[PATCH v5 2/2] ThunderX2: Add Cavium ThunderX2 SoC UNCORE PMU driver
John Garry
john.garry at huawei.com
Thu May 17 04:12:05 PDT 2018
On 16/05/2018 05:55, Ganapatrao Kulkarni wrote:
> This patch adds a perf driver for the PMU UNCORE devices DDR4 Memory
> Controller(DMC) and Level 3 Cache(L3C).
>
Hi,
Just some coding comments below:
> ThunderX2 has 8 independent DMC PMUs to capture performance events
> corresponding to 8 channels of DDR4 Memory Controller and 16 independent
> L3C PMUs to capture events corresponding to 16 tiles of L3 cache.
> Each PMU supports up to 4 counters. All counters lack overflow interrupt
> and are sampled periodically.
>
> Signed-off-by: Ganapatrao Kulkarni <ganapatrao.kulkarni at cavium.com>
> ---
> drivers/perf/Kconfig | 8 +
> drivers/perf/Makefile | 1 +
> drivers/perf/thunderx2_pmu.c | 965 +++++++++++++++++++++++++++++++++++++++++++
> include/linux/cpuhotplug.h | 1 +
> 4 files changed, 975 insertions(+)
> create mode 100644 drivers/perf/thunderx2_pmu.c
>
> diff --git a/drivers/perf/Kconfig b/drivers/perf/Kconfig
> index 28bb5a0..eafd0fc 100644
> --- a/drivers/perf/Kconfig
> +++ b/drivers/perf/Kconfig
> @@ -85,6 +85,14 @@ config QCOM_L3_PMU
> Adds the L3 cache PMU into the perf events subsystem for
> monitoring L3 cache events.
>
> +config THUNDERX2_PMU
> + bool "Cavium ThunderX2 SoC PMU UNCORE"
> + depends on ARCH_THUNDER2 && PERF_EVENTS && ACPI
Is the explicit dependency for PERF_EVENTS required, since we're under
the PERF_EVENTS menu?
And IIRC for other perf drivers we required a dependency on ARM64 - is
that required here also? I see arm_smccc_smc() calls in the code...
> + help
> + Provides support for ThunderX2 UNCORE events.
> + The SoC has PMU support in its L3 cache controller (L3C) and
> + in the DDR4 Memory Controller (DMC).
> +
> config XGENE_PMU
> depends on ARCH_XGENE
> bool "APM X-Gene SoC PMU"
> diff --git a/drivers/perf/Makefile b/drivers/perf/Makefile
> index b3902bd..909f27f 100644
> --- a/drivers/perf/Makefile
> +++ b/drivers/perf/Makefile
> @@ -7,5 +7,6 @@ obj-$(CONFIG_ARM_PMU_ACPI) += arm_pmu_acpi.o
> obj-$(CONFIG_HISI_PMU) += hisilicon/
> obj-$(CONFIG_QCOM_L2_PMU) += qcom_l2_pmu.o
> obj-$(CONFIG_QCOM_L3_PMU) += qcom_l3_pmu.o
> +obj-$(CONFIG_THUNDERX2_PMU) += thunderx2_pmu.o
> obj-$(CONFIG_XGENE_PMU) += xgene_pmu.o
> obj-$(CONFIG_ARM_SPE_PMU) += arm_spe_pmu.o
> diff --git a/drivers/perf/thunderx2_pmu.c b/drivers/perf/thunderx2_pmu.c
> new file mode 100644
> index 0000000..0401443
> --- /dev/null
> +++ b/drivers/perf/thunderx2_pmu.c
> @@ -0,0 +1,965 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * CAVIUM THUNDERX2 SoC PMU UNCORE
> + *
> + * Copyright (C) 2018 Cavium Inc.
> + * Author: Ganapatrao Kulkarni <gkulkarni at cavium.com>
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License version 2 as
> + * published by the Free Software Foundation.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + *
> + * You should have received a copy of the GNU General Public License
> + * along with this program. If not, see <http://www.gnu.org/licenses/>.
> + */
Isn't this the same as the SPDX?
> +
> +#include <linux/acpi.h>
> +#include <linux/arm-smccc.h>
> +#include <linux/cpuhotplug.h>
> +#include <linux/perf_event.h>
> +#include <linux/platform_device.h>
> +
> +/* L3c and DMC has 16 and 8 channels per socket respectively.
L3C, right?
> + * Each Channel supports UNCORE PMU device and consists of
> + * 4 independent programmable counters. Counters are 32 bit
> + * and does not support overflow interrupt, they needs to be
/s/needs/need/, /s/does/do/
> + * sampled before overflow(i.e, at every 2 seconds).
how can you ensure that this value is low enough?
"I saw this comment in previous patch:
> Given that all channels compete for access to the muxed register
> interface, I suspect we need to try more often than once every 2
> seconds...
2 seconds seems to be sufficient. So far testing looks good."
Can you provide any more analytical reasoning than this?
> + */
> +
> +#define UNCORE_MAX_COUNTERS 4
> +#define UNCORE_L3_MAX_TILES 16
> +#define UNCORE_DMC_MAX_CHANNELS 8
> +
> +#define UNCORE_HRTIMER_INTERVAL (2 * NSEC_PER_SEC)
> +#define GET_EVENTID(ev) ((ev->hw.config) & 0x1ff)
> +#define GET_COUNTERID(ev) ((ev->hw.idx) & 0xf)
> +#define GET_CHANNELID(pmu_uncore) (pmu_uncore->channel)
> +#define DMC_EVENT_CFG(idx, val) ((val) << (((idx) * 8) + 1))
> +
> +#define DMC_COUNTER_CTL 0x234
> +#define DMC_COUNTER_DATA 0x240
> +#define L3C_COUNTER_CTL 0xA8
> +#define L3C_COUNTER_DATA 0xAC
I feel it's generally better to keep register offsets in numeric order
(if indeed, that is what they are)
> +
> +#define THUNDERX2_SMC_CALL_ID 0xC200FF00
> +#define THUNDERX2_SMC_SET_CHANNEL 0xB010
> +
> +enum thunderx2_uncore_l3_events {
> + L3_EVENT_NONE,
> + L3_EVENT_NBU_CANCEL,
> + L3_EVENT_DIB_RETRY,
> + L3_EVENT_DOB_RETRY,
> + L3_EVENT_DIB_CREDIT_RETRY,
> + L3_EVENT_DOB_CREDIT_RETRY,
> + L3_EVENT_FORCE_RETRY,
> + L3_EVENT_IDX_CONFLICT_RETRY,
> + L3_EVENT_EVICT_CONFLICT_RETRY,
> + L3_EVENT_BANK_CONFLICT_RETRY,
> + L3_EVENT_FILL_ENTRY_RETRY,
> + L3_EVENT_EVICT_NOT_READY_RETRY,
> + L3_EVENT_L3_RETRY,
> + L3_EVENT_READ_REQ,
> + L3_EVENT_WRITE_BACK_REQ,
> + L3_EVENT_INVALIDATE_NWRITE_REQ,
> + L3_EVENT_INV_REQ,
> + L3_EVENT_SELF_REQ,
> + L3_EVENT_REQ,
> + L3_EVENT_EVICT_REQ,
> + L3_EVENT_INVALIDATE_NWRITE_HIT,
> + L3_EVENT_INVALIDATE_HIT,
> + L3_EVENT_SELF_HIT,
> + L3_EVENT_READ_HIT,
> + L3_EVENT_MAX,
',' required?
> +};
> +
> +enum thunderx2_uncore_dmc_events {
> + DMC_EVENT_NONE,
> + DMC_EVENT_COUNT_CYCLES,
> + DMC_EVENT_RES2,
> + DMC_EVENT_RES3,
> + DMC_EVENT_RES4,
> + DMC_EVENT_RES5,
> + DMC_EVENT_RES6,
> + DMC_EVENT_RES7,
> + DMC_EVENT_RES8,
> + DMC_EVENT_READ_64B_TXNS,
> + DMC_EVENT_READ_BELOW_64B_TXNS,
> + DMC_EVENT_WRITE_TXNS,
> + DMC_EVENT_TXN_CYCLES,
> + DMC_EVENT_DATA_TRANSFERS,
> + DMC_EVENT_CANCELLED_READ_TXNS,
> + DMC_EVENT_CONSUMED_READ_TXNS,
> + DMC_EVENT_MAX,
ditto
> +};
> +
> +enum thunderx2_uncore_type {
> + PMU_TYPE_L3C,
> + PMU_TYPE_DMC,
> + PMU_TYPE_INVALID,
> +};
> +
> +/*
> + * pmu on each socket has 2 uncore devices(dmc and l3),
> + * each uncore device has up to 16 channels, each channel can sample
> + * events independently with counters up to 4.
> + *
> + * struct thunderx2_pmu_uncore_channel created per channel.
> + * struct thunderx2_pmu_uncore_dev per uncore device.
this comment is a bit obvious
> + */
> +struct thunderx2_pmu_uncore_channel {
> + struct pmu pmu;
> + struct hlist_node node;
> + struct thunderx2_pmu_uncore_dev *uncore_dev;
> + int channel;
> + int cpu;
> + DECLARE_BITMAP(active_counters, UNCORE_MAX_COUNTERS);
> + struct perf_event *events[UNCORE_MAX_COUNTERS];
> + struct hrtimer hrtimer;
> + /* to sync counter alloc/release */
> + raw_spinlock_t lock;
> +};
> +
> +struct thunderx2_pmu_uncore_dev {
> + char *name;
> + struct device *dev;
> + enum thunderx2_uncore_type type;
> + void __iomem *base;
> + int node;
> + u32 max_counters;
> + u32 max_channels;
> + u32 max_events;
> + u64 hrtimer_interval;
> + /* this lock synchronizes across channels */
> + raw_spinlock_t lock;
> + const struct attribute_group **attr_groups;
> + void (*init_cntr_base)(struct perf_event *event,
> + struct thunderx2_pmu_uncore_dev *uncore_dev);
> + void (*select_channel)(struct perf_event *event);
> + void (*stop_event)(struct perf_event *event);
> + void (*start_event)(struct perf_event *event, int flags);
> +};
> +
> +static inline struct thunderx2_pmu_uncore_channel *
is inline keyword required or even used generally? Since static, can't
the compiler figure this out?
> +pmu_to_thunderx2_pmu_uncore(struct pmu *pmu)
> +{
> + return container_of(pmu, struct thunderx2_pmu_uncore_channel, pmu);
> +}
> +
> +/*
> + * sysfs format attributes
> + */
can't this comment fit on a single line?
> +static ssize_t thunderx2_pmu_format_show(struct device *dev,
> + struct device_attribute *attr, char *buf)
> +{
> + struct dev_ext_attribute *eattr;
> +
> + eattr = container_of(attr, struct dev_ext_attribute, attr);
> + return sprintf(buf, "%s\n", (char *) eattr->var);
> +}
> +
> +#define FORMAT_ATTR(_name, _config) \
> + (&((struct dev_ext_attribute[]) { \
> + { \
> + .attr = __ATTR(_name, 0444, thunderx2_pmu_format_show, NULL), \
> + .var = (void *) _config, \
> + } \
> + })[0].attr.attr)
> +
> +static struct attribute *l3c_pmu_format_attrs[] = {
> + FORMAT_ATTR(event, "config:0-4"),
> + NULL,
> +};
> +
> +static struct attribute *dmc_pmu_format_attrs[] = {
> + FORMAT_ATTR(event, "config:0-4"),
> + NULL,
> +};
> +
> +static const struct attribute_group l3c_pmu_format_attr_group = {
> + .name = "format",
> + .attrs = l3c_pmu_format_attrs,
> +};
> +
> +static const struct attribute_group dmc_pmu_format_attr_group = {
> + .name = "format",
> + .attrs = dmc_pmu_format_attrs,
> +};
> +
[ ... ]
> + * Per PMU device attribute groups
> + */
> +static const struct attribute_group *l3c_pmu_attr_groups[] = {
> + &l3c_pmu_format_attr_group,
> + &pmu_cpumask_attr_group,
> + &l3c_pmu_events_attr_group,
> + NULL
> +};
> +
> +static const struct attribute_group *dmc_pmu_attr_groups[] = {
> + &dmc_pmu_format_attr_group,
> + &pmu_cpumask_attr_group,
> + &dmc_pmu_events_attr_group,
> + NULL
> +};
> +
> +static inline u32 reg_readl(unsigned long addr)
> +{
> + return readl((void __iomem *)addr);
> +}
> +
> +static inline void reg_writel(u32 val, unsigned long addr)
> +{
> + writel(val, (void __iomem *)addr);
> +}
> +
> +static int alloc_counter(struct thunderx2_pmu_uncore_channel *pmu_uncore)
> +{
> + int counter;
> +
> + raw_spin_lock(&pmu_uncore->lock);
> + counter = find_first_zero_bit(pmu_uncore->active_counters,
> + pmu_uncore->uncore_dev->max_counters);
> + if (counter == pmu_uncore->uncore_dev->max_counters) {
> + raw_spin_unlock(&pmu_uncore->lock);
> + return -ENOSPC;
> + }
> + set_bit(counter, pmu_uncore->active_counters);
> + raw_spin_unlock(&pmu_uncore->lock);
> + return counter;
> +}
> +
> +static void free_counter(
> + struct thunderx2_pmu_uncore_channel *pmu_uncore, int counter)
strange formatting
> +{
> + raw_spin_lock(&pmu_uncore->lock);
> + clear_bit(counter, pmu_uncore->active_counters);
> + raw_spin_unlock(&pmu_uncore->lock);
> +}
> +
[ ... ]
> +static void uncore_stop_event_l3c(struct perf_event *event)
> +{
> + reg_writel(0, event->hw.config_base);
> +}
> +
> +static void uncore_start_event_dmc(struct perf_event *event, int flags)
> +{
> + u32 val;
> + struct hw_perf_event *hwc = &event->hw;
> + int idx = GET_COUNTERID(event);
> + int event_type = GET_EVENTID(event);
> +
> + /* enable and start counters.
> + * 8 bits for each counter, bits[05:01] of a counter to set event type.
> + */
> + val = reg_readl(hwc->config_base);
> + val &= ~DMC_EVENT_CFG(idx, 0x1f);
> + val |= DMC_EVENT_CFG(idx, event_type);
> + reg_writel(val, hwc->config_base);
> + local64_set(&hwc->prev_count, 0);
> + reg_writel(0, hwc->event_base);
> +}
> +
> +static void uncore_stop_event_dmc(struct perf_event *event)
> +{
> + u32 val;
> + struct hw_perf_event *hwc = &event->hw;
> + int idx = GET_COUNTERID(event);
> +
> + /* clear event type(bits[05:01]) to stop counter */
> + val = reg_readl(hwc->config_base);
> + val &= ~DMC_EVENT_CFG(idx, 0x1f);
> + reg_writel(val, hwc->config_base);
> +}
> +
> +static void init_cntr_base_l3c(struct perf_event *event,
> + struct thunderx2_pmu_uncore_dev *uncore_dev)
> +{
> + struct hw_perf_event *hwc = &event->hw;
> +
> + /* counter ctrl/data reg offset at 8 */
> + hwc->config_base = (unsigned long)uncore_dev->base
> + + L3C_COUNTER_CTL + (8 * GET_COUNTERID(event));
> + hwc->event_base = (unsigned long)uncore_dev->base
> + + L3C_COUNTER_DATA + (8 * GET_COUNTERID(event));
Is there a better way to hold this, since we're casting back to a void *
when writing to the register?
> +}
> +
> +static void init_cntr_base_dmc(struct perf_event *event,
> + struct thunderx2_pmu_uncore_dev *uncore_dev)
> +{
> + struct hw_perf_event *hwc = &event->hw;
> +
> + hwc->config_base = (unsigned long)uncore_dev->base
> + + DMC_COUNTER_CTL;
> + /* counter data reg offset at 0xc */
> + hwc->event_base = (unsigned long)uncore_dev->base
> + + DMC_COUNTER_DATA + (0xc * GET_COUNTERID(event));
> +}
> +
> +static void thunderx2_uncore_update(struct perf_event *event)
> +{
> + s64 prev, new = 0;
> + u64 delta;
> + struct hw_perf_event *hwc = &event->hw;
> + struct thunderx2_pmu_uncore_channel *pmu_uncore;
> + enum thunderx2_uncore_type type;
> +
> + pmu_uncore = pmu_to_thunderx2_pmu_uncore(event->pmu);
> + type = pmu_uncore->uncore_dev->type;
> +
> + pmu_uncore->uncore_dev->select_channel(event);
> +
> + new = reg_readl(hwc->event_base);
> + prev = local64_xchg(&hwc->prev_count, new);
> +
> + /* handles rollover of 32 bit counter */
> + delta = (u32)(((1UL << 32) - prev) + new);
> + local64_add(delta, &event->count);
> +}
> +
> +enum thunderx2_uncore_type get_uncore_device_type(struct acpi_device *adev)
> +{
> + int i = 0;
> + struct acpi_uncore_device {
> + __u8 id[ACPI_ID_LEN];
> + enum thunderx2_uncore_type type;
> + } devices[] = {
> + {"CAV901D", PMU_TYPE_L3C},
> + {"CAV901F", PMU_TYPE_DMC},
> + {"", PMU_TYPE_INVALID},
for sentinels, ',' should not be required
> + };
> +
> + while (devices[i].type != PMU_TYPE_INVALID) {
> + if (!strcmp(acpi_device_hid(adev), devices[i].id))
> + return devices[i].type;
Can't you use acpi_match_device()?
> + i++;
> + }
> + return PMU_TYPE_INVALID;
> +}
> +
> +/*
> + * We must NOT create groups containing events from multiple hardware PMUs,
> + * although mixing different software and hardware PMUs is allowed.
> + */
> +static bool thunderx2_uncore_validate_event_group(struct perf_event *event)
[ ... ]
> +
> +static int thunderx2_pmu_uncore_add(struct thunderx2_pmu_uncore_dev *uncore_dev,
> + int channel)
> +{
> + struct thunderx2_pmu_uncore_channel *pmu_uncore;
> + int ret, cpu;
> +
> + pmu_uncore = devm_kzalloc(uncore_dev->dev, sizeof(*pmu_uncore),
> + GFP_KERNEL);
> + if (!pmu_uncore)
> + return -ENOMEM;
> +
> + cpu = cpumask_any_and(cpumask_of_node(uncore_dev->node),
> + cpu_online_mask);
> + if (cpu >= nr_cpu_ids)
> + return -EINVAL;
> +
> + pmu_uncore->cpu = cpu;
> + pmu_uncore->channel = channel;
> + pmu_uncore->uncore_dev = uncore_dev;
> +
> + hrtimer_init(&pmu_uncore->hrtimer, CLOCK_MONOTONIC, HRTIMER_MODE_REL);
> + pmu_uncore->hrtimer.function = thunderx2_uncore_hrtimer_callback;
> +
> + ret = thunderx2_pmu_uncore_register(pmu_uncore);
> + if (ret) {
> + dev_err(uncore_dev->dev, "%s PMU: Failed to init driver\n",
> + uncore_dev->name);
> + return -ENODEV;
> + }
> +
> + /* register hotplug callback for the pmu */
> + ret = cpuhp_state_add_instance(
> + CPUHP_AP_PERF_ARM_THUNDERX2_UNCORE_ONLINE,
> + &pmu_uncore->node);
> + if (ret) {
> + dev_err(uncore_dev->dev, "Error %d registering hotplug", ret);
> + return ret;
> + }
> +
> + dev_dbg(uncore_dev->dev, "%s PMU UNCORE registered\n",
> + pmu_uncore->pmu.name);
strange alignment, and many more times in the code
> + return ret;
> +}
> +
> +static struct thunderx2_pmu_uncore_dev *init_pmu_uncore_dev(
> + struct device *dev, acpi_handle handle,
> + struct acpi_device *adev, u32 type)
> +{
> + struct thunderx2_pmu_uncore_dev *uncore_dev;
> + void __iomem *base;
> + struct resource res;
> + struct resource_entry *rentry;
> + struct list_head list;
> + int ret;
> +
> + INIT_LIST_HEAD(&list);
> + ret = acpi_dev_get_resources(adev, &list, NULL, NULL);
> + if (ret <= 0) {
> + dev_err(dev, "failed to parse _CRS method, error %d\n", ret);
> + return NULL;
> + }
> +
> + list_for_each_entry(rentry, &list, node) {
> + if (resource_type(rentry->res) == IORESOURCE_MEM) {
> + res = *rentry->res;
> + break;
> + }
> + }
what I am missing that you can not use
platform_get_resource(,IORESOURCE_MEM,)?
And I also wonder if you need all the device-related arguments for the code
> +
> + if (!rentry->res)
> + return NULL;
> +
> + acpi_dev_free_resource_list(&list);
> + base = devm_ioremap_resource(dev, &res);
> + if (IS_ERR(base)) {
> + dev_err(dev, "PMU type %d: Fail to map resource\n", type);
> + return NULL;
> + }
> +
> + uncore_dev = devm_kzalloc(dev, sizeof(*uncore_dev), GFP_KERNEL);
> + if (!uncore_dev)
> + return NULL;
> +
> + uncore_dev->dev = dev;
> + uncore_dev->type = type;
> + uncore_dev->base = base;
> + uncore_dev->node = dev_to_node(dev);
> +
> + raw_spin_lock_init(&uncore_dev->lock);
> +
> + switch (uncore_dev->type) {
if we can re-arrange, isn't it better to do the steps which can fail
before the steps which can't?
> + case PMU_TYPE_L3C:
> + uncore_dev->max_counters = UNCORE_MAX_COUNTERS;
> + uncore_dev->max_channels = UNCORE_L3_MAX_TILES;
> + uncore_dev->max_events = L3_EVENT_MAX;
> + uncore_dev->hrtimer_interval = UNCORE_HRTIMER_INTERVAL;
> + uncore_dev->attr_groups = l3c_pmu_attr_groups;
> + uncore_dev->name = devm_kasprintf(dev, GFP_KERNEL,
> + "uncore_l3c_%d", uncore_dev->node);
> + uncore_dev->init_cntr_base = init_cntr_base_l3c;
> + uncore_dev->start_event = uncore_start_event_l3c;
> + uncore_dev->stop_event = uncore_stop_event_l3c;
> + uncore_dev->select_channel = uncore_select_channel;
it's possible to bring the common code outside the swicth statement, but
probably not worth it
> + break;
> + case PMU_TYPE_DMC:
> + uncore_dev->max_counters = UNCORE_MAX_COUNTERS;
> + uncore_dev->max_channels = UNCORE_DMC_MAX_CHANNELS;
> + uncore_dev->max_events = DMC_EVENT_MAX;
> + uncore_dev->hrtimer_interval = UNCORE_HRTIMER_INTERVAL;
> + uncore_dev->attr_groups = dmc_pmu_attr_groups;
> + uncore_dev->name = devm_kasprintf(dev, GFP_KERNEL,
> + "uncore_dmc_%d", uncore_dev->node);
> + uncore_dev->init_cntr_base = init_cntr_base_dmc;
> + uncore_dev->start_event = uncore_start_event_dmc;
> + uncore_dev->stop_event = uncore_stop_event_dmc;
> + uncore_dev->select_channel = uncore_select_channel;
> + break;
> + case PMU_TYPE_INVALID:
> + devm_kfree(dev, uncore_dev);
do you really need this?
> + uncore_dev = NULL;
> + break;
return NULL
And don't we require a default statement?
> + }
> +
> + return uncore_dev;
> +}
> +
> +static acpi_status thunderx2_pmu_uncore_dev_add(acpi_handle handle, u32 level,
> + void *data, void **return_value)
> +{
> + struct thunderx2_pmu_uncore_dev *uncore_dev;
> + struct acpi_device *adev;
> + enum thunderx2_uncore_type type;
> + int channel;
> +
> + if (acpi_bus_get_device(handle, &adev))
> + return AE_OK;
> + if (acpi_bus_get_status(adev) || !adev->status.present)
> + return AE_OK;
> +
> + type = get_uncore_device_type(adev);
> + if (type == PMU_TYPE_INVALID)
> + return AE_OK;
> +
> + uncore_dev = init_pmu_uncore_dev((struct device *)data, handle,
no need to cast void *
> + adev, type);
> +
> + if (!uncore_dev)
> + return AE_ERROR;
> +
> + for (channel = 0; channel < uncore_dev->max_channels; channel++) {
> + if (thunderx2_pmu_uncore_add(uncore_dev, channel)) {
> + /* Can't add the PMU device, abort */
> + return AE_ERROR;
> + }
> + }
> + return AE_OK;
> +}
> +
> +static int thunderx2_uncore_pmu_offline_cpu(unsigned int cpu,
> + struct hlist_node *node)
> +{
> + int new_cpu;
> + struct thunderx2_pmu_uncore_channel *pmu_uncore;
> +
> + pmu_uncore = hlist_entry_safe(node,
> + struct thunderx2_pmu_uncore_channel, node);
> + if (cpu != pmu_uncore->cpu)
> + return 0;
> +
> + new_cpu = cpumask_any_and(
> + cpumask_of_node(pmu_uncore->uncore_dev->node),
> + cpu_online_mask);
> + if (new_cpu >= nr_cpu_ids)
> + return 0;
> +
> + pmu_uncore->cpu = new_cpu;
> + perf_pmu_migrate_context(&pmu_uncore->pmu, cpu, new_cpu);
> + return 0;
> +}
> +
> +static const struct acpi_device_id thunderx2_uncore_acpi_match[] = {
> + {"CAV901C", 0},
> + {},
no ',' required
> +};
> +MODULE_DEVICE_TABLE(acpi, thunderx2_uncore_acpi_match);
> +
> +static int thunderx2_uncore_probe(struct platform_device *pdev)
> +{
> + struct device *dev = &pdev->dev;
> + acpi_handle handle;
> + acpi_status status;
> +
> + set_dev_node(dev, acpi_get_node(ACPI_HANDLE(dev)));
Is this already done when the platform device is created in ACPI
enumeration? I assume the child devices have enumerated at this point.
> +
> + /* Make sure firmware supports DMC/L3C set channel smc call */
> + if (test_uncore_select_channel_early(dev))
> + return -ENODEV;
> +
> + if (!has_acpi_companion(dev))
> + return -ENODEV;
> +
> + handle = ACPI_HANDLE(dev);
> + if (!handle)
> + return -EINVAL;
> +
> + /* Walk through the tree for all PMU UNCORE devices */
> + status = acpi_walk_namespace(ACPI_TYPE_DEVICE, handle, 1,
> + thunderx2_pmu_uncore_dev_add,
> + NULL, dev, NULL);
> + if (ACPI_FAILURE(status)) {
> + dev_err(dev, "failed to probe PMU devices\n");
> + return_ACPI_STATUS(status);
> + }
> +
> + dev_info(dev, "node%d: pmu uncore registered\n", dev_to_node(dev));
> + return 0;
> +}
> +
> +static struct platform_driver thunderx2_uncore_driver = {
> + .probe = thunderx2_uncore_probe,
why no remove?
> + .driver = {
> + .name = "thunderx2-uncore-pmu",
> + .acpi_match_table = ACPI_PTR(thunderx2_uncore_acpi_match),
> + },
> +};
> +
> +static int __init register_thunderx2_uncore_driver(void)
> +{
> + int ret;
> +
> + ret = cpuhp_setup_state_multi(CPUHP_AP_PERF_ARM_THUNDERX2_UNCORE_ONLINE,
> + "perf/tx2/uncore:online",
> + NULL,
> + thunderx2_uncore_pmu_offline_cpu);
> + if (ret)
> + return ret;
> +
> + return platform_driver_register(&thunderx2_uncore_driver);
> +
> +}
> +device_initcall(register_thunderx2_uncore_driver);
> diff --git a/include/linux/cpuhotplug.h b/include/linux/cpuhotplug.h
> index 8796ba3..eb0c896 100644
> --- a/include/linux/cpuhotplug.h
> +++ b/include/linux/cpuhotplug.h
> @@ -161,6 +161,7 @@ enum cpuhp_state {
> CPUHP_AP_PERF_ARM_L2X0_ONLINE,
> CPUHP_AP_PERF_ARM_QCOM_L2_ONLINE,
> CPUHP_AP_PERF_ARM_QCOM_L3_ONLINE,
> + CPUHP_AP_PERF_ARM_THUNDERX2_UNCORE_ONLINE,
> CPUHP_AP_PERF_POWERPC_NEST_IMC_ONLINE,
> CPUHP_AP_PERF_POWERPC_CORE_IMC_ONLINE,
> CPUHP_AP_PERF_POWERPC_THREAD_IMC_ONLINE,
>
More information about the linux-arm-kernel
mailing list