[PATCH 01/10] ARM: dts: Augment VGA connector bridge on PB11MPcore

[Linus Walleij]

The PL111 in the ARM reference platforms are connected to
"panels" that are actually dumb VGA DAC connector bridges.
Now that we can support the proper bridges in the DRM driver,
fix this up.

Cc: Liviu Dudau <liviu.dudau at arm.com>
Cc: Mali DP Maintainers <malidp at foss.arm.com>
Signed-off-by: Linus Walleij <linus.walleij at linaro.org>
---
 arch/arm/boot/dts/arm-realview-pb11mp.dts | 78 +++++++++++++++++++++----------
 1 file changed, 53 insertions(+), 25 deletions(-)

diff --git a/arch/arm/boot/dts/arm-realview-pb11mp.dts b/arch/arm/boot/dts/arm-realview-pb11mp.dts
index 3944765ac4b0..36203288de42 100644
--- a/arch/arm/boot/dts/arm-realview-pb11mp.dts
+++ b/arch/arm/boot/dts/arm-realview-pb11mp.dts
@@ -242,6 +242,49 @@
 		bank-width = <4>;
 	};
 
+	bridge {
+		compatible = "ti,ths8134a", "ti,ths8134";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port at 0 {
+				reg = <0>;
+
+				vga_bridge_in: endpoint {
+					remote-endpoint = <&clcd_pads>;
+				};
+			};
+
+			port at 1 {
+				reg = <1>;
+
+				vga_bridge_out: endpoint {
+					remote-endpoint = <&vga_con_in>;
+				};
+			};
+		};
+	};
+
+	vga {
+		/*
+		 * This DDC I2C is connected directly to the DVI portions
+		 * of the connector, so it's not really working when the
+		 * monitor is connected to the VGA connector.
+		 */
+		compatible = "vga-connector";
+		ddc-i2c-bus = <&i2c1>;
+
+		port {
+			vga_con_in: endpoint {
+				remote-endpoint = <&vga_bridge_out>;
+			};
+		};
+	};
+
 	soc {
 		#address-cells = <1>;
 		#size-cells = <1>;
@@ -575,6 +618,13 @@
 			clock-names = "apb_pclk";
 		};
 
+		i2c1: i2c at 10016000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "arm,versatile-i2c";
+			reg = <0x10016000 0x1000>;
+		};
+
 		rtc: rtc at 10017000 {
 			compatible = "arm,pl031", "arm,primecell";
 			reg = <0x10017000 0x1000>;
@@ -609,37 +659,15 @@
 			interrupts = <0 23 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&oscclk4>, <&pclk>;
 			clock-names = "clcdclk", "apb_pclk";
-			max-memory-bandwidth = <130000000>; /* 16bpp @ 63.5MHz */
+			/* 1024x768 16bpp @65MHz works fine */
+			max-memory-bandwidth = <95000000>;
 
 			port {
 				clcd_pads: endpoint {
-					remote-endpoint = <&clcd_panel>;
+					remote-endpoint = <&vga_bridge_in>;
 					arm,pl11x,tft-r0g0b0-pads = <0 8 16>;
 				};
 			};
-
-			panel {
-				compatible = "panel-dpi";
-
-				port {
-					clcd_panel: endpoint {
-						remote-endpoint = <&clcd_pads>;
-					};
-				};
-
-				/* Standard 640x480 VGA timings */
-				panel-timing {
-					clock-frequency = <25175000>;
-					hactive = <640>;
-					hback-porch = <48>;
-					hfront-porch = <16>;
-					hsync-len = <96>;
-					vactive = <480>;
-					vback-porch = <33>;
-					vfront-porch = <10>;
-					vsync-len = <2>;
-				};
-			};
 		};
 
 		/*
-- 
2.14.3