[PATCH v4 3/4] arm64: dts: imx8mm-var-som: Add Variscite VAR-SOM-MX8MM System on Module
Krzysztof Kozlowski
krzk at kernel.org
Mon Aug 24 15:18:18 EDT 2020
Add DTSI of Variscite VAR-SOM-MX8MM System on Module in a basic version,
delivered with Variscite Symphony Evaluation kit. This version comes
with:
- 2 GB of RAM,
- 16 GB eMMC,
- Gigabit Ethernet PHY,
- 802.11 ac/a/b/g/n WiFi with 4.2 Bluetooth (Cypress CYW43353),
- CAN bus,
- Audio codec (not yet configured in DTSI).
Signed-off-by: Krzysztof Kozlowski <krzk at kernel.org>
---
Changes since v3:
1. Correct SPI CS polarity,
2. Add suffix "grp" to all pin configuration nodes,
3. Remove unused pcie0grp.
Changes since v2:
1. Remove fsl,spi-num-chipselects,
2. Remove can node (not yet in mainline),
3. Use phy properties instead of deprecated phy-reset-xxx,
4. Remove orphaned pinctrl-names,
5. Use lowercase regulator names to match schema,
6. Use more specific regulator node names.
Changes since v1:
1. None
---
.../boot/dts/freescale/imx8mm-var-som.dtsi | 553 ++++++++++++++++++
1 file changed, 553 insertions(+)
create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-var-som.dtsi
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-var-som.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-var-som.dtsi
new file mode 100644
index 000000000000..c371cb34b3f7
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mm-var-som.dtsi
@@ -0,0 +1,553 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright 2019 NXP
+ * Copyright (C) 2020 Krzysztof Kozlowski <krzk at kernel.org>
+ */
+
+#include "imx8mm.dtsi"
+
+/ {
+ model = "Variscite VAR-SOM-MX8MM module";
+ compatible = "variscite,var-som-mx8mm", "fsl,imx8mm";
+
+ chosen {
+ stdout-path = &uart4;
+ };
+
+ memory at 40000000 {
+ device_type = "memory";
+ reg = <0x0 0x40000000 0 0x80000000>;
+ };
+
+ reg_eth_phy: regulator-eth-phy {
+ compatible = "regulator-fixed";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_reg_eth_phy>;
+ regulator-name = "eth_phy_pwr";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&gpio2 9 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+};
+
+&A53_0 {
+ cpu-supply = <&buck2_reg>;
+};
+
+&A53_1 {
+ cpu-supply = <&buck2_reg>;
+};
+
+&A53_2 {
+ cpu-supply = <&buck2_reg>;
+};
+
+&A53_3 {
+ cpu-supply = <&buck2_reg>;
+};
+
+&ddrc {
+ operating-points-v2 = <&ddrc_opp_table>;
+
+ ddrc_opp_table: opp-table {
+ compatible = "operating-points-v2";
+
+ opp-25M {
+ opp-hz = /bits/ 64 <25000000>;
+ };
+
+ opp-100M {
+ opp-hz = /bits/ 64 <100000000>;
+ };
+
+ opp-750M {
+ opp-hz = /bits/ 64 <750000000>;
+ };
+ };
+};
+
+&ecspi1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi1>;
+ cs-gpios = <&gpio1 14 GPIO_ACTIVE_LOW>,
+ <&gpio1 0 GPIO_ACTIVE_LOW>;
+ /delete-property/ dmas;
+ /delete-property/ dma-names;
+ status = "okay";
+
+ /* Resistive touch controller */
+ touchscreen at 0 {
+ reg = <0>;
+ compatible = "ti,ads7846";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_restouch>;
+ interrupt-parent = <&gpio1>;
+ interrupts = <3 IRQ_TYPE_EDGE_FALLING>;
+
+ spi-max-frequency = <1500000>;
+ pendown-gpio = <&gpio1 3 GPIO_ACTIVE_LOW>;
+
+ ti,x-min = /bits/ 16 <125>;
+ touchscreen-size-x = /bits/ 16 <4008>;
+ ti,y-min = /bits/ 16 <282>;
+ touchscreen-size-y = /bits/ 16 <3864>;
+ ti,x-plate-ohms = /bits/ 16 <180>;
+ touchscreen-max-pressure = /bits/ 16 <255>;
+ touchscreen-average-samples = /bits/ 16 <10>;
+ ti,debounce-tol = /bits/ 16 <3>;
+ ti,debounce-rep = /bits/ 16 <1>;
+ ti,settle-delay-usec = /bits/ 16 <150>;
+ ti,keep-vref-on;
+ wakeup-source;
+ };
+};
+
+&fec1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_fec1>;
+ phy-mode = "rgmii";
+ phy-handle = <ðphy>;
+ phy-supply = <®_eth_phy>;
+ fsl,magic-packet;
+ status = "okay";
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ethphy: ethernet-phy at 4 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <4>;
+ reset-gpios = <&gpio1 9 GPIO_ACTIVE_LOW>;
+ reset-assert-us = <10000>;
+ reset-deassert-us = <10000>;
+ };
+ };
+};
+
+&i2c1 {
+ clock-frequency = <400000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c1>;
+ status = "okay";
+
+ pmic at 4b {
+ compatible = "rohm,bd71847";
+ reg = <0x4b>;
+ pinctrl-0 = <&pinctrl_pmic>;
+ interrupt-parent = <&gpio2>;
+ interrupts = <8 GPIO_ACTIVE_LOW>;
+ rohm,reset-snvs-powered;
+
+ regulators {
+ buck1_reg: BUCK1 {
+ regulator-name = "buck1";
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ regulator-ramp-delay = <1250>;
+ };
+
+ buck2_reg: BUCK2 {
+ regulator-name = "buck2";
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ regulator-ramp-delay = <1250>;
+ rohm,dvs-run-voltage = <1000000>;
+ rohm,dvs-idle-voltage = <900000>;
+ };
+
+ buck3_reg: BUCK3 {
+ regulator-name = "buck3";
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ buck4_reg: BUCK4 {
+ regulator-name = "buck4";
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ buck5_reg: BUCK5 {
+ regulator-name = "buck5";
+ regulator-min-microvolt = <1605000>;
+ regulator-max-microvolt = <1995000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ buck6_reg: BUCK6 {
+ regulator-name = "buck6";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1400000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldo1_reg: LDO1 {
+ regulator-name = "ldo1";
+ regulator-min-microvolt = <1600000>;
+ regulator-max-microvolt = <1900000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldo2_reg: LDO2 {
+ regulator-name = "ldo2";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <900000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldo3_reg: LDO3 {
+ regulator-name = "ldo3";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldo4_reg: LDO4 {
+ regulator-name = "ldo4";
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldo5_reg: LDO5 {
+ regulator-compatible = "ldo5";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
+
+ ldo6_reg: LDO6 {
+ regulator-name = "ldo6";
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+ };
+ };
+};
+
+&i2c3 {
+ clock-frequency = <400000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c3>;
+ status = "okay";
+
+ /* TODO: configure audio, as of now just put a placeholder */
+ wm8904: codec at 1a {
+ compatible = "wlf,wm8904";
+ reg = <0x1a>;
+ status = "disabled";
+ };
+};
+
+&snvs_pwrkey {
+ status = "okay";
+};
+
+/* Bluetooth */
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart2>;
+ assigned-clocks = <&clk IMX8MM_CLK_UART2>;
+ assigned-clock-parents = <&clk IMX8MM_SYS_PLL1_80M>;
+ uart-has-rtscts;
+ status = "okay";
+};
+
+/* Console */
+&uart4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart4>;
+ status = "okay";
+};
+
+&usbotg1 {
+ dr_mode = "otg";
+ usb-role-switch;
+ status = "okay";
+};
+
+&usbotg2 {
+ dr_mode = "otg";
+ usb-role-switch;
+ status = "okay";
+};
+
+/* WIFI */
+&usdhc1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pinctrl-names = "default", "state_100mhz", "state_200mhz";
+ pinctrl-0 = <&pinctrl_usdhc1>;
+ pinctrl-1 = <&pinctrl_usdhc1_100mhz>;
+ pinctrl-2 = <&pinctrl_usdhc1_200mhz>;
+ bus-width = <4>;
+ non-removable;
+ keep-power-in-suspend;
+ status = "okay";
+
+ brcmf: bcrmf at 1 {
+ reg = <1>;
+ compatible = "brcm,bcm4329-fmac";
+ };
+};
+
+/* SD */
+&usdhc2 {
+ assigned-clocks = <&clk IMX8MM_CLK_USDHC2>;
+ assigned-clock-rates = <200000000>;
+ pinctrl-names = "default", "state_100mhz", "state_200mhz";
+ pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>;
+ pinctrl-1 = <&pinctrl_usdhc2_100mhz>, <&pinctrl_usdhc2_gpio>;
+ pinctrl-2 = <&pinctrl_usdhc2_200mhz>, <&pinctrl_usdhc2_gpio>;
+ cd-gpios = <&gpio1 10 GPIO_ACTIVE_LOW>;
+ bus-width = <4>;
+ vmmc-supply = <®_usdhc2_vmmc>;
+ status = "okay";
+};
+
+/* eMMC */
+&usdhc3 {
+ assigned-clocks = <&clk IMX8MM_CLK_USDHC3_ROOT>;
+ assigned-clock-rates = <400000000>;
+ pinctrl-names = "default", "state_100mhz", "state_200mhz";
+ pinctrl-0 = <&pinctrl_usdhc3>;
+ pinctrl-1 = <&pinctrl_usdhc3_100mhz>;
+ pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
+ bus-width = <8>;
+ non-removable;
+ status = "okay";
+};
+
+&wdog1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_wdog>;
+ fsl,ext-reset-output;
+ status = "okay";
+};
+
+&iomuxc {
+ pinctrl_ecspi1: ecspi1grp {
+ fsl,pins = <
+ MX8MM_IOMUXC_ECSPI1_SCLK_ECSPI1_SCLK 0x13
+ MX8MM_IOMUXC_ECSPI1_MOSI_ECSPI1_MOSI 0x13
+ MX8MM_IOMUXC_ECSPI1_MISO_ECSPI1_MISO 0x13
+ MX8MM_IOMUXC_GPIO1_IO14_GPIO1_IO14 0x13
+ MX8MM_IOMUXC_GPIO1_IO00_GPIO1_IO0 0x13
+ >;
+ };
+
+ pinctrl_fec1: fec1grp {
+ fsl,pins = <
+ MX8MM_IOMUXC_ENET_MDC_ENET1_MDC 0x3
+ MX8MM_IOMUXC_ENET_MDIO_ENET1_MDIO 0x3
+ MX8MM_IOMUXC_ENET_TD3_ENET1_RGMII_TD3 0x1f
+ MX8MM_IOMUXC_ENET_TD2_ENET1_RGMII_TD2 0x1f
+ MX8MM_IOMUXC_ENET_TD1_ENET1_RGMII_TD1 0x1f
+ MX8MM_IOMUXC_ENET_TD0_ENET1_RGMII_TD0 0x1f
+ MX8MM_IOMUXC_ENET_RD3_ENET1_RGMII_RD3 0x91
+ MX8MM_IOMUXC_ENET_RD2_ENET1_RGMII_RD2 0x91
+ MX8MM_IOMUXC_ENET_RD1_ENET1_RGMII_RD1 0x91
+ MX8MM_IOMUXC_ENET_RD0_ENET1_RGMII_RD0 0x91
+ MX8MM_IOMUXC_ENET_TXC_ENET1_RGMII_TXC 0x1f
+ MX8MM_IOMUXC_ENET_RXC_ENET1_RGMII_RXC 0x91
+ MX8MM_IOMUXC_ENET_RX_CTL_ENET1_RGMII_RX_CTL 0x91
+ MX8MM_IOMUXC_ENET_TX_CTL_ENET1_RGMII_TX_CTL 0x1f
+ MX8MM_IOMUXC_GPIO1_IO09_GPIO1_IO9 0x19
+ >;
+ };
+
+ pinctrl_i2c1: i2c1grp {
+ fsl,pins = <
+ MX8MM_IOMUXC_I2C1_SCL_I2C1_SCL 0x400001c3
+ MX8MM_IOMUXC_I2C1_SDA_I2C1_SDA 0x400001c3
+ >;
+ };
+
+ pinctrl_i2c3: i2c3grp {
+ fsl,pins = <
+ MX8MM_IOMUXC_I2C3_SCL_I2C3_SCL 0x400001c3
+ MX8MM_IOMUXC_I2C3_SDA_I2C3_SDA 0x400001c3
+ >;
+ };
+
+ pinctrl_pmic: pmicirqgrp {
+ fsl,pins = <
+ MX8MM_IOMUXC_SD1_DATA6_GPIO2_IO8 0x41
+ >;
+ };
+
+ pinctrl_reg_eth_phy: regethphygrp {
+ fsl,pins = <
+ MX8MM_IOMUXC_SD1_DATA7_GPIO2_IO9 0x41
+ >;
+ };
+
+ pinctrl_restouch: restouchgrp {
+ fsl,pins = <
+ MX8MM_IOMUXC_GPIO1_IO03_GPIO1_IO3 0x1c0
+ >;
+ };
+
+ pinctrl_uart2: uart2grp {
+ fsl,pins = <
+ MX8MM_IOMUXC_SAI3_TXFS_UART2_DCE_RX 0x140
+ MX8MM_IOMUXC_SAI3_TXC_UART2_DCE_TX 0x140
+ MX8MM_IOMUXC_SAI3_RXC_UART2_DCE_CTS_B 0x140
+ MX8MM_IOMUXC_SAI3_RXD_UART2_DCE_RTS_B 0x140
+ >;
+ };
+
+ pinctrl_uart4: uart4grp {
+ fsl,pins = <
+ MX8MM_IOMUXC_UART4_RXD_UART4_DCE_RX 0x140
+ MX8MM_IOMUXC_UART4_TXD_UART4_DCE_TX 0x140
+ >;
+ };
+
+ pinctrl_usdhc1: usdhc1grp {
+ fsl,pins = <
+ MX8MM_IOMUXC_SD1_CLK_USDHC1_CLK 0x190
+ MX8MM_IOMUXC_SD1_CMD_USDHC1_CMD 0x1d0
+ MX8MM_IOMUXC_SD1_DATA0_USDHC1_DATA0 0x1d0
+ MX8MM_IOMUXC_SD1_DATA1_USDHC1_DATA1 0x1d0
+ MX8MM_IOMUXC_SD1_DATA2_USDHC1_DATA2 0x1d0
+ MX8MM_IOMUXC_SD1_DATA3_USDHC1_DATA3 0x1d0
+ >;
+ };
+
+ pinctrl_usdhc1_100mhz: usdhc1-100mhzgrp {
+ fsl,pins = <
+ MX8MM_IOMUXC_SD1_CLK_USDHC1_CLK 0x194
+ MX8MM_IOMUXC_SD1_CMD_USDHC1_CMD 0x1d4
+ MX8MM_IOMUXC_SD1_DATA0_USDHC1_DATA0 0x1d4
+ MX8MM_IOMUXC_SD1_DATA1_USDHC1_DATA1 0x1d4
+ MX8MM_IOMUXC_SD1_DATA2_USDHC1_DATA2 0x1d4
+ MX8MM_IOMUXC_SD1_DATA3_USDHC1_DATA3 0x1d4
+ >;
+ };
+
+ pinctrl_usdhc1_200mhz: usdhc1-200mhzgrp {
+ fsl,pins = <
+ MX8MM_IOMUXC_SD1_CLK_USDHC1_CLK 0x196
+ MX8MM_IOMUXC_SD1_CMD_USDHC1_CMD 0x1d6
+ MX8MM_IOMUXC_SD1_DATA0_USDHC1_DATA0 0x1d6
+ MX8MM_IOMUXC_SD1_DATA1_USDHC1_DATA1 0x1d6
+ MX8MM_IOMUXC_SD1_DATA2_USDHC1_DATA2 0x1d6
+ MX8MM_IOMUXC_SD1_DATA3_USDHC1_DATA3 0x1d6
+ >;
+ };
+
+ pinctrl_usdhc2_gpio: usdhc2gpiogrp {
+ fsl,pins = <
+ MX8MM_IOMUXC_GPIO1_IO10_GPIO1_IO10 0xc1
+ >;
+ };
+
+ pinctrl_usdhc2: usdhc2grp {
+ fsl,pins = <
+ MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x190
+ MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d0
+ MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d0
+ MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d0
+ MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d0
+ MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d0
+ MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x1d0
+ >;
+ };
+
+ pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp {
+ fsl,pins = <
+ MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x194
+ MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d4
+ MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d4
+ MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d4
+ MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d4
+ MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d4
+ MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x1d0
+ >;
+ };
+
+ pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp {
+ fsl,pins = <
+ MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x196
+ MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d6
+ MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d6
+ MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d6
+ MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d6
+ MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d6
+ MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x1d0
+ >;
+ };
+
+ pinctrl_usdhc3: usdhc3grp {
+ fsl,pins = <
+ MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK 0x190
+ MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD 0x1d0
+ MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0 0x1d0
+ MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1 0x1d0
+ MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x1d0
+ MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3 0x1d0
+ MX8MM_IOMUXC_NAND_RE_B_USDHC3_DATA4 0x1d0
+ MX8MM_IOMUXC_NAND_CE2_B_USDHC3_DATA5 0x1d0
+ MX8MM_IOMUXC_NAND_CE3_B_USDHC3_DATA6 0x1d0
+ MX8MM_IOMUXC_NAND_CLE_USDHC3_DATA7 0x1d0
+ MX8MM_IOMUXC_NAND_CE1_B_USDHC3_STROBE 0x190
+ >;
+ };
+
+ pinctrl_usdhc3_100mhz: usdhc3-100mhzgrp {
+ fsl,pins = <
+ MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK 0x194
+ MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD 0x1d4
+ MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0 0x1d4
+ MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1 0x1d4
+ MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x1d4
+ MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3 0x1d4
+ MX8MM_IOMUXC_NAND_RE_B_USDHC3_DATA4 0x1d4
+ MX8MM_IOMUXC_NAND_CE2_B_USDHC3_DATA5 0x1d4
+ MX8MM_IOMUXC_NAND_CE3_B_USDHC3_DATA6 0x1d4
+ MX8MM_IOMUXC_NAND_CLE_USDHC3_DATA7 0x1d4
+ MX8MM_IOMUXC_NAND_CE1_B_USDHC3_STROBE 0x194
+ >;
+ };
+
+ pinctrl_usdhc3_200mhz: usdhc3-200mhzgrp {
+ fsl,pins = <
+ MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK 0x196
+ MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD 0x1d6
+ MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0 0x1d6
+ MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1 0x1d6
+ MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x1d6
+ MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3 0x1d6
+ MX8MM_IOMUXC_NAND_RE_B_USDHC3_DATA4 0x1d6
+ MX8MM_IOMUXC_NAND_CE2_B_USDHC3_DATA5 0x1d6
+ MX8MM_IOMUXC_NAND_CE3_B_USDHC3_DATA6 0x1d6
+ MX8MM_IOMUXC_NAND_CLE_USDHC3_DATA7 0x1d6
+ MX8MM_IOMUXC_NAND_CE1_B_USDHC3_STROBE 0x196
+ >;
+ };
+
+ pinctrl_wdog: wdoggrp {
+ fsl,pins = <
+ MX8MM_IOMUXC_GPIO1_IO02_WDOG1_WDOG_B 0xc6
+ >;
+ };
+};
--
2.17.1
More information about the linux-arm-kernel
mailing list