
> +&ccu {
> +	assigned-clocks = <&ccu CLK_CSI_MCLK>;
> +	assigned-clock-parents = <&osc24M>;
> +	assigned-clock-rates = <24000000>;
> +};

Why do you need to use assigned-clocks here?

> +&csi {
> +	pinctrl-names = "default";
> +	status = "okay";
> +};

pinctrl-names alone is useless

> +
> +&csi_in {
> +	mipi_csi2_from_ov8865: endpoint {
> +		remote-endpoint = <&ov8865_to_mipi_csi2>;
> +		clock-lanes = <0>;
> +		data-lanes = <1 2 3 4>;
> +		bus-type = <4>;
> +	};
> +};
> +
>  &de {
>  	status = "okay";
>  };
>  
> +&i2c2 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&i2c2_pe_pins>;
> +	status = "okay";
> +
> +	ov8865: camera at 36 {
> +		compatible = "ovti,ov8865";
> +		reg = <0x36>;
> +		clocks = <&ccu CLK_CSI_MCLK>;
> +		clock-names ="xclk";
> +		AVDD-supply = <&reg_ov8865_avdd>;
> +		DOVDD-supply = <&reg_ov8865_dovdd>;
> +		VDD2-supply = <&reg_ov8865_vdd2>;
> +		AFVDD-supply = <&reg_ov8865_afvdd>;
> +		powerdown-gpios = <&pio 4 17 GPIO_ACTIVE_LOW>; /* PE17 */
> +		reset-gpios = <&pio 4 16 GPIO_ACTIVE_LOW>; /* PE16 */
> +		rotation = <180>;
> +
> +		port {
> +			ov8865_to_mipi_csi2: endpoint {
> +				remote-endpoint = <&mipi_csi2_from_ov8865>;
> +				data-lanes = <1 2 3 4>;
> +				clock-lanes = <0>;
> +				bus-type = <4>; /* V4L2_FWNODE_BUS_TYPE_CSI2_DPHY */
> +			};
> +		};
> +	};
> +};
> +
>  &ehci0 {
>  	/* Terminus Tech FE 1.1s 4-port USB 2.0 hub here */
>  	status = "okay";
> @@ -191,6 +272,11 @@
>  	status = "okay";
>  };
>  
> +&pio {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&csi_mclk_pin>;
> +};

I'm not sure why you'd need to use the MCLK pin as a hog, assigning it
to the camera device should be enough?

Maxime