[PATCH V12 00/14] Krait clocks + Krait CPUfreq

Sricharan R sricharan at codeaurora.org
Fri Sep 7 02:57:34 PDT 2018


Hi Craig,


>> [v12]
>>   * Added my signed-off that was missing in some patches.
>>   * Added Bjorn's acked that i missed earlier.
>>
> 
>   Can you give this a try on your 8974 device and check if the
>   pvs version reporting, scaling for higher frequencies are fine ?
>   Sorry, i could not get hold of a 8974 device. So in-case if you still
>   have the issues with higher frequencies, can you give a quick debug
>   and report. That would be of great help.
> 
   Ping on this ..

Regards,
 Sricharan

> Regards,
>  Sricharan
> 
> 
>> [v11]
>>   * Dropped patch 13 and 14 from v10 and
>>     merged the qcom-cpufreq-krait driver to the existing qcom-cpufreq-kryo.c
>>   * Rebased on top of clk-next
>>   * Fixed a bug while populating the pvs version for krait.
>>
>> [v10]
>>   * Addressed Stephen's comments to add clocks bindings properties
>>     to the newly introduced nodes.
>>   * Added a change to include opp-supported-hw to qcom-cpufreq.c
>>   * Rebased on top of clk-next
>>   * Although there were minor changes to bindings and the driver
>>     retained the acked-by tags from Rob and Viresh respectively.    
>>
>> [v9]
>>   * Fixed a rebase issue in Makefile and added Tag from Robh.
>>
>> [v8]
>>   * Fixed a bug in path#14 pointed out by Viresh and also added tags.
>>     No change in any other patch.
>>
>> [v7]
>>   * Fixed comments from Viresh for cleaning up the error handling
>>     in qcom-cpufreq.c. Also changed the init function to lateinit
>>     call. This is required because nvmem which gets initialised with
>>     module_init needs to go first.
>>   * Fixed Rob's comments for bindings documentation
>>   * Fixed kbuild build issue in clk-lpc32xx.c
>>   * Rebased on top of clk-next
>>
>> [v6]
>>   * Adrressed comments from Viresh for patch #14 in v5 [5]
>>   * Introduced a new binding operating-points-v2-krait-cpu
>>     as per discussion with Rob
>>   * Added Review tags
>>
>> [v5]
>>   * Addressed comments from Rob for bindings
>>   * Addressed comments from Viresh to use dev_pm_opp_set_prop_name, accordingly
>>     dropped patch #12 and corrected patch #11 from previous patch set in [4]
>>   * Converted to use #spdx tags for newly introduced files
>>
>> Mostly a resend of the v3 posted by Stephen quite some time back [1]
>> except for few changes.
>>   Based on reading some feedback from list,
>>   * Dropped the patch "clk: Add safe switch hook" from v3 [2].
>>     Now this is taken care by patch#10 in this series only for Krait.
>>   * Dropped the path "clk: Avoid sending high rates to downstream
>> 		      clocks during set_rate" from v3 [3].
>>   * Rebased on top of clk-next.
>>   * Dropped the DT update from the series. Will send separately
>>   * Now with cpufreq-dt+opp supporting voltage scaling, registering the
>>     krait cpu supplies in DT should be sufficient. But one issue is,
>>     the qcom-cpufreq drivers reads the efuse and based on that registers
>>     the opp data and then registers the cpufreq-dt device. So when
>>     cpufreq-dt driver probes and registers the regulator to the OPP framework,
>>     it expects that the opp data for the device should not be registered before
>>     the regulator. Will send a RFC patch removing that check, to find out the
>>     right way of doing it.
>>
>> These patches provide cpufreq scaling on devices with Krait CPUs.
>> In Krait CPU designs there's one PLL and two muxes per CPU, allowing
>> us to switch CPU frequencies independently.
>>
>> 				 secondary
>> 	 +-----+                    +
>> 	 | QSB |-------+------------|\
>> 	 +-----+       |            | |-+
>> 		       |    +-------|/  |
>> 		       |    |       +   |
>> 	 +-----+       |    |           |
>> 	 | PLL |----+-------+           |   primary
>> 	 +-----+    |  |                |     +
>> 		    |  |                +-----|\       +------+
>> 	 +-------+  |  |                      | \      |      |
>> 	 | HFPLL |----------+-----------------|  |-----| CPU0 |
>> 	 +-------+  |  |    |                 |  |     |      |
>> 		    |  |    | +-----+         | /      +------+
>> 		    |  |    +-| / 2 |---------|/
>> 		    |  |      +-----+         +
>> 		    |  |         secondary
>> 		    |  |            +
>> 		    |  +------------|\
>> 		    |               | |-+
>> 		    +---------------|/  |   primary
>> 				    +   |     +
>> 					+-----|\       +------+
>> 	 +-------+                            | \      |      |
>> 	 | HFPLL |----------------------------|  |-----| CPU1 |
>> 	 +-------+          |                 |  |     |      |
>> 			    | +-----+         | /      +------+
>> 			    +-| / 2 |---------|/
>> 			      +-----+         +
>>
>> To support this in the common clock framework we model the muxes,
>> dividers, and PLLs as different clocks. CPUfreq only interacts
>> with the primary mux (farthest right in the diagram). When CPUfreq
>> sets a rate, the mux code finds the best parent that can provide the rate.
>> Due to the design, QSB and the top PLL are always a fixed rate and thus
>> only support one frequency each. These sources provide the lowest
>> frequencies for the CPUs. The HFPLLs are where we can make the CPU go
>> faster (GHz range). Sometimes we need to run the HFPLL twice as
>> fast and divide it by two to get a particular frequency.
>>
>> When switching rates we can't leave the CPU clocked by the HFPLL because
>> we need to turn off the output of the PLL when changing its frequency.
>> This means we have to switch over to the secondary mux and use one of the
>> fixed sources. This is why we need something like the safe parent patch.
>>
>> [1] http://lists.infradead.org/pipermail/linux-arm-kernel/2015-March/332607.html
>> [2] http://lists.infradead.org/pipermail/linux-arm-kernel/2015-March/332615.html
>> [3] http://lists.infradead.org/pipermail/linux-arm-kernel/2015-March/332608.html
>> [4] https://lwn.net/Articles/740994/ 
>> [5] https://lkml.org/lkml/2017/12/19/537
>>
>>
>> Sricharan R (3):
>>   clk: qcom: Add safe switch hook for krait mux clocks
>>   cpufreq: qcom: Re-organise kryo cpufreq to use it for other nvmem
>>     based qcom socs
>>   cpufreq: qcom: Add support for krait based socs
>>
>> Stephen Boyd (11):
>>   ARM: Add Krait L2 register accessor functions
>>   clk: qcom: Add support for High-Frequency PLLs (HFPLLs)
>>   clk: qcom: Add HFPLL driver
>>   dt-bindings: clock: Document qcom,hfpll
>>   clk: qcom: Add MSM8960/APQ8064's HFPLLs
>>   clk: qcom: Add IPQ806X's HFPLLs
>>   clk: qcom: Add support for Krait clocks
>>   clk: qcom: Add KPSS ACC/GCC driver
>>   dt-bindings: arm: Document qcom,kpss-gcc
>>   clk: qcom: Add Krait clock controller driver
>>   dt-bindings: clock: Document qcom,krait-cc
>>
>>  .../devicetree/bindings/arm/msm/qcom,kpss-acc.txt  |  19 +
>>  .../devicetree/bindings/arm/msm/qcom,kpss-gcc.txt  |  44 +++
>>  .../devicetree/bindings/clock/qcom,hfpll.txt       |  60 ++++
>>  .../devicetree/bindings/clock/qcom,krait-cc.txt    |  34 ++
>>  .../{kryo-cpufreq.txt => qcom-nvmem-cpufreq.txt}   |   7 +-
>>  arch/arm/common/Kconfig                            |   3 +
>>  arch/arm/common/Makefile                           |   1 +
>>  arch/arm/common/krait-l2-accessors.c               |  48 +++
>>  arch/arm/include/asm/krait-l2-accessors.h          |   9 +
>>  drivers/clk/qcom/Kconfig                           |  28 ++
>>  drivers/clk/qcom/Makefile                          |   5 +
>>  drivers/clk/qcom/clk-hfpll.c                       | 244 +++++++++++++
>>  drivers/clk/qcom/clk-hfpll.h                       |  44 +++
>>  drivers/clk/qcom/clk-krait.c                       | 126 +++++++
>>  drivers/clk/qcom/clk-krait.h                       |  40 +++
>>  drivers/clk/qcom/gcc-ipq806x.c                     |  82 +++++
>>  drivers/clk/qcom/gcc-msm8960.c                     | 172 +++++++++
>>  drivers/clk/qcom/hfpll.c                           |  96 +++++
>>  drivers/clk/qcom/kpss-xcc.c                        |  87 +++++
>>  drivers/clk/qcom/krait-cc.c                        | 397 +++++++++++++++++++++
>>  drivers/cpufreq/Kconfig.arm                        |   6 +-
>>  drivers/cpufreq/Makefile                           |   2 +-
>>  drivers/cpufreq/cpufreq-dt-platdev.c               |   5 +
>>  drivers/cpufreq/qcom-cpufreq-kryo.c                | 232 ------------
>>  drivers/cpufreq/qcom-cpufreq-nvmem.c               | 387 ++++++++++++++++++++
>>  include/dt-bindings/clock/qcom,gcc-msm8960.h       |   2 +
>>  26 files changed, 1941 insertions(+), 239 deletions(-)
>>  create mode 100644 Documentation/devicetree/bindings/arm/msm/qcom,kpss-gcc.txt
>>  create mode 100644 Documentation/devicetree/bindings/clock/qcom,hfpll.txt
>>  create mode 100644 Documentation/devicetree/bindings/clock/qcom,krait-cc.txt
>>  rename Documentation/devicetree/bindings/opp/{kryo-cpufreq.txt => qcom-nvmem-cpufreq.txt} (98%)
>>  create mode 100644 arch/arm/common/krait-l2-accessors.c
>>  create mode 100644 arch/arm/include/asm/krait-l2-accessors.h
>>  create mode 100644 drivers/clk/qcom/clk-hfpll.c
>>  create mode 100644 drivers/clk/qcom/clk-hfpll.h
>>  create mode 100644 drivers/clk/qcom/clk-krait.c
>>  create mode 100644 drivers/clk/qcom/clk-krait.h
>>  create mode 100644 drivers/clk/qcom/hfpll.c
>>  create mode 100644 drivers/clk/qcom/kpss-xcc.c
>>  create mode 100644 drivers/clk/qcom/krait-cc.c
>>  delete mode 100644 drivers/cpufreq/qcom-cpufreq-kryo.c
>>  create mode 100644 drivers/cpufreq/qcom-cpufreq-nvmem.c
>>
> 

-- 
"QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum, hosted by The Linux Foundation



More information about the linux-arm-kernel mailing list