[PATCH net-next v3 00/10] net: mvpp2: phylink conversion

Gregory CLEMENT gregory.clement at bootlin.com
Thu May 17 05:23:00 PDT 2018


Hi Antoine,
 
 On jeu., mai 17 2018, Antoine Tenart <antoine.tenart at bootlin.com> wrote:

> Hi Dave, Russell,
>
> This series convert the Marvell PPv2 driver to phylink (models the MAC
> to PHY link).
>
> One important point is the PPv2 driver supports two probe modes: device
> tree and ACPI. This series only brings phylink support for the device
> tree mode, as the ACPI one will need further work. Still, the driver
> should be working as before when using ACPI. This split should be
> temporary, and was discussed with Marcin (in Cc.) who added ACPI support
> to the driver.
>
> Also as the SFP cages on both DB boards can be considered as non-wired.
> We thus chose not to describe those SFP cages and we use fixed-link.
>
> The rest of the series uses phylink to add support for 1000BaseX and
> 2500BaseX modes in the PPv2 driver. To do this, two patches are needed
> in the common PHY framework (patches 3 and 4). The last 4 patches modify
> the device tree to use the new PPv2 functionalities.
>
> The series has been tested for the device tree mode on the 7040-db,
> 8040-db and 8040-mcbin boards, to ensure all the interface where working
> as expected.
>
> @Dave: patches 7 to 10 should go through the mvebu tree (Gregory in
> Cc.) to avoid any conflict with the other mvebu dt patches taken during
> this cycle.

Patches 7 to 10 have been applied on mvebu/dt64.

Thanks,

Gregory

>
> The series is based on today's net-next.
>
> Thanks!
> Antoine
>
> Since v2:
>   - Removed the SFP description from the DB boards, as their SFP cages
>     are wired properly. We now use fixed-link.
>   - Because of this rework, split the series in two, so that the SFP
>     part is reviewed separately.
>   - Small fixes in the phylink patch.
>   - Rebased on the latest net-next branch.
>
> Since v1:
>   - Chose a different approach to the SFP changes, as the previous ones
>     weren't valid and reworked both BD boards device trees.
>   - Misc fixes.
>   - Added Kishon's acked-by on one patch.
>   - Rebaed on latest net-next branch.
>
> Antoine Tenart (9):
>   net: mvpp2: align the ethtool ops definition
>   net: mvpp2: phylink support
>   phy: add 2.5G SGMII mode to the phy_mode enum
>   phy: cp110-comphy: 2.5G SGMII mode
>   net: mvpp2: 1000baseX support
>   net: mvpp2: 2500baseX support
>   arm64: dts: marvell: mcbin: enable the fourth network interface
>   arm64: dts: marvell: 8040-db: describe the 10G interfaces as
>     fixed-link
>   arm64: dts: marvell: 7040-db: describe the 10G interface as fixed-link
>
> Russell King (1):
>   arm64: dts: marvell: mcbin: add 10G SFP support
>
>  .../arm64/boot/dts/marvell/armada-7040-db.dts |   5 +
>  .../arm64/boot/dts/marvell/armada-8040-db.dts |  10 +
>  .../boot/dts/marvell/armada-8040-mcbin.dts    |  70 ++
>  drivers/net/ethernet/marvell/Kconfig          |   1 +
>  drivers/net/ethernet/marvell/mvpp2.c          | 931 +++++++++++-------
>  drivers/phy/marvell/phy-mvebu-cp110-comphy.c  |  17 +-
>  include/linux/phy/phy.h                       |   1 +
>  7 files changed, 680 insertions(+), 355 deletions(-)
>
> -- 
> 2.17.0
>

-- 
Gregory Clement, Bootlin (formerly Free Electrons)
Embedded Linux and Kernel engineering
http://bootlin.com



More information about the linux-arm-kernel mailing list