[PATCH 2/2] arm64: dts: sdm845: Add serial console support

[Stephen Boyd]

On 01/25, Rajendra Nayak wrote:
> diff --git a/arch/arm64/boot/dts/qcom/sdm845-pins.dtsi b/arch/arm64/boot/dts/qcom/sdm845-pins.dtsi
> new file mode 100644
> index 000000000000..b97f99e6f4b4
> --- /dev/null
> +++ b/arch/arm64/boot/dts/qcom/sdm845-pins.dtsi
> @@ -0,0 +1,32 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Copyright (c) 2018, The Linux Foundation. All rights reserved.
> + */
> +
> +&tlmm {

I'm not the maintainer, but I find this approach to the pins
really annoying. I have to flip to another file to figure out how
a board has configured the pins. And we may bring in a bunch of
settings that we don't ever use on some board too. Why can't we
put the settings in the board file directly?

> +	qup_uart2_default: qup_uart2_default {
> +		pinmux {
> +			function = "qup9";
> +			pins = "gpio4", "gpio5";
> +		};
> +
> +		pinconf {
> +			pins = "gpio4", "gpio5";
> +			drive-strength = <2>;
> +			bias-disable;
> +		};
> +	};
> +
> +	qup_uart2_sleep: qup_uart2_sleep {
> +		pinmux {
> +			function = "gpio";
> +			pins = "gpio4", "gpio5";
> +		};
> +
> +		pinconf {
> +			pins = "gpio4", "gpio5";
> +			drive-strength = <2>;
> +			bias-disable;
> +		};
> +	};
> +};
> diff --git a/arch/arm64/boot/dts/qcom/sdm845.dtsi b/arch/arm64/boot/dts/qcom/sdm845.dtsi
> index a21f4912b3e2..529f4ba3a1db 100644
> --- a/arch/arm64/boot/dts/qcom/sdm845.dtsi
> +++ b/arch/arm64/boot/dts/qcom/sdm845.dtsi
> @@ -4,6 +4,7 @@
>   */
>  
>  #include <dt-bindings/interrupt-controller/arm-gic.h>
> +#include <dt-bindings/clock/qcom,gcc-sdm845.h>
>  
>  / {
>  	model = "Qualcomm Technologies, Inc. SDM845";

I'd expect some sort of serial alias node stuff here too.

> @@ -304,5 +305,26 @@
>  			cell-index = <0>;
>  		};
>  
> +		qup_1: qcom,geni_se at ac0000 {
> +			compatible = "qcom,geni-se-qup";
> +			reg = <0xac0000 0x6000>;
> +		};
> +
> +		qup_uart2: serial at a84000 {
> +			compatible = "qcom,geni-console", "qcom,geni-uart";
> +			reg = <0xa84000 0x4000>;
> +			reg-names = "se_phys";
> +			clock-names = "se-clk", "m-ahb", "s-ahb";
> +			clocks = <&gcc GCC_QUPV3_WRAP1_S1_CLK>,
> +				 <&gcc GCC_QUPV3_WRAP_1_M_AHB_CLK>,
> +				 <&gcc GCC_QUPV3_WRAP_1_S_AHB_CLK>;
> +			pinctrl-names = "default", "sleep";
> +			pinctrl-0 = <&qup_uart2_default>;
> +			pinctrl-1 = <&qup_uart2_sleep>;
> +			interrupts = <GIC_SPI 354 IRQ_TYPE_NONE>;
> +			qcom,wrapper-core = <&qup_1>;

Is this binding still being reviewed? Ugly.

> +			status = "disabled";
> +		};
>  	};
>  };
> +#include "sdm845-pins.dtsi"

Why at the bottom?

-- 
Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum,
a Linux Foundation Collaborative Project