[PATCH 1/5] phy: allwinner: add phy driver for USB3 PHY on Allwinner H6 SoC
Icenowy Zheng
icenowy at aosc.io
Mon May 7 08:18:13 PDT 2018
Allwinner H6 SoC contains a USB3 PHY (with USB2 DP/DM lines also
controlled).
Add a driver for it.
The register operations in this driver is mainly extracted from the BSP
USB3 driver.
Signed-off-by: Icenowy Zheng <icenowy at aosc.io>
---
.../bindings/phy/sun50i-usb3-phy.txt | 24 +++
drivers/phy/allwinner/Kconfig | 13 ++
drivers/phy/allwinner/Makefile | 1 +
drivers/phy/allwinner/phy-sun50i-usb3.c | 195 ++++++++++++++++++
4 files changed, 233 insertions(+)
create mode 100644 Documentation/devicetree/bindings/phy/sun50i-usb3-phy.txt
create mode 100644 drivers/phy/allwinner/phy-sun50i-usb3.c
diff --git a/Documentation/devicetree/bindings/phy/sun50i-usb3-phy.txt b/Documentation/devicetree/bindings/phy/sun50i-usb3-phy.txt
new file mode 100644
index 000000000000..912d55f9f69d
--- /dev/null
+++ b/Documentation/devicetree/bindings/phy/sun50i-usb3-phy.txt
@@ -0,0 +1,24 @@
+Allwinner sun50i USB3 PHY
+-----------------------
+
+Required properties:
+- compatible : should be one of
+ * allwinner,sun60i-h6-usb3-phy
+- reg : a list of offset + length pairs
+- #phy-cells : from the generic phy bindings, must be 0
+- clocks : phandle + clock specifier for the phy clock
+- resets : phandle + reset specifier for the phy reset
+
+Optional Properties:
+- phy-supply : from the generic phy bindings, a phandle to a regulator that
+ provides power to VBUS.
+
+Example:
+ usb3phy: phy at 5210000 {
+ compatible = "allwinner,sun50i-h6-usb3-phy";
+ reg = <0x5210000 0x10000>;
+ clocks = <&ccu CLK_USB_PHY1>;
+ resets = <&ccu RST_USB_PHY1>;
+ #phy-cells = <0>;
+ status = "disabled";
+ };
diff --git a/drivers/phy/allwinner/Kconfig b/drivers/phy/allwinner/Kconfig
index cdc1e745ba47..cf373bcee034 100644
--- a/drivers/phy/allwinner/Kconfig
+++ b/drivers/phy/allwinner/Kconfig
@@ -29,3 +29,16 @@ config PHY_SUN9I_USB
sun9i SoCs.
This driver controls each individual USB 2 host PHY.
+
+config PHY_SUN50I_USB3
+ tristate "Allwinner sun50i SoC USB3 PHY driver"
+ depends on ARCH_SUNXI && HAS_IOMEM && OF
+ depends on RESET_CONTROLLER
+ depends on USB_SUPPORT
+ select USB_COMMON
+ select GENERIC_PHY
+ help
+ Enable this to support the USB3.0-capable transceiver that is
+ part of some Allwinner sun50i SoCs.
+
+ This driver controls each individual USB 2+3 host PHY combo.
diff --git a/drivers/phy/allwinner/Makefile b/drivers/phy/allwinner/Makefile
index 8605529c01a1..a8d01e9073c2 100644
--- a/drivers/phy/allwinner/Makefile
+++ b/drivers/phy/allwinner/Makefile
@@ -1,2 +1,3 @@
obj-$(CONFIG_PHY_SUN4I_USB) += phy-sun4i-usb.o
obj-$(CONFIG_PHY_SUN9I_USB) += phy-sun9i-usb.o
+obj-$(CONFIG_PHY_SUN50I_USB3) += phy-sun50i-usb3.o
diff --git a/drivers/phy/allwinner/phy-sun50i-usb3.c b/drivers/phy/allwinner/phy-sun50i-usb3.c
new file mode 100644
index 000000000000..000a3e04e6d1
--- /dev/null
+++ b/drivers/phy/allwinner/phy-sun50i-usb3.c
@@ -0,0 +1,194 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Allwinner sun50i(H6) USB 3.0 phy driver
+ *
+ * Copyright (C) 2017 Icenowy Zheng <icenowy at aosc.io>
+ *
+ * Based on phy-sun9i-usb.c, which is:
+ *
+ * Copyright (C) 2014-2015 Chen-Yu Tsai <wens at csie.org>
+ *
+ * Based on code from Allwinner BSP, which is:
+ *
+ * Copyright (c) 2010-2015 Allwinner Technology Co., Ltd.
+ */
+
+#include <linux/clk.h>
+#include <linux/err.h>
+#include <linux/io.h>
+#include <linux/module.h>
+#include <linux/phy/phy.h>
+#include <linux/usb/of.h>
+#include <linux/platform_device.h>
+#include <linux/reset.h>
+
+/* Interface Status and Control Registers */
+#define SUNXI_ISCR 0x00
+#define SUNXI_PIPE_CLOCK_CONTROL 0x14
+#define SUNXI_PHY_TUNE_LOW 0x18
+#define SUNXI_PHY_TUNE_HIGH 0x1c
+#define SUNXI_PHY_EXTERNAL_CONTROL 0x20
+
+/* USB2.0 Interface Status and Control Register */
+#define SUNXI_ISCR_FORCE_VBUS (3 << 12)
+
+/* PIPE Clock Control Register */
+#define SUNXI_PCC_PIPE_CLK_OPEN (1 << 6)
+
+/* PHY External Control Register */
+#define SUNXI_PEC_EXTERN_VBUS (3 << 1)
+#define SUNXI_PEC_SSC_EN (1 << 24)
+#define SUNXI_PEC_REF_SSP_EN (1 << 26)
+
+/* PHY Tune High Register */
+#define SUNXI_TX_DEEMPH_3P5DB(n) ((n) << 19)
+#define SUNXI_TX_DEEMPH_3P5DB_MASK GENMASK(24, 19)
+#define SUNXI_TX_DEEMPH_6DB(n) ((n) << 13)
+#define SUNXI_TX_DEEMPH_6GB_MASK GENMASK(18, 13)
+#define SUNXI_TX_SWING_FULL(n) ((n) << 6)
+#define SUNXI_TX_SWING_FULL_MASK GENMASK(12, 6)
+#define SUNXI_LOS_BIAS(n) ((n) << 3)
+#define SUNXI_LOS_BIAS_MASK GENMASK(5, 3)
+#define SUNXI_TXVBOOSTLVL(n) ((n) << 0)
+#define SUNXI_TXVBOOSTLVL_MASK GENMASK(0, 2)
+
+struct sun50i_usb3_phy {
+ struct phy *phy;
+ void __iomem *regs;
+ struct reset_control *reset;
+ struct clk *clk;
+};
+
+static void sun50i_usb3_phy_open(struct sun50i_usb3_phy *phy)
+{
+ u32 val;
+
+ val = readl(phy->regs + SUNXI_PHY_EXTERNAL_CONTROL);
+ val |= SUNXI_PEC_EXTERN_VBUS;
+ val |= SUNXI_PEC_SSC_EN | SUNXI_PEC_REF_SSP_EN;
+ writel(val, phy->regs + SUNXI_PHY_EXTERNAL_CONTROL);
+
+ val = readl(phy->regs + SUNXI_PIPE_CLOCK_CONTROL);
+ val |= SUNXI_PCC_PIPE_CLK_OPEN;
+ writel(val, phy->regs + SUNXI_PIPE_CLOCK_CONTROL);
+
+ val = readl(phy->regs + SUNXI_ISCR);
+ val |= SUNXI_ISCR_FORCE_VBUS;
+ writel(val, phy->regs + SUNXI_ISCR);
+
+ /*
+ * All the magic numbers written to the PHY_TUNE_{LOW_HIGH}
+ * registers are directly taken from the BSP USB3 driver from
+ * Allwiner.
+ */
+ writel(0x0047fc87, phy->regs + SUNXI_PHY_TUNE_LOW);
+
+ val = readl(phy->regs + SUNXI_PHY_TUNE_HIGH);
+ val &= ~(SUNXI_TXVBOOSTLVL_MASK | SUNXI_LOS_BIAS_MASK |
+ SUNXI_TX_SWING_FULL_MASK | SUNXI_TX_DEEMPH_6GB_MASK |
+ SUNXI_TX_DEEMPH_3P5DB_MASK);
+ val |= SUNXI_TXVBOOSTLVL(0x7);
+ val |= SUNXI_LOS_BIAS(0x7);
+ val |= SUNXI_TX_SWING_FULL(0x55);
+ val |= SUNXI_TX_DEEMPH_6DB(0x20);
+ val |= SUNXI_TX_DEEMPH_3P5DB(0x15);
+ writel(val, phy->regs + SUNXI_PHY_TUNE_HIGH);
+}
+
+static int sun50i_usb3_phy_init(struct phy *_phy)
+{
+ struct sun50i_usb3_phy *phy = phy_get_drvdata(_phy);
+ int ret;
+
+ ret = clk_prepare_enable(phy->clk);
+ if (ret)
+ goto err_clk;
+
+ ret = reset_control_deassert(phy->reset);
+ if (ret)
+ goto err_reset;
+
+ sun50i_usb3_phy_open(phy);
+ return 0;
+
+err_reset:
+ clk_disable_unprepare(phy->clk);
+
+err_clk:
+ return ret;
+}
+
+static int sun50i_usb3_phy_exit(struct phy *_phy)
+{
+ struct sun50i_usb3_phy *phy = phy_get_drvdata(_phy);
+
+ reset_control_assert(phy->reset);
+ clk_disable_unprepare(phy->clk);
+
+ return 0;
+}
+
+static const struct phy_ops sun50i_usb3_phy_ops = {
+ .init = sun50i_usb3_phy_init,
+ .exit = sun50i_usb3_phy_exit,
+ .owner = THIS_MODULE,
+};
+
+static int sun50i_usb3_phy_probe(struct platform_device *pdev)
+{
+ struct sun50i_usb3_phy *phy;
+ struct device *dev = &pdev->dev;
+ struct phy_provider *phy_provider;
+ struct resource *res;
+
+ phy = devm_kzalloc(dev, sizeof(*phy), GFP_KERNEL);
+ if (!phy)
+ return -ENOMEM;
+
+ phy->clk = devm_clk_get(dev, NULL);
+ if (IS_ERR(phy->clk)) {
+ dev_err(dev, "failed to get phy clock\n");
+ return PTR_ERR(phy->clk);
+ }
+
+ phy->reset = devm_reset_control_get(dev, NULL);
+ if (IS_ERR(phy->reset)) {
+ dev_err(dev, "failed to get reset control\n");
+ return PTR_ERR(phy->reset);
+ }
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ phy->regs = devm_ioremap_resource(dev, res);
+ if (IS_ERR(phy->regs))
+ return PTR_ERR(phy->regs);
+
+ phy->phy = devm_phy_create(dev, NULL, &sun50i_usb3_phy_ops);
+ if (IS_ERR(phy->phy)) {
+ dev_err(dev, "failed to create PHY\n");
+ return PTR_ERR(phy->phy);
+ }
+
+ phy_set_drvdata(phy->phy, phy);
+ phy_provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate);
+
+ return PTR_ERR_OR_ZERO(phy_provider);
+}
+
+static const struct of_device_id sun50i_usb3_phy_of_match[] = {
+ { .compatible = "allwinner,sun50i-h6-usb3-phy" },
+ { },
+};
+MODULE_DEVICE_TABLE(of, sun50i_usb3_phy_of_match);
+
+static struct platform_driver sun50i_usb3_phy_driver = {
+ .probe = sun50i_usb3_phy_probe,
+ .driver = {
+ .of_match_table = sun50i_usb3_phy_of_match,
+ .name = "sun50i-usb3-phy",
+ }
+};
+module_platform_driver(sun50i_usb3_phy_driver);
+
+MODULE_DESCRIPTION("Allwinner sun50i USB 3.0 phy driver");
+MODULE_AUTHOR("Icenowy Zheng <icenowy at aosc.io>");
+MODULE_LICENSE("GPL");
--
2.17.0
More information about the linux-arm-kernel
mailing list