[PATCH v3 06/12] dt-bindings: display: sun4i-drm: Add A83T HDMI pipeline

[Rob Herring]

On Wed, Jan 17, 2018 at 09:14:15PM +0100, Jernej Skrabec wrote:
> This commit adds all necessary compatibles and descriptions needed to
> implement A83T HDMI pipeline.
> 
> Mixer is already properly described, so only compatible is added.
> 
> However, A83T TV TCON, which is connected to HDMI, doesn't have channel 0,
> contrary to all TCONs currently described. Because of that, TCON
> documentation is extended.
> 
> A83T features Synopsys DW HDMI controller with a custom PHY which looks
> like Synopsys Gen2 PHY with few additions. Since there is no
> documentation, needed properties were found out through experimentation
> and reading BSP code.
> 
> At the end, example is added for newer SoCs, which feature DE2 and DW
> HDMI.
> 
> Signed-off-by: Jernej Skrabec <jernej.skrabec at siol.net>
> ---
>  .../bindings/display/sunxi/sun4i-drm.txt           | 197 ++++++++++++++++++++-
>  1 file changed, 190 insertions(+), 7 deletions(-)
> 
> diff --git a/Documentation/devicetree/bindings/display/sunxi/sun4i-drm.txt b/Documentation/devicetree/bindings/display/sunxi/sun4i-drm.txt
> index cd626ee1147a..4fb380f3e53d 100644
> --- a/Documentation/devicetree/bindings/display/sunxi/sun4i-drm.txt
> +++ b/Documentation/devicetree/bindings/display/sunxi/sun4i-drm.txt
> @@ -64,6 +64,52 @@ Required properties:
>      first port should be the input endpoint. The second should be the
>      output, usually to an HDMI connector.
>  
> +DWC HDMI TX Encoder
> +-------------------
> +
> +The HDMI transmitter is a Synopsys DesignWare HDMI 1.4 TX controller IP
> +with Allwinner's own PHY IP. It supports audio and video outputs and CEC.
> +
> +These DT bindings follow the Synopsys DWC HDMI TX bindings defined in
> +Documentation/devicetree/bindings/display/bridge/dw_hdmi.txt with the
> +following device-specific properties.
> +
> +Required properties:
> +
> +  - compatible: value must be one of:
> +    * "allwinner,sun8i-a83t-dw-hdmi"
> +  - reg: base address and size of memory-mapped region
> +  - reg-io-width: See dw_hdmi.txt. Shall be 1.
> +  - interrupts: HDMI interrupt number
> +  - clocks: phandles to the clocks feeding the HDMI encoder
> +    * iahb: the HDMI bus clock
> +    * isfr: the HDMI register clock
> +  - clock-names: the clock names mentioned above
> +  - resets: phandle to the reset controller
> +  - reset-names: must be "ctrl"
> +  - phys: phandle to the DWC HDMI PHY
> +  - phy-names: must be "phy"
> +
> +  - ports: A ports node with endpoint definitions as defined in
> +    Documentation/devicetree/bindings/media/video-interfaces.txt. The
> +    first port should be the input endpoint. The second should be the
> +    output, usually to an HDMI connector.
> +
> +DWC HDMI PHY
> +------------
> +
> +Required properties:
> +  - compatible: value must be one of:
> +    * allwinner,sun8i-a83t-hdmi-phy
> +  - reg: base address and size of memory-mapped region
> +  - clocks: phandles to the clocks feeding the HDMI PHY
> +    * bus: the HDMI PHY interface clock
> +    * mod: the HDMI PHY module clock
> +    * tmds: TMDS clock
> +  - clock-names: the clock names mentioned above
> +  - resets: phandle to the reset controller driving the PHY
> +  - reset-names: must be "phy"
> +
>  TV Encoder
>  ----------
>  
> @@ -94,24 +140,23 @@ Required properties:
>     * allwinner,sun7i-a20-tcon
>     * allwinner,sun8i-a33-tcon
>     * allwinner,sun8i-a83t-tcon-lcd
> +   * allwinner,sun8i-a83t-tcon-tv
>     * allwinner,sun8i-v3s-tcon
>   - reg: base address and size of memory-mapped region
>   - interrupts: interrupt associated to this IP
> - - clocks: phandles to the clocks feeding the TCON. Three are needed:
> + - clocks: phandles to the clocks feeding the TCON. One is needed:
>     - 'ahb': the interface clocks
> -   - 'tcon-ch0': The clock driving the TCON channel 0

Well, it didn't look right before saying 3 are needed, but listing 2. 
However, you can't just change this as it affects all the other SoCs. 
This should probably be a separate patch.

>   - resets: phandles to the reset controllers driving the encoder
>     - "lcd": the reset line for the TCON channel 0
>  
>   - clock-names: the clock names mentioned above
>   - reset-names: the reset names mentioned above
> - - clock-output-names: Name of the pixel clock created

Why is this removed?

>  
>  - ports: A ports node with endpoint definitions as defined in
>    Documentation/devicetree/bindings/media/video-interfaces.txt. The
>    first port should be the input endpoint, the second one the output
>  
> -  The output may have multiple endpoints. The TCON has two channels,
> +  The output may have multiple endpoints. TCON can have two channels,

Perhaps you should say "can have 1 or 2 channels".

>    usually with the first channel being used for the panels interfaces
>    (RGB, LVDS, etc.), and the second being used for the outputs that
>    require another controller (TV Encoder, HDMI, etc.). The endpoints
> @@ -119,11 +164,16 @@ Required properties:
>    channel the endpoint is associated to. If that property is not
>    present, the endpoint number will be used as the channel number.
>  
> +When TCON supports channel 0 (all TCONs except TV TCON on A83T), two
> +more clocks are needed:
> +   - 'tcon-ch0': The clock driving the TCON channel 0

Looks like one clock to me.

> +   - clock-output-names: Name of the pixel clock created

It's better to not move this, but just add what compatibles it does or 
doesn't apply to.

> +
>  On SoCs other than the A33 and V3s, there is one more clock required:
>     - 'tcon-ch1': The clock driving the TCON channel 1
>  
> -On SoCs that support LVDS (all SoCs but the A13, H3, H5 and V3s), you
> -need one more reset line:
> +When TCON support LVDS (all TCONs except TV TCON on A83T and those found
> +in A13, H3, H5 and V3s SoCs), you need one more reset line:
>     - 'lvds': The reset line driving the LVDS logic
>  
>  And on the A23, A31, A31s and A33, you need one more clock line:
> @@ -226,6 +276,7 @@ supported.
>  Required properties:
>    - compatible: value must be one of:
>      * allwinner,sun8i-a83t-de2-mixer-0
> +    * allwinner,sun8i-a83t-de2-mixer-1
>      * allwinner,sun8i-v3s-de2-mixer
>    - reg: base address and size of the memory-mapped region.
>    - clocks: phandles to the clocks feeding the mixer
> @@ -261,7 +312,7 @@ Required properties:
>    - allwinner,pipelines: list of phandle to the display engine
>      frontends (DE 1.0) or mixers (DE 2.0) available.
>  
> -Example:
> +Example 1:
>  
>  panel: panel {
>  	compatible = "olimex,lcd-olinuxino-43-ts";
> @@ -460,3 +511,135 @@ display-engine {
>  	compatible = "allwinner,sun5i-a13-display-engine";
>  	allwinner,pipelines = <&fe0>;
>  };
> +
> +Example 2:

Is this really different enough to need an example? Examples don't 
need to enumerate all possible options. They are often wrong because 
they don't compile on their own and that creates a maintenance burden.

Rob