[PATCH V6 4/7] ARM: dts: imx6sx-sabreauto: add fec support

[Anson Huang]

Add FEC support on i.MX6SX Sabre Auto board.

Signed-off-by: Fugang Duan <fugang.duan at nxp.com>
Signed-off-by: Anson Huang <Anson.Huang at nxp.com>
---
changes since V5:
	use "gpios" instead of "enable-gpio".
 arch/arm/boot/dts/imx6sx-sabreauto.dts | 80 ++++++++++++++++++++++++++++++++++
 1 file changed, 80 insertions(+)

diff --git a/arch/arm/boot/dts/imx6sx-sabreauto.dts b/arch/arm/boot/dts/imx6sx-sabreauto.dts
index 4d41b4d..7dda741 100644
--- a/arch/arm/boot/dts/imx6sx-sabreauto.dts
+++ b/arch/arm/boot/dts/imx6sx-sabreauto.dts
@@ -18,6 +18,17 @@
 		reg = <0x80000000 0x80000000>;
 	};
 
+	reg_fec: fec_io_supply {
+		compatible = "regulator-gpio";
+		regulator-name = "1.8V_1.5V_FEC";
+		regulator-min-microvolt = <1500000>;
+		regulator-max-microvolt = <1800000>;
+		states = <1500000 0x0 1800000 0x1>;
+		gpios = <&max7322 0 GPIO_ACTIVE_HIGH>;
+		vin-supply = <&sw2_reg>;
+		enable-active-high;
+	};
+
 	vcc_sd3: regulator-vcc-sd3 {
 		compatible = "regulator-fixed";
 		pinctrl-names = "default";
@@ -34,6 +45,39 @@
 	clock-frequency = <24576000>;
 };
 
+&fec1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet1>;
+	phy-mode = "rgmii";
+	phy-handle = <&ethphy1>;
+	fsl,magic-packet;
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy0: ethernet-phy at 0 {
+			compatible = "ethernet-phy-ieee802.3-c22";
+			reg = <0>;
+		};
+
+		ethphy1: ethernet-phy at 1 {
+			compatible = "ethernet-phy-ieee802.3-c22";
+			reg = <1>;
+		};
+	};
+};
+
+&fec2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet2>;
+	phy-mode = "rgmii";
+	phy-handle = <&ethphy0>;
+	fsl,magic-packet;
+	status = "okay";
+};
+
 &uart1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_uart1>;
@@ -66,6 +110,42 @@
 };
 
 &iomuxc {
+	pinctrl_enet1: enet1grp {
+		fsl,pins = <
+			MX6SX_PAD_ENET1_MDIO__ENET1_MDIO        0xa0b1
+			MX6SX_PAD_ENET1_MDC__ENET1_MDC          0xa0b1
+			MX6SX_PAD_RGMII1_TXC__ENET1_RGMII_TXC   0xa0b9
+			MX6SX_PAD_RGMII1_TD0__ENET1_TX_DATA_0   0xa0b1
+			MX6SX_PAD_RGMII1_TD1__ENET1_TX_DATA_1   0xa0b1
+			MX6SX_PAD_RGMII1_TD2__ENET1_TX_DATA_2   0xa0b1
+			MX6SX_PAD_RGMII1_TD3__ENET1_TX_DATA_3   0xa0b1
+			MX6SX_PAD_RGMII1_TX_CTL__ENET1_TX_EN    0xa0b1
+			MX6SX_PAD_RGMII1_RXC__ENET1_RX_CLK      0x3081
+			MX6SX_PAD_RGMII1_RD0__ENET1_RX_DATA_0   0x3081
+			MX6SX_PAD_RGMII1_RD1__ENET1_RX_DATA_1   0x3081
+			MX6SX_PAD_RGMII1_RD2__ENET1_RX_DATA_2   0x3081
+			MX6SX_PAD_RGMII1_RD3__ENET1_RX_DATA_3   0x3081
+			MX6SX_PAD_RGMII1_RX_CTL__ENET1_RX_EN    0x3081
+		>;
+	};
+
+	pinctrl_enet2: enet2grp {
+		fsl,pins = <
+			MX6SX_PAD_RGMII2_TXC__ENET2_RGMII_TXC   0xa0b9
+			MX6SX_PAD_RGMII2_TD0__ENET2_TX_DATA_0   0xa0b1
+			MX6SX_PAD_RGMII2_TD1__ENET2_TX_DATA_1   0xa0b1
+			MX6SX_PAD_RGMII2_TD2__ENET2_TX_DATA_2   0xa0b1
+			MX6SX_PAD_RGMII2_TD3__ENET2_TX_DATA_3   0xa0b1
+			MX6SX_PAD_RGMII2_TX_CTL__ENET2_TX_EN    0xa0b1
+			MX6SX_PAD_RGMII2_RXC__ENET2_RX_CLK      0x3081
+			MX6SX_PAD_RGMII2_RD0__ENET2_RX_DATA_0   0x3081
+			MX6SX_PAD_RGMII2_RD1__ENET2_RX_DATA_1   0x3081
+			MX6SX_PAD_RGMII2_RD2__ENET2_RX_DATA_2   0x3081
+			MX6SX_PAD_RGMII2_RD3__ENET2_RX_DATA_3   0x3081
+			MX6SX_PAD_RGMII2_RX_CTL__ENET2_RX_EN    0x3081
+		>;
+	};
+
 	pinctrl_i2c2: i2c2grp {
 		fsl,pins = <
 			MX6SX_PAD_GPIO1_IO03__I2C2_SDA          0x4001b8b1
-- 
2.7.4