[PATCH v3 1/2] arm64: dts: meson-g12b-odroid-n2: Enable RTC controller node

[Anand Moon]

Hi Jerome

On Mon, 24 Aug 2020 at 20:00, Jerome Brunet <jbrunet at baylibre.com> wrote:
>
>
> On Mon 24 Aug 2020 at 15:50, Neil Armstrong <narmstrong at baylibre.com> wrote:
>
> > On 24/08/2020 15:41, Anand Moon wrote:
> >> hi All,
> >>
> >> On Fri, 21 Aug 2020 at 10:13, Anand Moon <linux.amoon at gmail.com> wrote:
> >>>
> >>> Hi Kevin,
> >>>
> >>> Thanks for your review comments.
> >>>
> >>> On Fri, 21 Aug 2020 at 01:03, Kevin Hilman <khilman at baylibre.com> wrote:
> >>>>
> >>>> Anand Moon <linux.amoon at gmail.com> writes:
> >>>>
> >>>>> Enable RTC PCF8563 node on Odroid-N2 SBC, In order to
> >>>>> support the RTC wakealarm feature for suspend and resume.
> >>>>> Also assign an alias to the pcf8563 to rtc0 and meson-vrtc to rtc1
> >>>>> timer device to prevent it being assigned to /dev/rtc0
> >>>>> which disto userspace tools assume is a clock device.
> >>>>>
> >>>>> Cc: Neil Armstrong <narmstrong at baylibre.com>
> >>>>> Cc: Kevin Hilman <khilman at baylibre.com>
> >>>>> Suggested-by: Christian Hewitt <christianshewitt at gmail.com>
> >>>>> Signed-off-by: Anand Moon <linux.amoon at gmail.com>
> >>>>> ---
> >>>>> Changes V3
> >>>>> --Drop the INI GPIOAO.BIT7 pinctrl.
> >>>>
> >>>> Why did you drop this GPIO?  Isn't this the GPIO that the RTC uses to
> >>>> wakeup the system?  If so, this should be included as part of this
> >>>> patch.
> >>>>
> >>>> It probably still works because the bootloader configures this GPIO as
> >>>> input, but the kernel should not rely on the booloader for that, so
> >>>> please include as part of this patch.
> >>>>
> >>>
> >>> Ok I will figure out the correct pinctrl need for this settings.
> >>> looking into the Odroid N2 schematics.
> >>>
> >>
> >> I am trying to map the RTC INT pinctrl, ie RTC INT GPIOAO.BIT7.
> >
> >
> > Simply add:
> >
> > interrupt-parent = <&gpio_intc>;
> > interrupts = <7 IRQ_TYPE_LEVEL_LOW>;
> >
> > to reflect the interrupt connection.

I have tried this setting, but it is not working.

[alarm at archl-on2e ~]$ dmesg| grep rtc
[    5.378002] meson-vrtc ff8000a8.rtc: registered as rtc1
[    5.942307] rtc-pcf8563 0-0051: pcf8563_write_block_data: err=-110
addr=0e, data=03
[    5.942316] rtc-pcf8563 0-0051: pcf8563_probe: write error
[    5.945983] rtc-pcf8563: probe of 0-0051 failed with error -5


> >
> > No need to setup pinctrl here since the GPIO input is always connected
> > to the gpio irq generator whatever pinctrl mode is set.
>
> It is actually better to setup pinctrl. Yes the irq controller can work
> whatever the pin setup but if an output function is active it can mess with
> what the irq controller gets.
>
> Think about applying/removing bias if necessary too.
>

Ok, I am trying to add a new pinctrl configuration for
TSIN_A_DIN0 //  TDMB_FS // TDMB_SLV_FS
But it's still not working at my end.

-Anand