[PATCH v2 2/2] phy: zynqmp: Add dt bindings for ZynqMP phy

Vivek Gautam vivek.gautam at codeaurora.org
Wed Sep 5 01:59:09 PDT 2018



On 9/3/2018 5:44 PM, Anurag Kumar Vulisha wrote:
> This patch adds the document describing dt bindings for ZynqMP
> phy. ZynqMP SOC has a High Speed Processing System Gigabit
> Transceiver which provides PHY capabilties to USB, SATA,
> PCIE, Display Port and Ehernet SGMII controllers.
>
> Signed-off-by: Anurag Kumar Vulisha <anurag.kumar.vulisha at xilinx.com>
> ---
>   changes in v2:
> 	1. None
> ---
>   .../devicetree/bindings/phy/phy-zynqmp.txt         | 104 +++++++++++++++++++++
>   1 file changed, 104 insertions(+)
>   create mode 100644 Documentation/devicetree/bindings/phy/phy-zynqmp.txt
>
> diff --git a/Documentation/devicetree/bindings/phy/phy-zynqmp.txt b/Documentation/devicetree/bindings/phy/phy-zynqmp.txt
> new file mode 100644
> index 0000000..2eed553
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/phy/phy-zynqmp.txt
> @@ -0,0 +1,104 @@
> +Xilinx ZynqMP PHY binding
> +
> +This binding describes a ZynqMP PHY device that is used to control ZynqMP
> +High Speed Gigabit Transceiver(GT). ZynqMP PS GTR provides four lanes
> +and are used by USB, SATA, PCIE, Display port and Ethernet SGMMI controllers.
> +
> +Phy provider node
> +=================
> +
> +Required properties:
> +- compatible	: Can be "xlnx,zynqmp-psgtr-v1.1" or "xlnx,zynqmp-psgtr"
> +		  "xlnx,zynqmp-psgtr-v1.1" has "xlnx,tx_termination_fix" removed
This is not very clear. You can rather mention this statement for the 
property.
e.g. In "xlnx,tx_termination_fix" you can write - this is not required 
for "xlnx,zynqmp-psgtr-v1.1.

> +
> +- reg           : Address and length of register sets for each device in
> +                  "reg-names"
> +
> +- reg-names     : The names of the register addresses corresponding to the
> +		  registers filled in "reg":
> +			- serdes: SERDES block register set
> +			- siou: SIOU block register set
> +
> +Optional properties:
> +- xlnx,tx_termination_fix : Include this for fixing functional issue with the
> +		  TX termination resistance in GT, which can be out of spec for
> +		  the XCZU9EG silicon version.
> +
> +Required nodes	:  A sub-node is required for each lane the controller
> +		   provides.
> +
> +Phy sub-nodes
> +=============
> +
> +Required properties:
> +lane0:
> +- #phy-cells	: Should be 4
> +
> +lane1:
> +- #phy-cells	: Should be 4
> +
> +lane2:
> +- #phy-cells	: Should be 4
> +
> +lane3:
> +- #phy-cells	: Should be 4
> +
> +Example:
> +	serdes: zynqmp_phy at fd400000 {

phy is not just the serdes. Also s/zynqmp_phy/phy

This could be:
                     zynqmp_phy: phy at fd400000

regards
Vivek
> +		compatible = "xlnx,zynqmp-psgtr-v1.1";
> +		status = "okay";
> +		reg = <0x0 0xfd400000 0x0 0x40000>, <0x0 0xfd3d0000 0x0 0x1000>;
> +		reg-names = "serdes", "siou";
> +
> +		lane0: lane at 0 {
> +			#phy-cells = <4>;
> +		};
> +		lane1: lane at 1 {
> +			#phy-cells = <4>;
> +		};
> +		lane2: lane at 2 {
> +			#phy-cells = <4>;
> +		};
> +		lane3: lane at 3 {
> +			#phy-cells = <4>;
> +		};
> +	};
> +
> +Specifying phy control of devices
> +=================================
> +
> +Device nodes should specify the configuration required in their "phys"
> +property, containing a phandle to the phy port node and a device type.
> +
> +phys = <PHANDLE CONTROLLER_TYPE CONTROLLER_INSTANCE LANE_NUM LANE_FREQ>;
> +
> +PHANDLE                 = &lane0 or &lane1 or &lane2 or &lane3
> +CONTROLLER_TYPE         = PHY_TYPE_PCIE or PHY_TYPE_SATA or PHY_TYPE_USB
> +			  or PHY_TYPE_DP or PHY_TYPE_SGMII
> +CONTROLLER_INSTANCE     = Depends on controller type used, can be any of
> +				PHY_TYPE_PCIE : 0 or 1 or 2 or 3
> +				PHY_TYPE_SATA : 0 or 1
> +				PHY_TYPE_USB  : 0 or 1
> +				PHY_TYPE_DP   : 0 or 1
> +				PHY_TYPE_SGMII: 0 or 1 or 2 or 3
> +LANE_NUM                = Depends on which lane clock is used as ref clk, can be
> +			  0 or 1 or 2 or 3
> +LANE_FREQ               = Frequency that controller can operate, can be any of
> +			  19.2Mhz,20Mhz,24Mhz,26Mhz,27Mhz,28.4Mhz,40Mhz,52Mhz,
> +			  100Mhz,108Mhz,125Mhz,135Mhz,150Mhz
> +
> +Example:
> +
> +#include <dt-bindings/phy/phy.h>
> +
> +	usb at fe200000 {
> +		...
> +		phys	  = <&lane2 PHY_TYPE_USB3 0 2 2600000>;
> +		...
> +	};
> +
> +	ahci at fd0c0000 {
> +		...
> +		phys	  = <&lane3 PHY_TYPE_SATA 1 1 125000000>;
> +		...
> +	};




More information about the linux-arm-kernel mailing list