[PATCH V6 2/2] thermal: imx: add i.MX7 thermal sensor support
Zhang Rui
rui.zhang at intel.com
Mon Mar 12 23:51:05 PDT 2018
yeah, will review it and get back to you later.
On 二, 2018-03-13 at 06:13 +0000, Anson Huang wrote:
> Ping...
>
> @rui.zhang at intel.com, can you help review this patch?
>
> Anson Huang
> Best Regards!
>
>
> >
> > -----Original Message-----
> > From: linux-arm-kernel [mailto:linux-arm-kernel-bounces at lists.infra
> > dead.org]
> > On Behalf Of Anson Huang
> > Sent: Friday, March 2, 2018 10:00 AM
> > To: Leonard Crestez <leonard.crestez at nxp.com>; rui.zhang at intel.com;
> > edubezval at gmail.com; robh+dt at kernel.org; mark.rutland at arm.com;
> > shawnguo at kernel.org; kernel at pengutronix.de; Fabio Estevam
> > <fabio.estevam at nxp.com>; linux at armlinux.org.uk
> > Cc: linux-arm-kernel at lists.infradead.org; devicetree at vger.kernel.or
> > g;
> > dl-linux-imx <linux-imx at nxp.com>; linux-kernel at vger.kernel.org;
> > linux-pm at vger.kernel.org
> > Subject: [PATCH V6 2/2] thermal: imx: add i.MX7 thermal sensor
> > support
> >
> > This patch adds i.MX7 thermal sensor support, most of the i.MX7
> > thermal sensor
> > functions are same with
> > i.MX6 except the registers offset/layout, so we move those
> > registers
> > offset/layout definitions to soc data structure.
> >
> > i.MX7 uses single calibration data @25C, the calibration data is
> > located at
> > OCOTP offset 0x4F0, bit[17:9], the formula is as below:
> >
> > Tmeas = (Nmeas - n1) + 25; n1 is the fuse value for 25C.
> >
> > Signed-off-by: Anson Huang <Anson.Huang at nxp.com>
> > Signed-off-by: Bai Ping <ping.bai at nxp.com>
> > Acked-by: Dong Aisheng <aisheng.dong at nxp.com>
> > Acked-by: Shawn Guo <shawnguo at kernel.org>
> > Reviewed-by: Rob Herring <robh at kernel.org>
> > ---
> > changes since V5:
> > no code change, just add Reviewed-by.
> > .../devicetree/bindings/thermal/imx-thermal.txt | 9 +-
> > drivers/thermal/imx_thermal.c | 295
> > ++++++++++++++++-----
> > 2 files changed, 239 insertions(+), 65 deletions(-)
> >
> > diff --git a/Documentation/devicetree/bindings/thermal/imx-
> > thermal.txt
> > b/Documentation/devicetree/bindings/thermal/imx-thermal.txt
> > index 28be51a..38bffcc 100644
> > --- a/Documentation/devicetree/bindings/thermal/imx-thermal.txt
> > +++ b/Documentation/devicetree/bindings/thermal/imx-thermal.txt
> > @@ -1,8 +1,13 @@
> > * Temperature Monitor (TEMPMON) on Freescale i.MX SoCs
> >
> > Required properties:
> > -- compatible : "fsl,imx6q-tempmon" for i.MX6Q, "fsl,imx6sx-
> > tempmon" for
> > i.MX6SX.
> > - i.MX6SX has two more IRQs than i.MX6Q, one is IRQ_LOW and the
> > other is
> > IRQ_PANIC,
> > +- compatible : must be one of following:
> > + - "fsl,imx6q-tempmon" for i.MX6Q,
> > + - "fsl,imx6sx-tempmon" for i.MX6SX,
> > + - "fsl,imx7d-tempmon" for i.MX7S/D.
> > +- interrupts : the interrupt output of the controller:
> > + i.MX6Q has one IRQ which will be triggered when temperature is
> > higher
> > +than high threshold,
> > + i.MX6SX and i.MX7S/D have two more IRQs than i.MX6Q, one is
> > IRQ_LOW
> > +and the other is IRQ_PANIC,
> > when temperature is below than low threshold, IRQ_LOW will be
> > triggered,
> > when temperature
> > is higher than panic threshold, system will auto reboot by SRC
> > module.
> > - fsl,tempmon : phandle pointer to system controller that contains
> > TEMPMON
> > diff --git a/drivers/thermal/imx_thermal.c
> > b/drivers/thermal/imx_thermal.c
> > index a67781b..569d41b 100644
> > --- a/drivers/thermal/imx_thermal.c
> > +++ b/drivers/thermal/imx_thermal.c
> > @@ -31,35 +31,57 @@
> > #define REG_CLR 0x8
> > #define REG_TOG 0xc
> >
> > -#define MISC0 0x0150
> > -#define MISC0_REFTOP_SELBIASOFF (1 << 3)
> > -#define MISC1 0x0160
> > -#define MISC1_IRQ_TEMPHIGH (1 << 29)
> > +/* i.MX6 specific */
> > +#define IMX6_MISC0 0x0150
> > +#define IMX6_MISC0_REFTOP_SELBIASOFF (1 << 3)
> > +#define IMX6_MISC1 0x0160
> > +#define IMX6_MISC1_IRQ_TEMPHIGH (1 << 29)
> > /* Below LOW and PANIC bits are only for TEMPMON_IMX6SX */
> > -#define MISC1_IRQ_TEMPLOW (1 << 28)
> > -#define MISC1_IRQ_TEMPPANIC (1 << 27)
> > -
> > -#define TEMPSENSE0 0x0180
> > -#define TEMPSENSE0_ALARM_VALUE_SHIFT 20
> > -#define TEMPSENSE0_ALARM_VALUE_MASK (0xfff <<
> > TEMPSENSE0_ALARM_VALUE_SHIFT)
> > -#define TEMPSENSE0_TEMP_CNT_SHIFT 8
> > -#define TEMPSENSE0_TEMP_CNT_MASK (0xfff <<
> > TEMPSENSE0_TEMP_CNT_SHIFT)
> > -#define TEMPSENSE0_FINISHED (1 << 2)
> > -#define TEMPSENSE0_MEASURE_TEMP (1 << 1)
> > -#define TEMPSENSE0_POWER_DOWN (1 << 0)
> > -
> > -#define TEMPSENSE1 0x0190
> > -#define TEMPSENSE1_MEASURE_FREQ 0xffff
> > -/* Below TEMPSENSE2 is only for TEMPMON_IMX6SX */
> > -#define TEMPSENSE2 0x0290
> > -#define TEMPSENSE2_LOW_VALUE_SHIFT 0
> > -#define TEMPSENSE2_LOW_VALUE_MASK 0xfff
> > -#define TEMPSENSE2_PANIC_VALUE_SHIFT 16
> > -#define TEMPSENSE2_PANIC_VALUE_MASK 0xfff0000
> > +#define IMX6_MISC1_IRQ_TEMPLOW (1 << 28)
> > +#define IMX6_MISC1_IRQ_TEMPPANIC (1 << 27)
> > +
> > +#define IMX6_TEMPSENSE0 0x0180
> > +#define IMX6_TEMPSENSE0_ALARM_VALUE_SHIFT 20
> > +#define IMX6_TEMPSENSE0_ALARM_VALUE_MASK (0xfff << 20)
> > +#define IMX6_TEMPSENSE0_TEMP_CNT_SHIFT 8
> > +#define IMX6_TEMPSENSE0_TEMP_CNT_MASK (0xfff << 8)
> > +#define IMX6_TEMPSENSE0_FINISHED (1 << 2)
> > +#define IMX6_TEMPSENSE0_MEASURE_TEMP (1 << 1)
> > +#define IMX6_TEMPSENSE0_POWER_DOWN (1 << 0)
> > +
> > +#define IMX6_TEMPSENSE1 0x0190
> > +#define IMX6_TEMPSENSE1_MEASURE_FREQ 0xffff
> > +#define IMX6_TEMPSENSE1_MEASURE_FREQ_SHIFT 0
> >
> > #define OCOTP_MEM0 0x0480
> > #define OCOTP_ANA1 0x04e0
> >
> > +/* Below TEMPSENSE2 is only for TEMPMON_IMX6SX */
> > +#define IMX6_TEMPSENSE2 0x0290
> > +#define IMX6_TEMPSENSE2_LOW_VALUE_SHIFT 0
> > +#define IMX6_TEMPSENSE2_LOW_VALUE_MASK 0xfff
> > +#define IMX6_TEMPSENSE2_PANIC_VALUE_SHIFT 16
> > +#define IMX6_TEMPSENSE2_PANIC_VALUE_MASK 0xfff0000
> > +
> > +/* i.MX7 specific */
> > +#define IMX7_ANADIG_DIGPROG 0x800
> > +#define IMX7_TEMPSENSE0 0x300
> > +#define IMX7_TEMPSENSE0_PANIC_ALARM_SHIFT 18
> > +#define IMX7_TEMPSENSE0_PANIC_ALARM_MASK (0x1ff << 18)
> > +#define IMX7_TEMPSENSE0_HIGH_ALARM_SHIFT 9
> > +#define IMX7_TEMPSENSE0_HIGH_ALARM_MASK (0x1ff <<
> > 9)
> > +#define IMX7_TEMPSENSE0_LOW_ALARM_SHIFT 0
> > +#define IMX7_TEMPSENSE0_LOW_ALARM_MASK 0x1ff
> > +
> > +#define IMX7_TEMPSENSE1 0x310
> > +#define IMX7_TEMPSENSE1_MEASURE_FREQ_SHIFT 16
> > +#define IMX7_TEMPSENSE1_MEASURE_FREQ_MASK (0xffff << 16)
> > +#define IMX7_TEMPSENSE1_FINISHED (1 << 11)
> > +#define IMX7_TEMPSENSE1_MEASURE_TEMP (1 << 10)
> > +#define IMX7_TEMPSENSE1_POWER_DOWN (1 << 9)
> > +#define IMX7_TEMPSENSE1_TEMP_VALUE_SHIFT 0
> > +#define IMX7_TEMPSENSE1_TEMP_VALUE_MASK 0x1ff
> > +
> > /* The driver supports 1 passive trip point and 1 critical trip
> > point */ enum
> > imx_thermal_trip {
> > IMX_TRIP_PASSIVE,
> > @@ -72,17 +94,114 @@ enum imx_thermal_trip {
> >
> > #define TEMPMON_IMX6Q 1
> > #define TEMPMON_IMX6SX 2
> > +#define TEMPMON_IMX7D 3
> >
> > struct thermal_soc_data {
> > u32 version;
> > +
> > + u32 sensor_ctrl;
> > + u32 power_down_mask;
> > + u32 measure_temp_mask;
> > +
> > + u32 measure_freq_ctrl;
> > + u32 measure_freq_mask;
> > + u32 measure_freq_shift;
> > +
> > + u32 temp_data;
> > + u32 temp_value_mask;
> > + u32 temp_value_shift;
> > + u32 temp_valid_mask;
> > +
> > + u32 panic_alarm_ctrl;
> > + u32 panic_alarm_mask;
> > + u32 panic_alarm_shift;
> > +
> > + u32 high_alarm_ctrl;
> > + u32 high_alarm_mask;
> > + u32 high_alarm_shift;
> > +
> > + u32 low_alarm_ctrl;
> > + u32 low_alarm_mask;
> > + u32 low_alarm_shift;
> > };
> >
> > static struct thermal_soc_data thermal_imx6q_data = {
> > .version = TEMPMON_IMX6Q,
> > +
> > + .sensor_ctrl = IMX6_TEMPSENSE0,
> > + .power_down_mask = IMX6_TEMPSENSE0_POWER_DOWN,
> > + .measure_temp_mask = IMX6_TEMPSENSE0_MEASURE_TEMP,
> > +
> > + .measure_freq_ctrl = IMX6_TEMPSENSE1,
> > + .measure_freq_shift = IMX6_TEMPSENSE1_MEASURE_FREQ_SHIFT,
> > + .measure_freq_mask = IMX6_TEMPSENSE1_MEASURE_FREQ,
> > +
> > + .temp_data = IMX6_TEMPSENSE0,
> > + .temp_value_mask = IMX6_TEMPSENSE0_TEMP_CNT_MASK,
> > + .temp_value_shift = IMX6_TEMPSENSE0_TEMP_CNT_SHIFT,
> > + .temp_valid_mask = IMX6_TEMPSENSE0_FINISHED,
> > +
> > + .high_alarm_ctrl = IMX6_TEMPSENSE0,
> > + .high_alarm_mask = IMX6_TEMPSENSE0_ALARM_VALUE_MASK,
> > + .high_alarm_shift = IMX6_TEMPSENSE0_ALARM_VALUE_SHIFT,
> > };
> >
> > static struct thermal_soc_data thermal_imx6sx_data = {
> > .version = TEMPMON_IMX6SX,
> > +
> > + .sensor_ctrl = IMX6_TEMPSENSE0,
> > + .power_down_mask = IMX6_TEMPSENSE0_POWER_DOWN,
> > + .measure_temp_mask = IMX6_TEMPSENSE0_MEASURE_TEMP,
> > +
> > + .measure_freq_ctrl = IMX6_TEMPSENSE1,
> > + .measure_freq_shift = IMX6_TEMPSENSE1_MEASURE_FREQ_SHIFT,
> > + .measure_freq_mask = IMX6_TEMPSENSE1_MEASURE_FREQ,
> > +
> > + .temp_data = IMX6_TEMPSENSE0,
> > + .temp_value_mask = IMX6_TEMPSENSE0_TEMP_CNT_MASK,
> > + .temp_value_shift = IMX6_TEMPSENSE0_TEMP_CNT_SHIFT,
> > + .temp_valid_mask = IMX6_TEMPSENSE0_FINISHED,
> > +
> > + .high_alarm_ctrl = IMX6_TEMPSENSE0,
> > + .high_alarm_mask = IMX6_TEMPSENSE0_ALARM_VALUE_MASK,
> > + .high_alarm_shift = IMX6_TEMPSENSE0_ALARM_VALUE_SHIFT,
> > +
> > + .panic_alarm_ctrl = IMX6_TEMPSENSE2,
> > + .panic_alarm_mask = IMX6_TEMPSENSE2_PANIC_VALUE_MASK,
> > + .panic_alarm_shift = IMX6_TEMPSENSE2_PANIC_VALUE_SHIFT,
> > +
> > + .low_alarm_ctrl = IMX6_TEMPSENSE2,
> > + .low_alarm_mask = IMX6_TEMPSENSE2_LOW_VALUE_MASK,
> > + .low_alarm_shift = IMX6_TEMPSENSE2_LOW_VALUE_SHIFT, };
> > +
> > +static struct thermal_soc_data thermal_imx7d_data = {
> > + .version = TEMPMON_IMX7D,
> > +
> > + .sensor_ctrl = IMX7_TEMPSENSE1,
> > + .power_down_mask = IMX7_TEMPSENSE1_POWER_DOWN,
> > + .measure_temp_mask = IMX7_TEMPSENSE1_MEASURE_TEMP,
> > +
> > + .measure_freq_ctrl = IMX7_TEMPSENSE1,
> > + .measure_freq_shift = IMX7_TEMPSENSE1_MEASURE_FREQ_SHIFT,
> > + .measure_freq_mask = IMX7_TEMPSENSE1_MEASURE_FREQ_MASK,
> > +
> > + .temp_data = IMX7_TEMPSENSE1,
> > + .temp_value_mask = IMX7_TEMPSENSE1_TEMP_VALUE_MASK,
> > + .temp_value_shift = IMX7_TEMPSENSE1_TEMP_VALUE_SHIFT,
> > + .temp_valid_mask = IMX7_TEMPSENSE1_FINISHED,
> > +
> > + .panic_alarm_ctrl = IMX7_TEMPSENSE1,
> > + .panic_alarm_mask = IMX7_TEMPSENSE0_PANIC_ALARM_MASK,
> > + .panic_alarm_shift = IMX7_TEMPSENSE0_PANIC_ALARM_SHIFT,
> > +
> > + .high_alarm_ctrl = IMX7_TEMPSENSE0,
> > + .high_alarm_mask = IMX7_TEMPSENSE0_HIGH_ALARM_MASK,
> > + .high_alarm_shift = IMX7_TEMPSENSE0_HIGH_ALARM_SHIFT,
> > +
> > + .low_alarm_ctrl = IMX7_TEMPSENSE0,
> > + .low_alarm_mask = IMX7_TEMPSENSE0_LOW_ALARM_MASK,
> > + .low_alarm_shift = IMX7_TEMPSENSE0_LOW_ALARM_SHIFT,
> > };
> >
> > struct imx_thermal_data {
> > @@ -107,31 +226,42 @@ struct imx_thermal_data { static void
> > imx_set_panic_temp(struct imx_thermal_data *data,
> > int panic_temp)
> > {
> > + const struct thermal_soc_data *soc_data = data->socdata;
> > struct regmap *map = data->tempmon;
> > int critical_value;
> >
> > critical_value = (data->c2 - panic_temp) / data->c1;
> > - regmap_write(map, TEMPSENSE2 + REG_CLR,
> > TEMPSENSE2_PANIC_VALUE_MASK);
> > - regmap_write(map, TEMPSENSE2 + REG_SET, critical_value <<
> > - TEMPSENSE2_PANIC_VALUE_SHIFT);
> > +
> > + regmap_write(map, soc_data->panic_alarm_ctrl + REG_CLR,
> > + soc_data->panic_alarm_mask);
> > + regmap_write(map, soc_data->panic_alarm_ctrl + REG_SET,
> > + critical_value << soc_data-
> > >panic_alarm_shift);
> > }
> >
> > static void imx_set_alarm_temp(struct imx_thermal_data *data,
> > int alarm_temp)
> > {
> > struct regmap *map = data->tempmon;
> > + const struct thermal_soc_data *soc_data = data->socdata;
> > int alarm_value;
> >
> > data->alarm_temp = alarm_temp;
> > - alarm_value = (data->c2 - alarm_temp) / data->c1;
> > - regmap_write(map, TEMPSENSE0 + REG_CLR,
> > TEMPSENSE0_ALARM_VALUE_MASK);
> > - regmap_write(map, TEMPSENSE0 + REG_SET, alarm_value <<
> > - TEMPSENSE0_ALARM_VALUE_SHIFT);
> > +
> > + if (data->socdata->version == TEMPMON_IMX7D)
> > + alarm_value = alarm_temp / 1000 + data->c1 - 25;
> > + else
> > + alarm_value = (data->c2 - alarm_temp) / data->c1;
> > +
> > + regmap_write(map, soc_data->high_alarm_ctrl + REG_CLR,
> > + soc_data->high_alarm_mask);
> > + regmap_write(map, soc_data->high_alarm_ctrl + REG_SET,
> > + alarm_value << soc_data->high_alarm_shift);
> > }
> >
> > static int imx_get_temp(struct thermal_zone_device *tz, int
> > *temp) {
> > struct imx_thermal_data *data = tz->devdata;
> > + const struct thermal_soc_data *soc_data = data->socdata;
> > struct regmap *map = data->tempmon;
> > unsigned int n_meas;
> > bool wait;
> > @@ -139,16 +269,18 @@ static int imx_get_temp(struct
> > thermal_zone_device
> > *tz, int *temp)
> >
> > if (data->mode == THERMAL_DEVICE_ENABLED) {
> > /* Check if a measurement is currently in progress
> > */
> > - regmap_read(map, TEMPSENSE0, &val);
> > - wait = !(val & TEMPSENSE0_FINISHED);
> > + regmap_read(map, soc_data->temp_data, &val);
> > + wait = !(val & soc_data->temp_valid_mask);
> > } else {
> > /*
> > * Every time we measure the temperature, we will
> > power on the
> > * temperature sensor, enable measurements, take a
> > reading,
> > * disable measurements, power off the temperature
> > sensor.
> > */
> > - regmap_write(map, TEMPSENSE0 + REG_CLR,
> > TEMPSENSE0_POWER_DOWN);
> > - regmap_write(map, TEMPSENSE0 + REG_SET,
> > TEMPSENSE0_MEASURE_TEMP);
> > + regmap_write(map, soc_data->sensor_ctrl + REG_CLR,
> > + soc_data->power_down_mask);
> > + regmap_write(map, soc_data->sensor_ctrl + REG_SET,
> > + soc_data->measure_temp_mask);
> >
> > wait = true;
> > }
> > @@ -160,22 +292,28 @@ static int imx_get_temp(struct
> > thermal_zone_device
> > *tz, int *temp)
> > if (wait)
> > usleep_range(20, 50);
> >
> > - regmap_read(map, TEMPSENSE0, &val);
> > + regmap_read(map, soc_data->temp_data, &val);
> >
> > if (data->mode != THERMAL_DEVICE_ENABLED) {
> > - regmap_write(map, TEMPSENSE0 + REG_CLR,
> > TEMPSENSE0_MEASURE_TEMP);
> > - regmap_write(map, TEMPSENSE0 + REG_SET,
> > TEMPSENSE0_POWER_DOWN);
> > + regmap_write(map, soc_data->sensor_ctrl + REG_CLR,
> > + soc_data->measure_temp_mask);
> > + regmap_write(map, soc_data->sensor_ctrl + REG_SET,
> > + soc_data->power_down_mask);
> > }
> >
> > - if ((val & TEMPSENSE0_FINISHED) == 0) {
> > + if ((val & soc_data->temp_valid_mask) == 0) {
> > dev_dbg(&tz->device, "temp measurement never
> > finished\n");
> > return -EAGAIN;
> > }
> >
> > - n_meas = (val & TEMPSENSE0_TEMP_CNT_MASK) >>
> > TEMPSENSE0_TEMP_CNT_SHIFT;
> > + n_meas = (val & soc_data->temp_value_mask)
> > + >> soc_data->temp_value_shift;
> >
> > /* See imx_init_calib() for formula derivation */
> > - *temp = data->c2 - n_meas * data->c1;
> > + if (data->socdata->version == TEMPMON_IMX7D)
> > + *temp = (n_meas - data->c1 + 25) * 1000;
> > + else
> > + *temp = data->c2 - n_meas * data->c1;
> >
> > /* Update alarm value to next higher trip point for
> > TEMPMON_IMX6Q */
> > if (data->socdata->version == TEMPMON_IMX6Q) { @@ -219,21
> > +357,26
> > @@ static int imx_set_mode(struct thermal_zone_device *tz, {
> > struct imx_thermal_data *data = tz->devdata;
> > struct regmap *map = data->tempmon;
> > + const struct thermal_soc_data *soc_data = data->socdata;
> >
> > if (mode == THERMAL_DEVICE_ENABLED) {
> > tz->polling_delay = IMX_POLLING_DELAY;
> > tz->passive_delay = IMX_PASSIVE_DELAY;
> >
> > - regmap_write(map, TEMPSENSE0 + REG_CLR,
> > TEMPSENSE0_POWER_DOWN);
> > - regmap_write(map, TEMPSENSE0 + REG_SET,
> > TEMPSENSE0_MEASURE_TEMP);
> > + regmap_write(map, soc_data->sensor_ctrl + REG_CLR,
> > + soc_data->power_down_mask);
> > + regmap_write(map, soc_data->sensor_ctrl + REG_SET,
> > + soc_data->measure_temp_mask);
> >
> > if (!data->irq_enabled) {
> > data->irq_enabled = true;
> > enable_irq(data->irq);
> > }
> > } else {
> > - regmap_write(map, TEMPSENSE0 + REG_CLR,
> > TEMPSENSE0_MEASURE_TEMP);
> > - regmap_write(map, TEMPSENSE0 + REG_SET,
> > TEMPSENSE0_POWER_DOWN);
> > + regmap_write(map, soc_data->sensor_ctrl + REG_CLR,
> > + soc_data->measure_temp_mask);
> > + regmap_write(map, soc_data->sensor_ctrl + REG_SET,
> > + soc_data->power_down_mask);
> >
> > tz->polling_delay = 0;
> > tz->passive_delay = 0;
> > @@ -355,6 +498,15 @@ static int imx_init_calib(struct
> > platform_device *pdev,
> > u32 ocotp_ana1)
> > }
> >
> > /*
> > + * On i.MX7D, we only use the calibration data at 25C to
> > get the temp,
> > + * Tmeas = ( Nmeas - n1) + 25; n1 is the fuse value for
> > 25C.
> > + */
> > + if (data->socdata->version == TEMPMON_IMX7D) {
> > + data->c1 = (ocotp_ana1 >> 9) & 0x1ff;
> > + return 0;
> > + }
> > +
> > + /*
> > * The sensor is calibrated at 25 °C (aka T1) and the
> > value measured
> > * (aka N1) at this temperature is provided in bits
> > [31:20] in the
> > * i.MX's OCOTP value ANA1.
> > @@ -492,6 +644,7 @@ static irqreturn_t
> > imx_thermal_alarm_irq_thread(int
> > irq, void *dev) static const struct of_device_id
> > of_imx_thermal_match[] = {
> > { .compatible = "fsl,imx6q-tempmon", .data =
> > &thermal_imx6q_data, },
> > { .compatible = "fsl,imx6sx-tempmon", .data =
> > &thermal_imx6sx_data, },
> > + { .compatible = "fsl,imx7d-tempmon", .data =
> > &thermal_imx7d_data, },
> > { /* end */ }
> > };
> > MODULE_DEVICE_TABLE(of, of_imx_thermal_match); @@ -523,14 +676,15
> > @@ static int imx_thermal_probe(struct platform_device *pdev)
> >
> > /* make sure the IRQ flag is clear before enabling irq on
> > i.MX6SX */
> > if (data->socdata->version == TEMPMON_IMX6SX) {
> > - regmap_write(map, MISC1 + REG_CLR,
> > MISC1_IRQ_TEMPHIGH |
> > - MISC1_IRQ_TEMPLOW | MISC1_IRQ_TEMPPANIC);
> > + regmap_write(map, IMX6_MISC1 + REG_CLR,
> > + IMX6_MISC1_IRQ_TEMPHIGH |
> > IMX6_MISC1_IRQ_TEMPLOW
> > + | IMX6_MISC1_IRQ_TEMPPANIC);
> > /*
> > * reset value of LOW ALARM is incorrect, set it
> > to lowest
> > * value to avoid false trigger of low alarm.
> > */
> > - regmap_write(map, TEMPSENSE2 + REG_SET,
> > - TEMPSENSE2_LOW_VALUE_MASK);
> > + regmap_write(map, data->socdata->low_alarm_ctrl +
> > REG_SET,
> > + data->socdata->low_alarm_mask);
> > }
> >
> > data->irq = platform_get_irq(pdev, 0); @@ -557,11 +711,17
> > @@ static int
> > imx_thermal_probe(struct platform_device *pdev)
> > }
> >
> > /* Make sure sensor is in known good state for
> > measurements */
> > - regmap_write(map, TEMPSENSE0 + REG_CLR,
> > TEMPSENSE0_POWER_DOWN);
> > - regmap_write(map, TEMPSENSE0 + REG_CLR,
> > TEMPSENSE0_MEASURE_TEMP);
> > - regmap_write(map, TEMPSENSE1 + REG_CLR,
> > TEMPSENSE1_MEASURE_FREQ);
> > - regmap_write(map, MISC0 + REG_SET,
> > MISC0_REFTOP_SELBIASOFF);
> > - regmap_write(map, TEMPSENSE0 + REG_SET,
> > TEMPSENSE0_POWER_DOWN);
> > + regmap_write(map, data->socdata->sensor_ctrl + REG_CLR,
> > + data->socdata->power_down_mask);
> > + regmap_write(map, data->socdata->sensor_ctrl + REG_CLR,
> > + data->socdata->measure_temp_mask);
> > + regmap_write(map, data->socdata->measure_freq_ctrl +
> > REG_CLR,
> > + data->socdata->measure_freq_mask);
> > + if (data->socdata->version != TEMPMON_IMX7D)
> > + regmap_write(map, IMX6_MISC0 + REG_SET,
> > + IMX6_MISC0_REFTOP_SELBIASOFF);
> > + regmap_write(map, data->socdata->sensor_ctrl + REG_SET,
> > + data->socdata->power_down_mask);
> >
> > data->policy = cpufreq_cpu_get(0);
> > if (!data->policy) {
> > @@ -626,16 +786,20 @@ static int imx_thermal_probe(struct
> > platform_device
> > *pdev)
> > data->temp_passive / 1000);
> >
> > /* Enable measurements at ~ 10 Hz */
> > - regmap_write(map, TEMPSENSE1 + REG_CLR,
> > TEMPSENSE1_MEASURE_FREQ);
> > + regmap_write(map, data->socdata->measure_freq_ctrl +
> > REG_CLR,
> > + data->socdata->measure_freq_mask);
> > measure_freq = DIV_ROUND_UP(32768, 10); /* 10 Hz */
> > - regmap_write(map, TEMPSENSE1 + REG_SET, measure_freq);
> > + regmap_write(map, data->socdata->measure_freq_ctrl +
> > REG_SET,
> > + measure_freq << data->socdata-
> > >measure_freq_shift);
> > imx_set_alarm_temp(data, data->temp_passive);
> >
> > if (data->socdata->version == TEMPMON_IMX6SX)
> > imx_set_panic_temp(data, data->temp_critical);
> >
> > - regmap_write(map, TEMPSENSE0 + REG_CLR,
> > TEMPSENSE0_POWER_DOWN);
> > - regmap_write(map, TEMPSENSE0 + REG_SET,
> > TEMPSENSE0_MEASURE_TEMP);
> > + regmap_write(map, data->socdata->sensor_ctrl + REG_CLR,
> > + data->socdata->power_down_mask);
> > + regmap_write(map, data->socdata->sensor_ctrl + REG_SET,
> > + data->socdata->measure_temp_mask);
> >
> > ret = devm_request_threaded_irq(&pdev->dev, data->irq,
> > imx_thermal_alarm_irq,
> > imx_thermal_alarm_irq_thread, @@
> > -661,7 +825,8 @@ static int imx_thermal_remove(struct
> > platform_device
> > *pdev)
> > struct regmap *map = data->tempmon;
> >
> > /* Disable measurements */
> > - regmap_write(map, TEMPSENSE0 + REG_SET,
> > TEMPSENSE0_POWER_DOWN);
> > + regmap_write(map, data->socdata->sensor_ctrl + REG_SET,
> > + data->socdata->power_down_mask);
> > if (!IS_ERR(data->thermal_clk))
> > clk_disable_unprepare(data->thermal_clk);
> >
> > @@ -684,8 +849,10 @@ static int imx_thermal_suspend(struct device
> > *dev)
> > * temperature will be read as the thermal sensor is
> > powered
> > * down.
> > */
> > - regmap_write(map, TEMPSENSE0 + REG_CLR,
> > TEMPSENSE0_MEASURE_TEMP);
> > - regmap_write(map, TEMPSENSE0 + REG_SET,
> > TEMPSENSE0_POWER_DOWN);
> > + regmap_write(map, data->socdata->sensor_ctrl + REG_CLR,
> > + data->socdata->measure_temp_mask);
> > + regmap_write(map, data->socdata->sensor_ctrl + REG_SET,
> > + data->socdata->power_down_mask);
> > data->mode = THERMAL_DEVICE_DISABLED;
> > clk_disable_unprepare(data->thermal_clk);
> >
> > @@ -702,8 +869,10 @@ static int imx_thermal_resume(struct device
> > *dev)
> > if (ret)
> > return ret;
> > /* Enabled thermal sensor after resume */
> > - regmap_write(map, TEMPSENSE0 + REG_CLR,
> > TEMPSENSE0_POWER_DOWN);
> > - regmap_write(map, TEMPSENSE0 + REG_SET,
> > TEMPSENSE0_MEASURE_TEMP);
> > + regmap_write(map, data->socdata->sensor_ctrl + REG_CLR,
> > + data->socdata->power_down_mask);
> > + regmap_write(map, data->socdata->sensor_ctrl + REG_SET,
> > + data->socdata->measure_temp_mask);
> > data->mode = THERMAL_DEVICE_ENABLED;
> >
> > return 0;
> > --
> > 2.7.4
> >
> >
> > _______________________________________________
> > linux-arm-kernel mailing list
> > linux-arm-kernel at lists.infradead.org
> > https://emea01.safelinks.protection.outlook.com/?url=http%3A%2F%2Fl
> > ists.infr
> > adead.org%2Fmailman%2Flistinfo%2Flinux-arm-
> > kernel&data=02%7C01%7Cans
> > on.huang%40nxp.com%7C06aac542a9cb445ee0f308d57fe1cbba%7C686ea1d3
> > bc2b4c6fa92cd99c5c301635%7C0%7C0%7C636555530125162768&sdata=GP4
> > UyKpDXyRkmwSIZY9Sb%2BDxO9sPAWCk0O%2FZPYRA0P4%3D&reserved=0
More information about the linux-arm-kernel
mailing list