[PATCH v2 02/13] ARM: dts: ipq4019: Add a few peripheral nodes

[Abhishek Sahu]

On 2018-03-16 15:08, Sricharan R wrote:
> Now with the driver updates for some peripherals being there,
> add i2c, spi, pcie, bam, qpic-nand, scm nodes to enhance the available
> peripheral support.
> 
> Signed-off-by: Sricharan R <sricharan at codeaurora.org>

Reviwed-by: Abhishek Sahu <absahu at codeaurora.org>

> ---
>  arch/arm/boot/dts/qcom-ipq4019.dtsi | 134 
> ++++++++++++++++++++++++++++++++++++
>  1 file changed, 134 insertions(+)
> 
> diff --git a/arch/arm/boot/dts/qcom-ipq4019.dtsi
> b/arch/arm/boot/dts/qcom-ipq4019.dtsi
> index 10d112a..e38fffa 100644
> --- a/arch/arm/boot/dts/qcom-ipq4019.dtsi
> +++ b/arch/arm/boot/dts/qcom-ipq4019.dtsi
> @@ -25,7 +25,9 @@
> 
>  	aliases {
>  		spi0 = &spi_0;
> +		spi1 = &spi_1;
>  		i2c0 = &i2c_0;
> +		i2c1 = &i2c_1;
>  	};
> 
>  	cpus {
> @@ -104,6 +106,12 @@
>  		};
>  	};
> 
> +	firmware {
> +		scm {
> +			compatible = "qcom,scm-ipq4019";
> +		};
> +	};
> +
>  	timer {
>  		compatible = "arm,armv7-timer";
>  		interrupts = <1 2 0xf08>,
> @@ -172,6 +180,22 @@
>  			clock-names = "core", "iface";
>  			#address-cells = <1>;
>  			#size-cells = <0>;
> +			dmas = <&blsp_dma 5>, <&blsp_dma 4>;
> +			dma-names = "rx", "tx";
> +			status = "disabled";
> +		};
> +
> +		spi_1: spi at 78b6000 { /* BLSP1 QUP2 */
> +			compatible = "qcom,spi-qup-v2.2.1";
> +			reg = <0x78b6000 0x600>;
> +			interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
> +			clocks = <&gcc GCC_BLSP1_QUP2_SPI_APPS_CLK>,
> +				<&gcc GCC_BLSP1_AHB_CLK>;
> +			clock-names = "core", "iface";
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +			dmas = <&blsp_dma 7>, <&blsp_dma 6>;
> +			dma-names = "rx", "tx";
>  			status = "disabled";
>  		};
> 
> @@ -184,9 +208,24 @@
>  			clock-names = "iface", "core";
>  			#address-cells = <1>;
>  			#size-cells = <0>;
> +			dmas = <&blsp_dma 9>, <&blsp_dma 8>;
> +			dma-names = "rx", "tx";
>  			status = "disabled";
>  		};
> 
> +		i2c_1: i2c at 78b8000 { /* BLSP1 QUP4 */
> +			compatible = "qcom,i2c-qup-v2.2.1";
> +			reg = <0x78b8000 0x600>;
> +			interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
> +			clocks = <&gcc GCC_BLSP1_AHB_CLK>,
> +				 <&gcc GCC_BLSP1_QUP2_I2C_APPS_CLK>;
> +			clock-names = "iface", "core";
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +			dmas = <&blsp_dma 11>, <&blsp_dma 10>;
> +			dma-names = "rx", "tx";
> +			status = "disabled";
> +		};
> 
>  		cryptobam: dma at 8e04000 {
>  			compatible = "qcom,bam-v1.7.0";
> @@ -293,6 +332,101 @@
>  			reg = <0x4ab000 0x4>;
>  		};
> 
> +		pcie0: pci at 40000000 {
> +			compatible = "qcom,pcie-ipq4019", "snps,dw-pcie";
> +			reg =  <0x40000000 0xf1d
> +				0x40000f20 0xa8
> +				0x80000 0x2000
> +				0x40100000 0x1000>;
> +			reg-names = "dbi", "elbi", "parf", "config";
> +			device_type = "pci";
> +			linux,pci-domain = <0>;
> +			bus-range = <0x00 0xff>;
> +			num-lanes = <1>;
> +			#address-cells = <3>;
> +			#size-cells = <2>;
> +
> +			ranges = <0x81000000 0 0x40200000 0x40200000 0 0x00100000
> +				  0x82000000 0 0x48000000 0x48000000 0 0x10000000>;
> +
> +			interrupts = <GIC_SPI 141 IRQ_TYPE_NONE>;
> +			interrupt-names = "msi";
> +			#interrupt-cells = <1>;
> +			interrupt-map-mask = <0 0 0 0x7>;
> +			interrupt-map = <0 0 0 1 &intc 0 142 IRQ_TYPE_LEVEL_HIGH>, /* int_a 
> */
> +					<0 0 0 2 &intc 0 143 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
> +					<0 0 0 3 &intc 0 144 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
> +					<0 0 0 4 &intc 0 145 IRQ_TYPE_LEVEL_HIGH>; /* int_d */
> +			clocks = <&gcc GCC_PCIE_AHB_CLK>,
> +				 <&gcc GCC_PCIE_AXI_M_CLK>,
> +				 <&gcc GCC_PCIE_AXI_S_CLK>;
> +			clock-names = "aux",
> +				      "master_bus",
> +				      "slave_bus";
> +
> +			resets = <&gcc PCIE_AXI_M_ARES>,
> +				 <&gcc PCIE_AXI_S_ARES>,
> +				 <&gcc PCIE_PIPE_ARES>,
> +				 <&gcc PCIE_AXI_M_VMIDMT_ARES>,
> +				 <&gcc PCIE_AXI_S_XPU_ARES>,
> +				 <&gcc PCIE_PARF_XPU_ARES>,
> +				 <&gcc PCIE_PHY_ARES>,
> +				 <&gcc PCIE_AXI_M_STICKY_ARES>,
> +				 <&gcc PCIE_PIPE_STICKY_ARES>,
> +				 <&gcc PCIE_PWR_ARES>,
> +				 <&gcc PCIE_AHB_ARES>,
> +				 <&gcc PCIE_PHY_AHB_ARES>;
> +			reset-names = "axi_m",
> +				      "axi_s",
> +				      "pipe",
> +				      "axi_m_vmid",
> +				      "axi_s_xpu",
> +				      "parf",
> +				      "phy",
> +				      "axi_m_sticky",
> +				      "pipe_sticky",
> +				      "pwr",
> +				      "ahb",
> +				      "phy_ahb";
> +
> +			status = "disabled";
> +		};
> +
> +		qpic_bam: dma at 7984000 {
> +			compatible = "qcom,bam-v1.7.0";
> +			reg = <0x7984000 0x1a000>;
> +			interrupts = <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>;
> +			clocks = <&gcc GCC_QPIC_CLK>;
> +			clock-names = "bam_clk";
> +			#dma-cells = <1>;
> +			qcom,ee = <0>;
> +			status = "disabled";
> +		};
> +
> +		nand: qpic-nand at 79b0000 {
> +			compatible = "qcom,ipq4019-nand";
> +			reg = <0x79b0000 0x1000>;
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +			clocks = <&gcc GCC_QPIC_CLK>,
> +				 <&gcc GCC_QPIC_AHB_CLK>;
> +			clock-names = "core", "aon";
> +
> +			dmas = <&qpic_bam 0>,
> +			       <&qpic_bam 1>,
> +			       <&qpic_bam 2>;
> +			dma-names = "tx", "rx", "cmd";
> +			status = "disabled";
> +
> +			nand at 0 {
> +				reg = <0>;
> +
> +				nand-ecc-strength = <4>;
> +				nand-ecc-step-size = <512>;
> +				nand-bus-width = <8>;
> +			};
> +		};
> +
>  		wifi0: wifi at a000000 {
>  			compatible = "qcom,ipq4019-wifi";
>  			reg = <0xa000000 0x200000>;