[PATCH V12 00/14] Krait clocks + Krait CPUfreq

Craig ctatlor97 at gmail.com
Thu Sep 20 07:27:21 PDT 2018



On 20 September 2018 14:01:57 BST, Sricharan R <sricharan at codeaurora.org> wrote:
>
>
>On 9/20/2018 1:54 AM, Craig wrote:
>> Yup, this patch seems to have fixed the higher frequencies from the
>quick test I did.
>> 
>  Thanks !!. Can i take that as Craig Tatlor <ctatlor97 at gmail.com> ?
Sure, no problem
>
>Regards,
> Sricharan
>
>       tested-by: 
>> On 7 September 2018 15:28:53 BST, Craig Tatlor <ctatlor97 at gmail.com>
>wrote:
>>>
>>>
>>> On 7 September 2018 10:57:34 BST, Sricharan R
>>> <sricharan at codeaurora.org> wrote:
>>>> Hi Craig,
>>>>
>>>>
>>>>>> [v12]
>>>>>>   * Added my signed-off that was missing in some patches.
>>>>>>   * Added Bjorn's acked that i missed earlier.
>>>>>>
>>>>>
>>>>>   Can you give this a try on your 8974 device and check if the
>>>>>   pvs version reporting, scaling for higher frequencies are fine ?
>>>>>   Sorry, i could not get hold of a 8974 device. So in-case if you
>>>> still
>>>>>   have the issues with higher frequencies, can you give a quick
>>> debug
>>>>>   and report. That would be of great help.
>>>>>
>>>>   Ping on this ..
>>>
>>> Hi, didn't see your last message,
>>>
>>> Will have a try on mine in the weekend and report back.
>>>>
>>>> Regards,
>>>> Sricharan
>>>>
>>>>> Regards,
>>>>>  Sricharan
>>>>>
>>>>>
>>>>>> [v11]
>>>>>>   * Dropped patch 13 and 14 from v10 and
>>>>>>     merged the qcom-cpufreq-krait driver to the existing
>>>> qcom-cpufreq-kryo.c
>>>>>>   * Rebased on top of clk-next
>>>>>>   * Fixed a bug while populating the pvs version for krait.
>>>>>>
>>>>>> [v10]
>>>>>>   * Addressed Stephen's comments to add clocks bindings
>properties
>>>>>>     to the newly introduced nodes.
>>>>>>   * Added a change to include opp-supported-hw to qcom-cpufreq.c
>>>>>>   * Rebased on top of clk-next
>>>>>>   * Although there were minor changes to bindings and the driver
>>>>>>     retained the acked-by tags from Rob and Viresh respectively. 
> 
>>>
>>>>>>
>>>>>> [v9]
>>>>>>   * Fixed a rebase issue in Makefile and added Tag from Robh.
>>>>>>
>>>>>> [v8]
>>>>>>   * Fixed a bug in path#14 pointed out by Viresh and also added
>>>> tags.
>>>>>>     No change in any other patch.
>>>>>>
>>>>>> [v7]
>>>>>>   * Fixed comments from Viresh for cleaning up the error handling
>>>>>>     in qcom-cpufreq.c. Also changed the init function to lateinit
>>>>>>     call. This is required because nvmem which gets initialised
>>> with
>>>>>>     module_init needs to go first.
>>>>>>   * Fixed Rob's comments for bindings documentation
>>>>>>   * Fixed kbuild build issue in clk-lpc32xx.c
>>>>>>   * Rebased on top of clk-next
>>>>>>
>>>>>> [v6]
>>>>>>   * Adrressed comments from Viresh for patch #14 in v5 [5]
>>>>>>   * Introduced a new binding operating-points-v2-krait-cpu
>>>>>>     as per discussion with Rob
>>>>>>   * Added Review tags
>>>>>>
>>>>>> [v5]
>>>>>>   * Addressed comments from Rob for bindings
>>>>>>   * Addressed comments from Viresh to use
>dev_pm_opp_set_prop_name,
>>>> accordingly
>>>>>>     dropped patch #12 and corrected patch #11 from previous patch
>>>> set in [4]
>>>>>>   * Converted to use #spdx tags for newly introduced files
>>>>>>
>>>>>> Mostly a resend of the v3 posted by Stephen quite some time back
>>> [1]
>>>>>> except for few changes.
>>>>>>   Based on reading some feedback from list,
>>>>>>   * Dropped the patch "clk: Add safe switch hook" from v3 [2].
>>>>>>     Now this is taken care by patch#10 in this series only for
>>>> Krait.
>>>>>>   * Dropped the path "clk: Avoid sending high rates to downstream
>>>>>> 		      clocks during set_rate" from v3 [3].
>>>>>>   * Rebased on top of clk-next.
>>>>>>   * Dropped the DT update from the series. Will send separately
>>>>>>   * Now with cpufreq-dt+opp supporting voltage scaling,
>registering
>>>> the
>>>>>>     krait cpu supplies in DT should be sufficient. But one issue
>>> is,
>>>>>>     the qcom-cpufreq drivers reads the efuse and based on that
>>>> registers
>>>>>>     the opp data and then registers the cpufreq-dt device. So
>when
>>>>>>     cpufreq-dt driver probes and registers the regulator to the
>OPP
>>>> framework,
>>>>>>     it expects that the opp data for the device should not be
>>>> registered before
>>>>>>     the regulator. Will send a RFC patch removing that check, to
>>>> find out the
>>>>>>     right way of doing it.
>>>>>>
>>>>>> These patches provide cpufreq scaling on devices with Krait CPUs.
>>>>>> In Krait CPU designs there's one PLL and two muxes per CPU,
>>> allowing
>>>>>> us to switch CPU frequencies independently.
>>>>>>
>>>>>> 				 secondary
>>>>>> 	 +-----+                    +
>>>>>> 	 | QSB |-------+------------|\
>>>>>> 	 +-----+       |            | |-+
>>>>>> 		       |    +-------|/  |
>>>>>> 		       |    |       +   |
>>>>>> 	 +-----+       |    |           |
>>>>>> 	 | PLL |----+-------+           |   primary
>>>>>> 	 +-----+    |  |                |     +
>>>>>> 		    |  |                +-----|\       +------+
>>>>>> 	 +-------+  |  |                      | \      |      |
>>>>>> 	 | HFPLL |----------+-----------------|  |-----| CPU0 |
>>>>>> 	 +-------+  |  |    |                 |  |     |      |
>>>>>> 		    |  |    | +-----+         | /      +------+
>>>>>> 		    |  |    +-| / 2 |---------|/
>>>>>> 		    |  |      +-----+         +
>>>>>> 		    |  |         secondary
>>>>>> 		    |  |            +
>>>>>> 		    |  +------------|\
>>>>>> 		    |               | |-+
>>>>>> 		    +---------------|/  |   primary
>>>>>> 				    +   |     +
>>>>>> 					+-----|\       +------+
>>>>>> 	 +-------+                            | \      |      |
>>>>>> 	 | HFPLL |----------------------------|  |-----| CPU1 |
>>>>>> 	 +-------+          |                 |  |     |      |
>>>>>> 			    | +-----+         | /      +------+
>>>>>> 			    +-| / 2 |---------|/
>>>>>> 			      +-----+         +
>>>>>>
>>>>>> To support this in the common clock framework we model the muxes,
>>>>>> dividers, and PLLs as different clocks. CPUfreq only interacts
>>>>>> with the primary mux (farthest right in the diagram). When
>CPUfreq
>>>>>> sets a rate, the mux code finds the best parent that can provide
>>> the
>>>> rate.
>>>>>> Due to the design, QSB and the top PLL are always a fixed rate
>and
>>>> thus
>>>>>> only support one frequency each. These sources provide the lowest
>>>>>> frequencies for the CPUs. The HFPLLs are where we can make the
>CPU
>>>> go
>>>>>> faster (GHz range). Sometimes we need to run the HFPLL twice as
>>>>>> fast and divide it by two to get a particular frequency.
>>>>>>
>>>>>> When switching rates we can't leave the CPU clocked by the HFPLL
>>>> because
>>>>>> we need to turn off the output of the PLL when changing its
>>>> frequency.
>>>>>> This means we have to switch over to the secondary mux and use
>one
>>>> of the
>>>>>> fixed sources. This is why we need something like the safe parent
>>>> patch.
>>>>>>
>>>>>> [1]
>>>>
>http://lists.infradead.org/pipermail/linux-arm-kernel/2015-March/332607.html
>>>>>> [2]
>>>>
>http://lists.infradead.org/pipermail/linux-arm-kernel/2015-March/332615.html
>>>>>> [3]
>>>>
>http://lists.infradead.org/pipermail/linux-arm-kernel/2015-March/332608.html
>>>>>> [4] https://lwn.net/Articles/740994/ 
>>>>>> [5] https://lkml.org/lkml/2017/12/19/537
>>>>>>
>>>>>>
>>>>>> Sricharan R (3):
>>>>>>   clk: qcom: Add safe switch hook for krait mux clocks
>>>>>>   cpufreq: qcom: Re-organise kryo cpufreq to use it for other
>nvmem
>>>>>>     based qcom socs
>>>>>>   cpufreq: qcom: Add support for krait based socs
>>>>>>
>>>>>> Stephen Boyd (11):
>>>>>>   ARM: Add Krait L2 register accessor functions
>>>>>>   clk: qcom: Add support for High-Frequency PLLs (HFPLLs)
>>>>>>   clk: qcom: Add HFPLL driver
>>>>>>   dt-bindings: clock: Document qcom,hfpll
>>>>>>   clk: qcom: Add MSM8960/APQ8064's HFPLLs
>>>>>>   clk: qcom: Add IPQ806X's HFPLLs
>>>>>>   clk: qcom: Add support for Krait clocks
>>>>>>   clk: qcom: Add KPSS ACC/GCC driver
>>>>>>   dt-bindings: arm: Document qcom,kpss-gcc
>>>>>>   clk: qcom: Add Krait clock controller driver
>>>>>>   dt-bindings: clock: Document qcom,krait-cc
>>>>>>
>>>>>>  .../devicetree/bindings/arm/msm/qcom,kpss-acc.txt  |  19 +
>>>>>>  .../devicetree/bindings/arm/msm/qcom,kpss-gcc.txt  |  44 +++
>>>>>>  .../devicetree/bindings/clock/qcom,hfpll.txt       |  60 ++++
>>>>>>  .../devicetree/bindings/clock/qcom,krait-cc.txt    |  34 ++
>>>>>>  .../{kryo-cpufreq.txt => qcom-nvmem-cpufreq.txt}   |   7 +-
>>>>>>  arch/arm/common/Kconfig                            |   3 +
>>>>>>  arch/arm/common/Makefile                           |   1 +
>>>>>>  arch/arm/common/krait-l2-accessors.c               |  48 +++
>>>>>>  arch/arm/include/asm/krait-l2-accessors.h          |   9 +
>>>>>>  drivers/clk/qcom/Kconfig                           |  28 ++
>>>>>>  drivers/clk/qcom/Makefile                          |   5 +
>>>>>>  drivers/clk/qcom/clk-hfpll.c                       | 244
>>>> +++++++++++++
>>>>>>  drivers/clk/qcom/clk-hfpll.h                       |  44 +++
>>>>>>  drivers/clk/qcom/clk-krait.c                       | 126 +++++++
>>>>>>  drivers/clk/qcom/clk-krait.h                       |  40 +++
>>>>>>  drivers/clk/qcom/gcc-ipq806x.c                     |  82 +++++
>>>>>>  drivers/clk/qcom/gcc-msm8960.c                     | 172
>+++++++++
>>>>>>  drivers/clk/qcom/hfpll.c                           |  96 +++++
>>>>>>  drivers/clk/qcom/kpss-xcc.c                        |  87 +++++
>>>>>>  drivers/clk/qcom/krait-cc.c                        | 397
>>>> +++++++++++++++++++++
>>>>>>  drivers/cpufreq/Kconfig.arm                        |   6 +-
>>>>>>  drivers/cpufreq/Makefile                           |   2 +-
>>>>>>  drivers/cpufreq/cpufreq-dt-platdev.c               |   5 +
>>>>>>  drivers/cpufreq/qcom-cpufreq-kryo.c                | 232
>>>> ------------
>>>>>>  drivers/cpufreq/qcom-cpufreq-nvmem.c               | 387
>>>> ++++++++++++++++++++
>>>>>>  include/dt-bindings/clock/qcom,gcc-msm8960.h       |   2 +
>>>>>>  26 files changed, 1941 insertions(+), 239 deletions(-)
>>>>>>  create mode 100644
>>>> Documentation/devicetree/bindings/arm/msm/qcom,kpss-gcc.txt
>>>>>>  create mode 100644
>>>> Documentation/devicetree/bindings/clock/qcom,hfpll.txt
>>>>>>  create mode 100644
>>>> Documentation/devicetree/bindings/clock/qcom,krait-cc.txt
>>>>>>  rename Documentation/devicetree/bindings/opp/{kryo-cpufreq.txt
>=>
>>>> qcom-nvmem-cpufreq.txt} (98%)
>>>>>>  create mode 100644 arch/arm/common/krait-l2-accessors.c
>>>>>>  create mode 100644 arch/arm/include/asm/krait-l2-accessors.h
>>>>>>  create mode 100644 drivers/clk/qcom/clk-hfpll.c
>>>>>>  create mode 100644 drivers/clk/qcom/clk-hfpll.h
>>>>>>  create mode 100644 drivers/clk/qcom/clk-krait.c
>>>>>>  create mode 100644 drivers/clk/qcom/clk-krait.h
>>>>>>  create mode 100644 drivers/clk/qcom/hfpll.c
>>>>>>  create mode 100644 drivers/clk/qcom/kpss-xcc.c
>>>>>>  create mode 100644 drivers/clk/qcom/krait-cc.c
>>>>>>  delete mode 100644 drivers/cpufreq/qcom-cpufreq-kryo.c
>>>>>>  create mode 100644 drivers/cpufreq/qcom-cpufreq-nvmem.c
>>>>>>
>>>>>
>> 

-- 
Please, Don't Panic



More information about the linux-arm-kernel mailing list