[PATCH] sound/tlv320dac33: Add device tree support

[Ladislav Michl]

On Tue, Jan 30, 2018 at 11:35:38AM +0100, Pavel Machek wrote:
> On Tue 2018-01-30 11:10:46, Ladislav Michl wrote:
> > On Tue, Jan 30, 2018 at 11:00:23AM +0100, Pavel Machek wrote:
> > > On Tue 2018-01-30 10:38:38, Ladislav Michl wrote:
> > > > On Tue, Jan 30, 2018 at 10:11:02AM +0100, Filip Matijević wrote:
> > > > > Hi,
> > > > > 
> > > 
> > > > > > Well, notice I'm converting existing driver to device tree. And that
> > > > > > one already has GPIO dependency. It is possible that more work needs
> > > > > > to be done there, but that should not be a reason to delay this. Feel
> > > > > > free to help.
> > > > 
> > > > Adding DT properties that need to be maintained for compatibility reasons
> > > > is a bad idea and very good reason to delay merging unfinished stuff.
> > > > And meanwhile it turned out it is not power-gpio :)
> > > 
> > > I believe reset-gpios and power-gpios are commonly used like
> > > this... and that's what the old code does.
> > 
> > Why do you care about old code when introducing new DT property?
> > Either it is reset, then lets call it reset-gpios or it is power supply
> > and then voltage regulator should be used (VAUX4.OUT is such a regulator
> > although it is unclear to me how it is controlled (*)).
> 
> power gpio = !reset gpio. Difference is only in polarity.

Quick grep:
Documentation/devicetree/bindings/net/smsc-lan91c111.txt
- power-gpios: GPIO to control the PWRDWN pin
- reset-gpios: GPIO to control the RESET pin
Documentation/devicetree/bindings/net/wireless/ti,wl1251.txt
- ti,power-gpio :     GPIO connected to chip's PMEN pin
Documentation/devicetree/bindings/input/touchscreen/silead_gsl1680.txt
- power-gpios             : Specification for the pin connected to the gsl1680's
                            shutdown input. This needs to be driven high to take the
                            gsl1680 out of its low power state
Documentation/devicetree/bindings/input/touchscreen/ektf2127.txt
- power-gpios             : GPIO specification for the pin connected to the
                            ektf2127's wake input. This needs to be driven high
                            to take ektf2127 out of it's low power state

As you can see others are using it to drive pins different from nRESET. As
stated in datasheet:
"The TLV320DAC32 requires a hardware reset after power-up for proper operation.
After all power supplies are at their specified values, the nRESET pin must be
driven low for at least 10ns. If this reset sequence is not performed, the DAC32
may not respond properly to register reads/writes". That does not sound like
anything to do with power.

(It seems the only difference between TLV320DAC33 and TLV320DAC32 is uses a ball
grid array package vs QFN32)

> > > You are not helping.
> > 
> > The only way I can help here is to resend your patch with "reset-gpios"
> > used, which I'm pretty sure you can handle yourself.
> 
> Well, you can do that, and then you can argue with the next person who
> feels one of the properties has to get his preferred color. Hard part
> is not changing code :-(.

Indeed, hard part is not to break DT compatibility later. Consider someone
will have to add regulator support later, which you omitted to do - having
both power supply and power gpio is a bit confusing, don't you think?

Anyway, time to stop arguing, feel free to do what you think is right, I do
not have anything important to add :)

	ladis