[PATCH 1/2] dt-bindings: add MediaTek XS-PHY binding
Chunfeng Yun
chunfeng.yun at mediatek.com
Wed May 2 00:04:20 PDT 2018
Hi Rob,
On Tue, 2018-05-01 at 09:24 -0500, Rob Herring wrote:
> On Wed, Apr 25, 2018 at 03:45:28PM +0800, Chunfeng Yun wrote:
> > Add a DT binding documentation of XS-PHY for MediaTek SoCs
> > with USB3.1 GEN2 controller
> >
> > Signed-off-by: Chunfeng Yun <chunfeng.yun at mediatek.com>
> > ---
> > .../devicetree/bindings/phy/phy-mtk-xsphy.txt | 127 ++++++++++++++++++++
> > 1 file changed, 127 insertions(+)
> > create mode 100644 Documentation/devicetree/bindings/phy/phy-mtk-xsphy.txt
> >
> > diff --git a/Documentation/devicetree/bindings/phy/phy-mtk-xsphy.txt b/Documentation/devicetree/bindings/phy/phy-mtk-xsphy.txt
> > new file mode 100644
> > index 0000000..23c51a0
> > --- /dev/null
> > +++ b/Documentation/devicetree/bindings/phy/phy-mtk-xsphy.txt
> > @@ -0,0 +1,127 @@
> > +MediaTek XS-PHY binding
> > +--------------------------
> > +
> > +The XS-PHY controller supports physical layer functionality for USB3.1
> > +GEN2 controller on MediaTek SoCs.
> > +
> > +Required properties (controller (parent) node):
> > + - compatible : should be "mediatek,<soc-model>-xsphy", "mediatek,xsphy",
> > + soc-model is the name of SoC, such as mt2712 etc;
>
> Please list all valid SoCs.
Ok
>
> > + when using "mediatek,xsphy" compatible string, you need SoC specific
> > + ones in addition.
> > +
> > +Required nodes : a sub-node is required for each port the controller
> > + provides. Address range information including the usual
> > + 'reg' property is used inside these nodes to describe
> > + the controller's topology.
>
> This should go afer the parent optional properties.
Ok
>
> > +
> > +Optional properties (controller (parent) node):
> > + - reg : offset and length of register shared by multiple U3 ports,
> > + exclude port's private register, if only U2 ports provided,
> > + shouldn't use the property.
> > + - mediatek,src-ref-clk-mhz : u32, frequency of reference clock for slew rate
> > + calibrate
> > + - mediatek,src-coef : u32, coefficient for slew rate calibrate, depends on
> > + SoC process
> > +
> > +Required properties (port (child) node):
> > +- reg : address and length of the register set for the port.
> > +- clocks : a list of phandle + clock-specifier pairs, one for each
> > + entry in clock-names
> > +- clock-names : must contain
> > + "ref": 48M reference clock for HighSpeed analog phy; and 26M
> > + reference clock for SuperSpeedPlus analog phy, sometimes is
> > + 24M, 25M or 27M, depended on platform.
> > +- #phy-cells : should be 1 (See second example)
> > + cell after port phandle is phy type from:
> > + - PHY_TYPE_USB2
> > + - PHY_TYPE_USB3
>
> Is the type a property of the connection to the host? If not, this
> shouldn't be part of the phy cells. I would add compatible strings to
> the child nodes to define this. I think that would simplify the driver
> too as then you can parse DT properties in probe rather than phy_init.
Yes, it is.
It's parsed when the phy is got by the host driver.
>
> > +
> > +The following optional properties are only for debug or HQA test
> > +Optional properties (PHY_TYPE_USB2 port (child) node):
> > +- mediatek,eye-src : u32, the value of slew rate calibrate
> > +- mediatek,eye-vrt : u32, the selection of VRT reference voltage
> > +- mediatek,eye-term : u32, the selection of HS_TX TERM reference voltage
> > +- mediatek,efuse-intr : u32, the selection of Internal Resistor
> > +
> > +Optional properties (PHY_TYPE_USB3 port (child) node):
> > +- mediatek,efuse-intr : u32, the selection of Internal Resistor
> > +- mediatek,efuse-tx-imp : u32, the selection of TX Impedance
> > +- mediatek,efuse-rx-imp : u32, the selection of RX Impedance
> > +
> > +Example:
> > +
> > +u3phy: usb-phy at 11c40000 {
> > + compatible = "mediatek,mt36xx-xsphy", "mediatek,xsphy";
>
> Is mt36xx a specific SoC? Don't use wildcards in compatible strings.
No, will use a specific one
>
> > + reg = <0 0x11c43000 0 0x0200>;
> > + mediatek,src-ref-clk-mhz = <26>;
> > + mediatek,src-coef = <17>;
> > + #address-cells = <2>;
> > + #size-cells = <2>;
>
> Really need 64-bit sizes?
Just an example, 32-bit is also ok, but it's better to use the same
value as the root node
>
> > + ranges;
>
> Limiting the range to only the phy addresses is preferred.
>
> > + status = "disabled";
>
> Don't show status in examples.
Ok
>
> > +
> > + u2port0: usb-phy at 11c40000 {
> > + reg = <0 0x11c40000 0 0x0400>;
> > + clocks = <&clk48m>;
> > + clock-names = "ref";
> > + mediatek,eye-src = <4>;
> > + #phy-cells = <1>;
> > + status = "okay";
> > + };
> > +
> > + u3port0: usb-phy at 11c43000 {
> > + reg = <0 0x11c43400 0 0x0500>;
> > + clocks = <&clk26m>;
> > + clock-names = "ref";
> > + mediatek,efuse-intr = <28>;
> > + #phy-cells = <1>;
> > + status = "okay";
> > + };
> > +};
> > +
>
> > +Specifying phy control of devices
> > +---------------------------------
> > +
> > +Device nodes should specify the configuration required in their "phys"
> > +property, containing a phandle to the phy port node and a device type;
> > +phy-names for each port are optional.
> > +
> > +Example:
> > +
> > +#include <dt-bindings/phy/phy.h>
> > +
> > +ssusb: usb at 112a0000 {
> > + ...
> > + phys = <&u2port0 PHY_TYPE_USB2>, <&u3port0 PHY_TYPE_USB3>;
> > + phy-names = "usb2-0", "usb3-0";
> > + ...
> > +};
>
> This section is not necessary. We've already explained how to use the
> phy binding elsewhere.
Will remove it in next version
>
> > +
> > +
> > +Banks layout of xsphy
>
> Put this before the example.
Ok
Thanks a lot.
>
> > +-------------------------------------------------------------
> > +port offset bank
> > +u2 port0 0x0000 MISC
> > + 0x0100 FMREG
> > + 0x0300 U2PHY_COM
> > +u2 port1 0x1000 MISC
> > + 0x1100 FMREG
> > + 0x1300 U2PHY_COM
> > +u2 port2 0x2000 MISC
> > + ...
> > +u31 common 0x3000 DIG_GLB
> > + 0x3100 PHYA_GLB
> > +u31 port0 0x3400 DIG_LN_TOP
> > + 0x3500 DIG_LN_TX0
> > + 0x3600 DIG_LN_RX0
> > + 0x3700 DIG_LN_DAIF
> > + 0x3800 PHYA_LN
> > +u31 port1 0x3a00 DIG_LN_TOP
> > + 0x3b00 DIG_LN_TX0
> > + 0x3c00 DIG_LN_RX0
> > + 0x3d00 DIG_LN_DAIF
> > + 0x3e00 PHYA_LN
> > + ...
> > +
> > +DIG_GLB & PHYA_GLB are shared by U31 ports.
> > --
> > 1.7.9.5
> >
More information about the linux-arm-kernel
mailing list