[PATCH v5 4/9] dt-bindings: gpio: Add gpio nodes for Actions S900 SoC

[Manivannan Sadhasivam]

Hi Rob,

On Sun, Mar 18, 2018 at 07:53:04AM -0500, Rob Herring wrote:
> On Fri, Mar 09, 2018 at 10:43:40AM +0530, Manivannan Sadhasivam wrote:
> > Add gpio nodes for Actions Semi S900 SoC.
> > 
> > Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam at linaro.org>
> > ---
> >  .../devicetree/bindings/gpio/actions,owl-gpio.txt  | 90 ++++++++++++++++++++++
> >  1 file changed, 90 insertions(+)
> >  create mode 100644 Documentation/devicetree/bindings/gpio/actions,owl-gpio.txt
> > 
> > diff --git a/Documentation/devicetree/bindings/gpio/actions,owl-gpio.txt b/Documentation/devicetree/bindings/gpio/actions,owl-gpio.txt
> > new file mode 100644
> > index 000000000000..ad7d32ce2abe
> > --- /dev/null
> > +++ b/Documentation/devicetree/bindings/gpio/actions,owl-gpio.txt
> > @@ -0,0 +1,90 @@
> > +* Actions Semi OWL GPIO controller bindings
> > +
> > +The GPIOs are organized as individual banks/ports with variable number
> > +of GPIOs. Each bank is represented as an individual GPIO controller.
> > +
> > +Required properties:
> > +- compatible            : Should be "actions,s900-gpio"
> > +- reg                   : Address and range of the GPIO controller registers.
> > +- gpio-controller       : Marks the device node as a GPIO controller.
> > +- #gpio-cells           : Should be <2>. The first cell is the gpio number
> > +                          and the second cell is used to specify optional
> > +                          parameters.
> > +- ngpios                : Specifies the number of GPIO lines.
> > +- interrupt-controller  : Marks the device node as an interrupt controller.
> > +- #interrupt-cells      : Specifies the number of cells needed to encode an
> > +                          interrupt.  Shall be set to 2.  The first cell
> > +                          defines the interrupt number, the second encodes
> > +                          the trigger flags described in
> > +                          bindings/interrupt-controller/interrupts.txt
> > +
> > +Optional properties:
> > +- gpio-ranges           : Mapping between GPIO and pinctrl
> > +
> > +Examples:
> > +
> > +       gpioa: gpio at e01b0000 {
> > +               compatible = "actions,s900-gpio";
> > +               reg = <0x0 0xe01b0000 0x0 0x1000>;
> > +               gpio-controller;
> > +               #gpio-cells = <2>;
> > +               gpio-ranges = <&pinctrl 0 0 32>;
> > +               ngpios = <32>;
> 
> This is only needed if the number of gpios is reduced for some reason 
> such as not pinned out. IOW, 32 is implied because that's the size of 
> each bank.
> 

Okay. Then I can remove ngpio property for banks which has 32 GPIOs.

> > +               interrupt-controller;
> > +               #interrupt-cells = <2>;
> > +       };
> > +
> > +       gpiob: gpio at e01b000c {
> > +               compatible = "actions,s900-gpio";
> > +               reg = <0x0 0xe01b000c 0x0 0x1000>;
> 
> Due to the sizes, these are still overlapping.
> 

Oops, will fix the size.

Thanks,
Mani

> Rob
> 
> > +               gpio-controller;
> > +               #gpio-cells = <2>;
> > +               gpio-ranges = <&pinctrl 0 32 32>;
> > +               ngpios = <32>;
> > +               interrupt-controller;
> > +               #interrupt-cells = <2>;
> > +       };