[PATCH v5 6/8] phy: amlogic: Add Amlogic G12A USB3 + PCIE Combo PHY Driver

Kishon Vijay Abraham I kishon at ti.com
Tue Mar 26 00:36:27 PDT 2019



On 25/03/19 3:09 PM, Neil Armstrong wrote:
> This adds support for the shared USB3 + PCIE PHY found in the
> Amlogic G12A SoC Family.
> 
> It supports USB3 Host mode or PCIE 2.0 mode, depending on the layout of
> the board.
> 
> Selection is done by the #phy-cells, making the mode static and exclusive.
> 
> Signed-off-by: Neil Armstrong <narmstrong at baylibre.com>
> Reviewed-by: Martin Blumenstingl <martin.blumenstingl at googlemail.com>

merged 1,2, 5 and 6 patches of this series.

Thanks
Kishon

> ---
>  drivers/phy/amlogic/Kconfig                   |  11 +
>  drivers/phy/amlogic/Makefile                  |   1 +
>  .../phy/amlogic/phy-meson-g12a-usb3-pcie.c    | 413 ++++++++++++++++++
>  3 files changed, 425 insertions(+)
>  create mode 100644 drivers/phy/amlogic/phy-meson-g12a-usb3-pcie.c
> 
> diff --git a/drivers/phy/amlogic/Kconfig b/drivers/phy/amlogic/Kconfig
> index 560ff0f1ed4c..4c08c1ccdd04 100644
> --- a/drivers/phy/amlogic/Kconfig
> +++ b/drivers/phy/amlogic/Kconfig
> @@ -47,3 +47,14 @@ config PHY_MESON_G12A_USB2
>  	  Enable this to support the Meson USB2 PHYs found in Meson
>  	  G12A SoCs.
>  	  If unsure, say N.
> +
> +config PHY_MESON_G12A_USB3_PCIE
> +	tristate "Meson G12A USB3+PCIE Combo PHY driver"
> +	default ARCH_MESON
> +	depends on OF && (ARCH_MESON || COMPILE_TEST)
> +	select GENERIC_PHY
> +	select REGMAP_MMIO
> +	help
> +	  Enable this to support the Meson USB3 + PCIE Combo PHY found
> +	  in Meson G12A SoCs.
> +	  If unsure, say N.
> diff --git a/drivers/phy/amlogic/Makefile b/drivers/phy/amlogic/Makefile
> index 7d4d10f5a6b3..fdd008e1b19b 100644
> --- a/drivers/phy/amlogic/Makefile
> +++ b/drivers/phy/amlogic/Makefile
> @@ -2,3 +2,4 @@ obj-$(CONFIG_PHY_MESON8B_USB2)		+= phy-meson8b-usb2.o
>  obj-$(CONFIG_PHY_MESON_GXL_USB2)	+= phy-meson-gxl-usb2.o
>  obj-$(CONFIG_PHY_MESON_G12A_USB2)	+= phy-meson-g12a-usb2.o
>  obj-$(CONFIG_PHY_MESON_GXL_USB3)	+= phy-meson-gxl-usb3.o
> +obj-$(CONFIG_PHY_MESON_G12A_USB3_PCIE)	+= phy-meson-g12a-usb3-pcie.o
> diff --git a/drivers/phy/amlogic/phy-meson-g12a-usb3-pcie.c b/drivers/phy/amlogic/phy-meson-g12a-usb3-pcie.c
> new file mode 100644
> index 000000000000..6233a7979a93
> --- /dev/null
> +++ b/drivers/phy/amlogic/phy-meson-g12a-usb3-pcie.c
> @@ -0,0 +1,413 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Amlogic G12A USB3 + PCIE Combo PHY driver
> + *
> + * Copyright (C) 2017 Amlogic, Inc. All rights reserved
> + * Copyright (C) 2019 BayLibre, SAS
> + * Author: Neil Armstrong <narmstrong at baylibre.com>
> + */
> +
> +#include <linux/bitfield.h>
> +#include <linux/bitops.h>
> +#include <linux/clk.h>
> +#include <linux/module.h>
> +#include <linux/of_device.h>
> +#include <linux/phy/phy.h>
> +#include <linux/regmap.h>
> +#include <linux/reset.h>
> +#include <linux/platform_device.h>
> +#include <dt-bindings/phy/phy.h>
> +
> +#define PHY_R0							0x00
> +	#define PHY_R0_PCIE_POWER_STATE				GENMASK(4, 0)
> +	#define PHY_R0_PCIE_USB3_SWITCH				GENMASK(6, 5)
> +
> +#define PHY_R1							0x04
> +	#define PHY_R1_PHY_TX1_TERM_OFFSET			GENMASK(4, 0)
> +	#define PHY_R1_PHY_TX0_TERM_OFFSET			GENMASK(9, 5)
> +	#define PHY_R1_PHY_RX1_EQ				GENMASK(12, 10)
> +	#define PHY_R1_PHY_RX0_EQ				GENMASK(15, 13)
> +	#define PHY_R1_PHY_LOS_LEVEL				GENMASK(20, 16)
> +	#define PHY_R1_PHY_LOS_BIAS				GENMASK(23, 21)
> +	#define PHY_R1_PHY_REF_CLKDIV2				BIT(24)
> +	#define PHY_R1_PHY_MPLL_MULTIPLIER			GENMASK(31, 25)
> +
> +#define PHY_R2							0x08
> +	#define PHY_R2_PCS_TX_DEEMPH_GEN2_6DB			GENMASK(5, 0)
> +	#define PHY_R2_PCS_TX_DEEMPH_GEN2_3P5DB			GENMASK(11, 6)
> +	#define PHY_R2_PCS_TX_DEEMPH_GEN1			GENMASK(17, 12)
> +	#define PHY_R2_PHY_TX_VBOOST_LVL			GENMASK(20, 18)
> +
> +#define PHY_R4							0x10
> +	#define PHY_R4_PHY_CR_WRITE				BIT(0)
> +	#define PHY_R4_PHY_CR_READ				BIT(1)
> +	#define PHY_R4_PHY_CR_DATA_IN				GENMASK(17, 2)
> +	#define PHY_R4_PHY_CR_CAP_DATA				BIT(18)
> +	#define PHY_R4_PHY_CR_CAP_ADDR				BIT(19)
> +
> +#define PHY_R5							0x14
> +	#define PHY_R5_PHY_CR_DATA_OUT				GENMASK(15, 0)
> +	#define PHY_R5_PHY_CR_ACK				BIT(16)
> +	#define PHY_R5_PHY_BS_OUT				BIT(17)
> +
> +struct phy_g12a_usb3_pcie_priv {
> +	struct regmap		*regmap;
> +	struct regmap		*regmap_cr;
> +	struct clk		*clk_ref;
> +	struct reset_control	*reset;
> +	struct phy		*phy;
> +	unsigned int		mode;
> +};
> +
> +static const struct regmap_config phy_g12a_usb3_pcie_regmap_conf = {
> +	.reg_bits = 8,
> +	.val_bits = 32,
> +	.reg_stride = 4,
> +	.max_register = PHY_R5,
> +};
> +
> +static int phy_g12a_usb3_pcie_cr_bus_addr(struct phy_g12a_usb3_pcie_priv *priv,
> +					  unsigned int addr)
> +{
> +	unsigned int val, reg;
> +	int ret;
> +
> +	reg = FIELD_PREP(PHY_R4_PHY_CR_DATA_IN, addr);
> +
> +	regmap_write(priv->regmap, PHY_R4, reg);
> +	regmap_write(priv->regmap, PHY_R4, reg);
> +
> +	regmap_write(priv->regmap, PHY_R4, reg | PHY_R4_PHY_CR_CAP_ADDR);
> +
> +	ret = regmap_read_poll_timeout(priv->regmap, PHY_R5, val,
> +				       (val & PHY_R5_PHY_CR_ACK),
> +				       5, 1000);
> +	if (ret)
> +		return ret;
> +
> +	regmap_write(priv->regmap, PHY_R4, reg);
> +
> +	ret = regmap_read_poll_timeout(priv->regmap, PHY_R5, val,
> +				       !(val & PHY_R5_PHY_CR_ACK),
> +				       5, 1000);
> +	if (ret)
> +		return ret;
> +
> +	return 0;
> +}
> +
> +static int phy_g12a_usb3_pcie_cr_bus_read(void *context, unsigned int addr,
> +					  unsigned int *data)
> +{
> +	struct phy_g12a_usb3_pcie_priv *priv = context;
> +	unsigned int val;
> +	int ret;
> +
> +	ret = phy_g12a_usb3_pcie_cr_bus_addr(priv, addr);
> +	if (ret)
> +		return ret;
> +
> +	regmap_write(priv->regmap, PHY_R4, 0);
> +	regmap_write(priv->regmap, PHY_R4, PHY_R4_PHY_CR_READ);
> +
> +	ret = regmap_read_poll_timeout(priv->regmap, PHY_R5, val,
> +				       (val & PHY_R5_PHY_CR_ACK),
> +				       5, 1000);
> +	if (ret)
> +		return ret;
> +
> +	*data = FIELD_GET(PHY_R5_PHY_CR_DATA_OUT, val);
> +
> +	regmap_write(priv->regmap, PHY_R4, 0);
> +
> +	ret = regmap_read_poll_timeout(priv->regmap, PHY_R5, val,
> +				       !(val & PHY_R5_PHY_CR_ACK),
> +				       5, 1000);
> +	if (ret)
> +		return ret;
> +
> +	return 0;
> +}
> +
> +static int phy_g12a_usb3_pcie_cr_bus_write(void *context, unsigned int addr,
> +					   unsigned int data)
> +{
> +	struct phy_g12a_usb3_pcie_priv *priv = context;
> +	unsigned int val, reg;
> +	int ret;
> +
> +	ret = phy_g12a_usb3_pcie_cr_bus_addr(priv, addr);
> +	if (ret)
> +		return ret;
> +
> +	reg = FIELD_PREP(PHY_R4_PHY_CR_DATA_IN, data);
> +
> +	regmap_write(priv->regmap, PHY_R4, reg);
> +	regmap_write(priv->regmap, PHY_R4, reg);
> +
> +	regmap_write(priv->regmap, PHY_R4, reg | PHY_R4_PHY_CR_CAP_DATA);
> +
> +	ret = regmap_read_poll_timeout(priv->regmap, PHY_R5, val,
> +				       (val & PHY_R5_PHY_CR_ACK),
> +				       5, 1000);
> +	if (ret)
> +		return ret;
> +
> +	regmap_write(priv->regmap, PHY_R4, reg);
> +
> +	ret = regmap_read_poll_timeout(priv->regmap, PHY_R5, val,
> +				       (val & PHY_R5_PHY_CR_ACK) == 0,
> +				       5, 1000);
> +	if (ret)
> +		return ret;
> +
> +	regmap_write(priv->regmap, PHY_R4, reg);
> +
> +	regmap_write(priv->regmap, PHY_R4, reg | PHY_R4_PHY_CR_WRITE);
> +
> +	ret = regmap_read_poll_timeout(priv->regmap, PHY_R5, val,
> +				       (val & PHY_R5_PHY_CR_ACK),
> +				       5, 1000);
> +	if (ret)
> +		return ret;
> +
> +	regmap_write(priv->regmap, PHY_R4, reg);
> +
> +	ret = regmap_read_poll_timeout(priv->regmap, PHY_R5, val,
> +				       (val & PHY_R5_PHY_CR_ACK) == 0,
> +				       5, 1000);
> +	if (ret)
> +		return ret;
> +
> +	return 0;
> +}
> +
> +static const struct regmap_config phy_g12a_usb3_pcie_cr_regmap_conf = {
> +	.reg_bits = 16,
> +	.val_bits = 16,
> +	.reg_read = phy_g12a_usb3_pcie_cr_bus_read,
> +	.reg_write = phy_g12a_usb3_pcie_cr_bus_write,
> +	.max_register = 0xffff,
> +	.fast_io = true,
> +};
> +
> +static int phy_g12a_usb3_init(struct phy *phy)
> +{
> +	struct phy_g12a_usb3_pcie_priv *priv = phy_get_drvdata(phy);
> +	int data, ret;
> +
> +	/* Switch PHY to USB3 */
> +	/* TODO figure out how to handle when PCIe was set in the bootloader */
> +	regmap_update_bits(priv->regmap, PHY_R0,
> +			   PHY_R0_PCIE_USB3_SWITCH,
> +			   PHY_R0_PCIE_USB3_SWITCH);
> +
> +	/*
> +	 * WORKAROUND: There is SSPHY suspend bug due to
> +	 * which USB enumerates
> +	 * in HS mode instead of SS mode. Workaround it by asserting
> +	 * LANE0.TX_ALT_BLOCK.EN_ALT_BUS to enable TX to use alt bus
> +	 * mode
> +	 */
> +	ret = regmap_update_bits(priv->regmap_cr, 0x102d, BIT(7), BIT(7));
> +	if (ret)
> +		return ret;
> +
> +	ret = regmap_update_bits(priv->regmap_cr, 0x1010, 0xff0, 20);
> +	if (ret)
> +		return ret;
> +
> +	/*
> +	 * Fix RX Equalization setting as follows
> +	 * LANE0.RX_OVRD_IN_HI. RX_EQ_EN set to 0
> +	 * LANE0.RX_OVRD_IN_HI.RX_EQ_EN_OVRD set to 1
> +	 * LANE0.RX_OVRD_IN_HI.RX_EQ set to 3
> +	 * LANE0.RX_OVRD_IN_HI.RX_EQ_OVRD set to 1
> +	 */
> +	ret = regmap_read(priv->regmap_cr, 0x1006, &data);
> +	if (ret)
> +		return ret;
> +
> +	data &= ~BIT(6);
> +	data |= BIT(7);
> +	data &= ~(0x7 << 8);
> +	data |= (0x3 << 8);
> +	data |= (1 << 11);
> +	ret = regmap_write(priv->regmap_cr, 0x1006, data);
> +	if (ret)
> +		return ret;
> +
> +	/*
> +	 * Set EQ and TX launch amplitudes as follows
> +	 * LANE0.TX_OVRD_DRV_LO.PREEMPH set to 22
> +	 * LANE0.TX_OVRD_DRV_LO.AMPLITUDE set to 127
> +	 * LANE0.TX_OVRD_DRV_LO.EN set to 1.
> +	 */
> +	ret = regmap_read(priv->regmap_cr, 0x1002, &data);
> +	if (ret)
> +		return ret;
> +
> +	data &= ~0x3f80;
> +	data |= (0x16 << 7);
> +	data &= ~0x7f;
> +	data |= (0x7f | BIT(14));
> +	ret = regmap_write(priv->regmap_cr, 0x1002, data);
> +	if (ret)
> +		return ret;
> +
> +	/* MPLL_LOOP_CTL.PROP_CNTRL = 8 */
> +	ret = regmap_update_bits(priv->regmap_cr, 0x30, 0xf << 4, 8 << 4);
> +	if (ret)
> +		return ret;
> +
> +	regmap_update_bits(priv->regmap, PHY_R2,
> +			PHY_R2_PHY_TX_VBOOST_LVL,
> +			FIELD_PREP(PHY_R2_PHY_TX_VBOOST_LVL, 0x4));
> +
> +	regmap_update_bits(priv->regmap, PHY_R1,
> +			PHY_R1_PHY_LOS_BIAS | PHY_R1_PHY_LOS_LEVEL,
> +			FIELD_PREP(PHY_R1_PHY_LOS_BIAS, 4) |
> +			FIELD_PREP(PHY_R1_PHY_LOS_LEVEL, 9));
> +
> +	return 0;
> +}
> +
> +static int phy_g12a_usb3_pcie_init(struct phy *phy)
> +{
> +	struct phy_g12a_usb3_pcie_priv *priv = phy_get_drvdata(phy);
> +	int ret;
> +
> +	ret = reset_control_reset(priv->reset);
> +	if (ret)
> +		return ret;
> +
> +	if (priv->mode == PHY_TYPE_USB3)
> +		return phy_g12a_usb3_init(phy);
> +
> +	/* Power UP PCIE */
> +	/* TODO figure out when the bootloader has set USB3 mode before */
> +	regmap_update_bits(priv->regmap, PHY_R0,
> +			   PHY_R0_PCIE_POWER_STATE,
> +			   FIELD_PREP(PHY_R0_PCIE_POWER_STATE, 0x1c));
> +
> +	return 0;
> +}
> +
> +static int phy_g12a_usb3_pcie_exit(struct phy *phy)
> +{
> +	struct phy_g12a_usb3_pcie_priv *priv = phy_get_drvdata(phy);
> +
> +	return reset_control_reset(priv->reset);
> +}
> +
> +static struct phy *phy_g12a_usb3_pcie_xlate(struct device *dev,
> +					    struct of_phandle_args *args)
> +{
> +	struct phy_g12a_usb3_pcie_priv *priv = dev_get_drvdata(dev);
> +	unsigned int mode;
> +
> +	if (args->args_count < 1) {
> +		dev_err(dev, "invalid number of arguments\n");
> +		return ERR_PTR(-EINVAL);
> +	}
> +
> +	mode = args->args[0];
> +
> +	if (mode != PHY_TYPE_USB3 && mode != PHY_TYPE_PCIE) {
> +		dev_err(dev, "invalid phy mode select argument\n");
> +		return ERR_PTR(-EINVAL);
> +	}
> +
> +	priv->mode = mode;
> +
> +	return priv->phy;
> +}
> +
> +static const struct phy_ops phy_g12a_usb3_pcie_ops = {
> +	.init		= phy_g12a_usb3_pcie_init,
> +	.exit		= phy_g12a_usb3_pcie_exit,
> +	.owner		= THIS_MODULE,
> +};
> +
> +static int phy_g12a_usb3_pcie_probe(struct platform_device *pdev)
> +{
> +	struct device *dev = &pdev->dev;
> +	struct device_node *np = dev->of_node;
> +	struct phy_g12a_usb3_pcie_priv *priv;
> +	struct resource *res;
> +	struct phy_provider *phy_provider;
> +	void __iomem *base;
> +	int ret;
> +
> +	priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
> +	if (!priv)
> +		return -ENOMEM;
> +
> +	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> +	base = devm_ioremap_resource(dev, res);
> +	if (IS_ERR(base))
> +		return PTR_ERR(base);
> +
> +	priv->regmap = devm_regmap_init_mmio(dev, base,
> +					     &phy_g12a_usb3_pcie_regmap_conf);
> +	if (IS_ERR(priv->regmap))
> +		return PTR_ERR(priv->regmap);
> +
> +	priv->regmap_cr = devm_regmap_init(dev, NULL, priv,
> +					   &phy_g12a_usb3_pcie_cr_regmap_conf);
> +	if (IS_ERR(priv->regmap_cr))
> +		return PTR_ERR(priv->regmap_cr);
> +
> +	priv->clk_ref = devm_clk_get(dev, "ref_clk");
> +	if (IS_ERR(priv->clk_ref))
> +		return PTR_ERR(priv->clk_ref);
> +
> +	ret = clk_prepare_enable(priv->clk_ref);
> +	if (ret)
> +		goto err_disable_clk_ref;
> +
> +	priv->reset = devm_reset_control_array_get(dev, false, false);
> +	if (IS_ERR(priv->reset))
> +		return PTR_ERR(priv->reset);
> +
> +	priv->phy = devm_phy_create(dev, np, &phy_g12a_usb3_pcie_ops);
> +	if (IS_ERR(priv->phy)) {
> +		ret = PTR_ERR(priv->phy);
> +		if (ret != -EPROBE_DEFER)
> +			dev_err(dev, "failed to create PHY\n");
> +
> +		return ret;
> +	}
> +
> +	phy_set_drvdata(priv->phy, priv);
> +	dev_set_drvdata(dev, priv);
> +
> +	phy_provider = devm_of_phy_provider_register(dev,
> +						     phy_g12a_usb3_pcie_xlate);
> +
> +	return PTR_ERR_OR_ZERO(phy_provider);
> +
> +err_disable_clk_ref:
> +	clk_disable_unprepare(priv->clk_ref);
> +
> +	return ret;
> +}
> +
> +static const struct of_device_id phy_g12a_usb3_pcie_of_match[] = {
> +	{ .compatible = "amlogic,g12a-usb3-pcie-phy", },
> +	{ },
> +};
> +MODULE_DEVICE_TABLE(of, phy_g12a_usb3_pcie_of_match);
> +
> +static struct platform_driver phy_g12a_usb3_pcie_driver = {
> +	.probe	= phy_g12a_usb3_pcie_probe,
> +	.driver	= {
> +		.name		= "phy-g12a-usb3-pcie",
> +		.of_match_table	= phy_g12a_usb3_pcie_of_match,
> +	},
> +};
> +module_platform_driver(phy_g12a_usb3_pcie_driver);
> +
> +MODULE_AUTHOR("Neil Armstrong <narmstrong at baylibre.com>");
> +MODULE_DESCRIPTION("Amlogic G12A USB3 + PCIE Combo PHY driver");
> +MODULE_LICENSE("GPL v2");
> 



More information about the linux-arm-kernel mailing list