[PATCH 02/12] thermal: exynos: remove parsing of samsung,tmu_default_temp_offset property

[Bartlomiej Zolnierkiewicz]

Trimming (one point based or two points based) is always used for
the temperature calibration and the default non-trimming code should
never be reached.

Modify temp_to_code() and code_to_temp() accordingly (WARN_ON(1)
in the default cases) and then remove no longer needed parsing of
samsung,tmu_default_temp_offset property.

There should be no functional changes caused by this patch.

Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie at samsung.com>
---
 drivers/thermal/samsung/exynos_tmu.c | 6 ++----
 drivers/thermal/samsung/exynos_tmu.h | 2 --
 2 files changed, 2 insertions(+), 6 deletions(-)

diff --git a/drivers/thermal/samsung/exynos_tmu.c b/drivers/thermal/samsung/exynos_tmu.c
index ed805c7..e42a08b 100644
--- a/drivers/thermal/samsung/exynos_tmu.c
+++ b/drivers/thermal/samsung/exynos_tmu.c
@@ -260,7 +260,7 @@ static int temp_to_code(struct exynos_tmu_data *data, u8 temp)
 		temp_code = temp + data->temp_error1 - pdata->first_point_trim;
 		break;
 	default:
-		temp_code = temp + pdata->default_temp_offset;
+		WARN_ON(1);
 		break;
 	}
 
@@ -287,7 +287,7 @@ static int code_to_temp(struct exynos_tmu_data *data, u16 temp_code)
 		temp = temp_code - data->temp_error1 + pdata->first_point_trim;
 		break;
 	default:
-		temp = temp_code - pdata->default_temp_offset;
+		WARN_ON(1);
 		break;
 	}
 
@@ -1164,8 +1164,6 @@ static int exynos_of_sensor_conf(struct device_node *np,
 	pdata->first_point_trim = (u8)value;
 	of_property_read_u32(np, "samsung,tmu_second_point_trim", &value);
 	pdata->second_point_trim = (u8)value;
-	of_property_read_u32(np, "samsung,tmu_default_temp_offset", &value);
-	pdata->default_temp_offset = (u8)value;
 
 	of_property_read_u32(np, "samsung,tmu_cal_type", &pdata->cal_type);
 
diff --git a/drivers/thermal/samsung/exynos_tmu.h b/drivers/thermal/samsung/exynos_tmu.h
index 8c468b6..a7e81b4 100644
--- a/drivers/thermal/samsung/exynos_tmu.h
+++ b/drivers/thermal/samsung/exynos_tmu.h
@@ -50,7 +50,6 @@ enum soc_type {
  * @efuse_value: platform defined fuse value
  * @min_efuse_value: minimum valid trimming data
  * @max_efuse_value: maximum valid trimming data
- * @default_temp_offset: default temperature offset in case of no trimming
  * @cal_type: calibration type for temperature
  *
  * This structure is required for configuration of exynos_tmu driver.
@@ -65,7 +64,6 @@ struct exynos_tmu_platform_data {
 	u32 max_efuse_value;
 	u8 first_point_trim;
 	u8 second_point_trim;
-	u8 default_temp_offset;
 
 	u32 cal_type;
 };
-- 
1.9.1