[PATCH v9 07/27] ARM: davinci: dm355: add new clock init using common clock framework
Sekhar Nori
nsekhar at ti.com
Fri May 4 03:01:53 PDT 2018
On Thursday 03 May 2018 09:14 PM, David Lechner wrote:
> On 05/03/2018 10:34 AM, Sekhar Nori wrote:
>> On Friday 27 April 2018 05:47 AM, David Lechner wrote:
>>> This adds the new board-specific clock init in mach-davinci/dm355.c
>>> using the new common clock framework drivers.
>>>
>>> The #ifdefs are needed to prevent compile errors until the entire
>>> ARCH_DAVINCI is converted.
>>>
>>> Also clean up the #includes since we are adding some here.
>>>
>>> Signed-off-by: David Lechner <david at lechnology.com>
>>
>> I am having trouble booting DM355 EVM with the series applied.
>> Still to debug what is going wrong.
>
> Can you dump the PLL registers using /sys/kernel/debug/clk/... ?
I was able to get to ramdisk shell if I set clk_ignore_unused. Here is
the dump:
root at dm355-evm:/sys/kernel/debug# cat clk/clk_summary
enable prepare protect
clock count count count rate accuracy phase
----------------------------------------------------------------------------------------
ref_clk 1 1 0 24000000 0 0
oscin 3 3 0 24000000 0 0
pll2_sysclkbp 0 0 0 3000000 0 0
pll2_prediv 2 2 0 3000000 0 0
pll2_pllout 1 1 0 342000000 0 0
pll2_postdiv 1 1 0 342000000 0 0
pll2_pllen 0 0 0 342000000 0 0
pll1_sysclkbp 0 0 0 8000000 0 0
pll1_auxclk 4 5 0 24000000 0 0
timer2 1 4 0 24000000 0 0
timer1 0 0 0 24000000 0 0
timer0 2 2 0 24000000 0 0
pwm2 0 0 0 24000000 0 0
pwm1 0 0 0 24000000 0 0
pwm0 0 0 0 24000000 0 0
uart1 1 4 0 24000000 0 0
uart0 1 4 0 24000000 0 0
i2c 0 3 0 24000000 0 0
rto 0 0 0 24000000 0 0
pwm3 0 0 0 24000000 0 0
timer3 0 0 0 24000000 0 0
pll1_prediv 2 2 0 3000000 0 0
pll1_pllout 1 1 0 432000000 0 0
pll1_postdiv 1 1 0 432000000 0 0
pll1_pllen 0 0 0 432000000 0 0
pll2_sysclk2 1 1 0 0 0 0
pll2_sysclk1 0 0 0 0 0 0
pll1_sysclk4 1 3 0 0 0 0
vpss_slave 0 1 0 0 0 0
vpss_master 0 1 0 0 0 0
pll1_sysclk3 1 1 0 0 0 0
vpss_dac 0 0 0 0 0 0
pll1_sysclk2 4 5 0 0 0 0
gpio 1 1 0 0 0 0
spi0 0 3 0 0 0 0
uart2 1 4 0 0 0 0
asp0 0 0 0 0 0 0
mmcsd0 0 0 0 0 0 0
aemif 1 1 0 0 0 0
spi2 0 0 0 0 0 0
usb 0 0 0 0 0 0
asp1 0 0 0 0 0 0
mmcsd1 0 0 0 0 0 0
spi1 0 0 0 0 0 0
pll1_sysclk1 2 2 0 0 0 0
mjcp 0 0 0 0 0 0
arm 1 1 0 0 0 0
and the dump with current master:
root at dm355-evm:/sys/kernel/debug# cat davinci_clocks
ref_clk users= 7 24000000 Hz
pll1 users= 7 pll 432000000 Hz
pll1_sysclk1 users= 1 pll 216000000 Hz
arm_clk users= 1 psc 216000000 Hz
mjcp users= 0 psc 216000000 Hz
pll1_sysclk2 users= 3 pll 108000000 Hz
uart2 users= 1 psc 108000000 Hz
asp0 users= 0 psc 108000000 Hz
asp1 users= 0 psc 108000000 Hz
mmcsd0 users= 0 psc 108000000 Hz
mmcsd1 users= 0 psc 108000000 Hz
spi0 users= 0 psc 108000000 Hz
spi1 users= 0 psc 108000000 Hz
spi2 users= 0 psc 108000000 Hz
gpio users= 1 psc 108000000 Hz
aemif users= 1 psc 108000000 Hz
usb users= 0 psc 108000000 Hz
pll1_sysclk3 users= 0 pll 27000000 Hz
vpss_dac users= 0 psc 27000000 Hz
pll1_sysclk4 users= 0 pll 108000000 Hz
vpss_master users= 0 psc 108000000 Hz
vpss_slave users= 0 psc 108000000 Hz
pll1_aux_clk users= 3 pll 24000000 Hz
clkout1 users= 0 24000000 Hz
uart0 users= 1 psc 24000000 Hz
uart1 users= 1 psc 24000000 Hz
i2c users= 0 psc 24000000 Hz
pwm0 users= 0 psc 24000000 Hz
pwm1 users= 0 psc 24000000 Hz
pwm2 users= 0 psc 24000000 Hz
pwm3 users= 0 psc 24000000 Hz
timer0 users= 1 psc 24000000 Hz
timer1 users= 0 psc 24000000 Hz
timer2 users= 1 psc 24000000 Hz
timer3 users= 0 psc 24000000 Hz
rto users= 0 psc 24000000 Hz
pll1_sysclkbp users= 0 pll 8000000 Hz
clkout2 users= 0 8000000 Hz
pll2 users= 0 pll 342000000 Hz
pll2_sysclk1 users= 0 pll 342000000 Hz
pll2_sysclkbp users= 0 pll 3000000 Hz
clkout3 users= 0 3000000 Hz
I didn't have time today to analyze these myself. Hope it helps.
Thanks,
Sekhar
More information about the linux-arm-kernel
mailing list