[PATCH 04/10] ARM: dts: Augment VGA connector bridge on Realview PBX

[Linus Walleij]

The PL111 in the ARM reference platforms are connected to
"panels" that are actually dumb VGA DAC connector bridges.
Now that we can support the proper bridges in the DRM driver,
fix this up.

Cc: Liviu Dudau <liviu.dudau at arm.com>
Cc: Mali DP Maintainers <malidp at foss.arm.com>
Signed-off-by: Linus Walleij <linus.walleij at linaro.org>
---
 arch/arm/boot/dts/arm-realview-pbx.dtsi | 82 ++++++++++++++++++++++-----------
 1 file changed, 55 insertions(+), 27 deletions(-)

diff --git a/arch/arm/boot/dts/arm-realview-pbx.dtsi b/arch/arm/boot/dts/arm-realview-pbx.dtsi
index aeb49c4bd773..10868ba3277f 100644
--- a/arch/arm/boot/dts/arm-realview-pbx.dtsi
+++ b/arch/arm/boot/dts/arm-realview-pbx.dtsi
@@ -34,7 +34,8 @@
 		serial1 = &serial1;
 		serial2 = &serial2;
 		serial3 = &serial3;
-		i2c0 = &i2c;
+		i2c0 = &i2c0;
+		i2c1 = &i2c1;
 	};
 
 	memory {
@@ -158,6 +159,49 @@
 		port1-otg;
 	};
 
+	bridge {
+		compatible = "ti,ths8134a", "ti,ths8134";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port at 0 {
+				reg = <0>;
+
+				vga_bridge_in: endpoint {
+					remote-endpoint = <&clcd_pads>;
+				};
+			};
+
+			port at 1 {
+				reg = <1>;
+
+				vga_bridge_out: endpoint {
+					remote-endpoint = <&vga_con_in>;
+				};
+			};
+		};
+	};
+
+	vga {
+		/*
+		 * This DDC I2C is connected directly to the DVI portions
+		 * of the connector, so it's not really working when the
+		 * monitor is connected to the VGA connector.
+		 */
+		compatible = "vga-connector";
+		ddc-i2c-bus = <&i2c1>;
+
+		port {
+			vga_con_in: endpoint {
+				remote-endpoint = <&vga_bridge_out>;
+			};
+		};
+	};
+
 	soc: soc at 0 {
 		compatible = "arm,realview-pbx-soc", "simple-bus";
 		#address-cells = <1>;
@@ -285,7 +329,7 @@
 					       <&timclk>;
 		};
 
-		i2c: i2c at 10002000 {
+		i2c0: i2c at 10002000 {
 			#address-cells = <1>;
 			#size-cells = <0>;
 			compatible = "arm,versatile-i2c";
@@ -396,7 +440,12 @@
 			clock-names = "apb_pclk";
 		};
 
-		/* DVI serial bus control is at 10016000 */
+		i2c1: i2c at 10016000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "arm,versatile-i2c";
+			reg = <0x10016000 0x1000>;
+		};
 
 		rtc: rtc at 10017000 {
 			compatible = "arm,pl031", "arm,primecell";
@@ -506,36 +555,15 @@
 			interrupt-names = "combined";
 			clocks = <&oscclk4>, <&pclk>;
 			clock-names = "clcdclk", "apb_pclk";
+			/* 1024x768 16bpp @65MHz works fine */
+			max-memory-bandwidth = <95000000>;
 
 			port {
 				clcd_pads: endpoint {
-					remote-endpoint = <&clcd_panel>;
+					remote-endpoint = <&vga_bridge_in>;
 					arm,pl11x,tft-r0g0b0-pads = <0 8 16>;
 				};
 			};
-
-			panel {
-				compatible = "panel-dpi";
-
-				port {
-					clcd_panel: endpoint {
-						remote-endpoint = <&clcd_pads>;
-					};
-				};
-
-				/* Standard 640x480 VGA timings */
-				panel-timing {
-					clock-frequency = <25175000>;
-					hactive = <640>;
-					hback-porch = <48>;
-					hfront-porch = <16>;
-					hsync-len = <96>;
-					vactive = <480>;
-					vback-porch = <33>;
-					vfront-porch = <10>;
-					vsync-len = <2>;
-				};
-			};
 		};
 	};
 };
-- 
2.14.3