[PATCH V2 16/27] mmc: mmci: add datactrl block size variant property

Ludovic Barre ludovic.Barre at st.com
Fri Sep 21 02:46:10 PDT 2018


From: Ludovic Barre <ludovic.barre at st.com>

This patch allows to define a datactrl block size
by variant, requested by STM32 sdmmc variant.

Signed-off-by: Ludovic Barre <ludovic.barre at st.com>
---
 drivers/mmc/host/mmci.c | 13 +++++++++++--
 drivers/mmc/host/mmci.h |  2 ++
 2 files changed, 13 insertions(+), 2 deletions(-)

diff --git a/drivers/mmc/host/mmci.c b/drivers/mmc/host/mmci.c
index 9d93fe7..e2272c7 100644
--- a/drivers/mmc/host/mmci.c
+++ b/drivers/mmc/host/mmci.c
@@ -52,6 +52,7 @@ static struct variant_data variant_arm = {
 	.fifosize		= 16 * 4,
 	.fifohalfsize		= 8 * 4,
 	.datalength_bits	= 16,
+	.datactrl_blocksz	= 11,
 	.pwrreg_powerup		= MCI_PWR_UP,
 	.f_max			= 100000000,
 	.reversed_irq_handling	= true,
@@ -65,6 +66,7 @@ static struct variant_data variant_arm_extended_fifo = {
 	.fifosize		= 128 * 4,
 	.fifohalfsize		= 64 * 4,
 	.datalength_bits	= 16,
+	.datactrl_blocksz	= 11,
 	.pwrreg_powerup		= MCI_PWR_UP,
 	.f_max			= 100000000,
 	.mmcimask1		= true,
@@ -78,6 +80,7 @@ static struct variant_data variant_arm_extended_fifo_hwfc = {
 	.fifohalfsize		= 64 * 4,
 	.clkreg_enable		= MCI_ARM_HWFCEN,
 	.datalength_bits	= 16,
+	.datactrl_blocksz	= 11,
 	.pwrreg_powerup		= MCI_PWR_UP,
 	.f_max			= 100000000,
 	.mmcimask1		= true,
@@ -92,6 +95,7 @@ static struct variant_data variant_u300 = {
 	.clkreg_enable		= MCI_ST_U300_HWFCEN,
 	.clkreg_8bit_bus_enable = MCI_ST_8BIT_BUS,
 	.datalength_bits	= 16,
+	.datactrl_blocksz	= 11,
 	.datactrl_mask_sdio	= MCI_DPSM_ST_SDIOEN,
 	.st_sdio			= true,
 	.pwrreg_powerup		= MCI_PWR_ON,
@@ -111,6 +115,7 @@ static struct variant_data variant_nomadik = {
 	.clkreg			= MCI_CLK_ENABLE,
 	.clkreg_8bit_bus_enable = MCI_ST_8BIT_BUS,
 	.datalength_bits	= 24,
+	.datactrl_blocksz	= 11,
 	.datactrl_mask_sdio	= MCI_DPSM_ST_SDIOEN,
 	.st_sdio		= true,
 	.st_clkdiv		= true,
@@ -133,6 +138,7 @@ static struct variant_data variant_ux500 = {
 	.clkreg_8bit_bus_enable = MCI_ST_8BIT_BUS,
 	.clkreg_neg_edge_enable	= MCI_ST_UX500_NEG_EDGE,
 	.datalength_bits	= 24,
+	.datactrl_blocksz	= 11,
 	.datactrl_mask_sdio	= MCI_DPSM_ST_SDIOEN,
 	.st_sdio		= true,
 	.st_clkdiv		= true,
@@ -160,6 +166,7 @@ static struct variant_data variant_ux500v2 = {
 	.clkreg_neg_edge_enable	= MCI_ST_UX500_NEG_EDGE,
 	.datactrl_mask_ddrmode	= MCI_DPSM_ST_DDRMODE,
 	.datalength_bits	= 24,
+	.datactrl_blocksz	= 11,
 	.datactrl_mask_sdio	= MCI_DPSM_ST_SDIOEN,
 	.st_sdio		= true,
 	.st_clkdiv		= true,
@@ -187,6 +194,7 @@ static struct variant_data variant_stm32 = {
 	.clkreg_8bit_bus_enable = MCI_ST_8BIT_BUS,
 	.clkreg_neg_edge_enable	= MCI_ST_UX500_NEG_EDGE,
 	.datalength_bits	= 24,
+	.datactrl_blocksz	= 11,
 	.datactrl_mask_sdio	= MCI_DPSM_ST_SDIOEN,
 	.st_sdio		= true,
 	.st_clkdiv		= true,
@@ -208,6 +216,7 @@ static struct variant_data variant_qcom = {
 	.data_cmd_enable	= MCI_CPSM_QCOM_DATCMD,
 	.blksz_datactrl4	= true,
 	.datalength_bits	= 24,
+	.datactrl_blocksz	= 11,
 	.pwrreg_powerup		= MCI_PWR_UP,
 	.f_max			= 208000000,
 	.explicit_mclk_control	= true,
@@ -1840,13 +1849,13 @@ static int mmci_probe(struct amba_device *dev,
 	/*
 	 * Block size can be up to 2048 bytes, but must be a power of two.
 	 */
-	mmc->max_blk_size = 1 << 11;
+	mmc->max_blk_size = 1 << variant->datactrl_blocksz;
 
 	/*
 	 * Limit the number of blocks transferred so that we don't overflow
 	 * the maximum request size.
 	 */
-	mmc->max_blk_count = mmc->max_req_size >> 11;
+	mmc->max_blk_count = mmc->max_req_size >> variant->datactrl_blocksz;
 
 	spin_lock_init(&host->lock);
 
diff --git a/drivers/mmc/host/mmci.h b/drivers/mmc/host/mmci.h
index 44e06bb..46c8862 100644
--- a/drivers/mmc/host/mmci.h
+++ b/drivers/mmc/host/mmci.h
@@ -217,6 +217,7 @@ struct mmci_host;
  * @blksz_datactrl4: true if Block size is at b4..b16 position in datactrl
  *		     register
  * @datactrl_mask_sdio: SDIO enable mask in datactrl register
+ * @datactrl_blksz: block size in power of two
  * @pwrreg_powerup: power up value for MMCIPOWER register
  * @f_max: maximum clk frequency supported by the controller.
  * @signal_direction: input/out direction of bus signals can be indicated
@@ -248,6 +249,7 @@ struct variant_data {
 	unsigned int		data_cmd_enable;
 	unsigned int		datactrl_mask_ddrmode;
 	unsigned int		datactrl_mask_sdio;
+	unsigned int		datactrl_blocksz;
 	bool			st_sdio;
 	bool			st_clkdiv;
 	bool			blksz_datactrl16;
-- 
2.7.4




More information about the linux-arm-kernel mailing list