[PATCH v3] arm64: dts: rockchip: add roc-rk3328-cc board

djw at t-chip.com.cn djw at t-chip.com.cn
Mon Jan 22 18:10:17 PST 2018


From: Levin Du <djw at t-chip.com.cn>

Hi all,

v3:
Use pmic at 18 instead of rk805 at 18
Use macro definition RK_Pxx in gpio number

v2:
Use SPDX license tag

Thanks.

The roc-rk3328-cc is a credit card size single board computer using the
Rockchip RK3328 Quad-Core ARM Cortex A53 64-Bit Processor and supporting
up to 2GB 2133MHz LPDDR4 memory. It provides eMMC module socket, MicroSD
Card slot, USB 2.0/3.0, Gigabit Ethernet, HDMI/CVBS, Infrared Receiver,
SPDIF/I2S, and SPI/I2C/UART/PWM interfaces.

The devicetree currently supports basic peripherals.

Signed-off-by: Levin Du <djw at t-chip.com.cn>
---
 Documentation/devicetree/bindings/arm/rockchip.txt |   4 +
 arch/arm64/boot/dts/rockchip/Makefile              |   1 +
 arch/arm64/boot/dts/rockchip/rk3328-roc-cc.dts     | 276 +++++++++++++++++++++
 3 files changed, 281 insertions(+)
 create mode 100644 arch/arm64/boot/dts/rockchip/rk3328-roc-cc.dts

diff --git a/Documentation/devicetree/bindings/arm/rockchip.txt b/Documentation/devicetree/bindings/arm/rockchip.txt
index 326d24b..0f76a62 100644
--- a/Documentation/devicetree/bindings/arm/rockchip.txt
+++ b/Documentation/devicetree/bindings/arm/rockchip.txt
@@ -50,6 +50,10 @@ Rockchip platforms device tree bindings
     Required root node properties:
       - compatible = "firefly,firefly-rk3399", "rockchip,rk3399";
 
+- Firefly roc-rk3328-cc board:
+    Required root node properties:
+      - compatible = "firefly,roc-rk3328-cc", "rockchip,rk3328";
+
 - ChipSPARK PopMetal-RK3288 board:
     Required root node properties:
       - compatible = "chipspark,popmetal-rk3288", "rockchip,rk3288";
diff --git a/arch/arm64/boot/dts/rockchip/Makefile b/arch/arm64/boot/dts/rockchip/Makefile
index ce2701e..cf14b86 100644
--- a/arch/arm64/boot/dts/rockchip/Makefile
+++ b/arch/arm64/boot/dts/rockchip/Makefile
@@ -1,6 +1,7 @@
 # SPDX-License-Identifier: GPL-2.0
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-evb.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-rock64.dtb
+dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-roc-cc.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3368-evb-act8846.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3368-geekbox.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3368-orion-r68-meta.dtb
diff --git a/arch/arm64/boot/dts/rockchip/rk3328-roc-cc.dts b/arch/arm64/boot/dts/rockchip/rk3328-roc-cc.dts
new file mode 100644
index 0000000..5fc767d
--- /dev/null
+++ b/arch/arm64/boot/dts/rockchip/rk3328-roc-cc.dts
@@ -0,0 +1,276 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2017 T-Chip Intelligent Technology Co., Ltd
+ */
+
+/dts-v1/;
+#include "rk3328.dtsi"
+
+/ {
+	model = "Firefly roc-rk3328-cc";
+	compatible = "firefly,roc-rk3328-cc", "rockchip,rk3328";
+
+	chosen {
+		stdout-path = "serial2:1500000n8";
+	};
+
+	gmac_clkin: external-gmac-clock {
+		compatible = "fixed-clock";
+		clock-frequency = <125000000>;
+		clock-output-names = "gmac_clkin";
+		#clock-cells = <0>;
+	};
+
+	dc_12v: dc-12v {
+		compatible = "regulator-fixed";
+		regulator-name = "dc_12v";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <12000000>;
+		regulator-max-microvolt = <12000000>;
+	};
+
+	vcc_sd: sdmmc-regulator {
+		compatible = "regulator-fixed";
+		gpio = <&gpio0 RK_PD6 GPIO_ACTIVE_LOW>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&sdmmc0m1_gpio>;
+		regulator-name = "vcc_sd";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&vcc_io>;
+	};
+
+	vcc_host1_5v: vcc_otg_5v: vcc-host1-5v-regulator {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio1 RK_PD2 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&usb20_host_drv>;
+		regulator-name = "vcc_host1_5v";
+		regulator-always-on;
+		vin-supply = <&vcc_sys>;
+	};
+
+	vcc_sys: vcc-sys {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc_sys";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&dc_12v>;
+	};
+
+	vcc_phy: vcc-phy-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc_phy";
+		regulator-always-on;
+		regulator-boot-on;
+	};
+};
+
+&cpu0 {
+	cpu-supply = <&vdd_arm>;
+};
+
+&emmc {
+	bus-width = <8>;
+	cap-mmc-highspeed;
+	non-removable;
+	pinctrl-names = "default";
+	pinctrl-0 = <&emmc_clk &emmc_cmd &emmc_bus8>;
+	status = "okay";
+};
+
+&gmac2io {
+	assigned-clocks = <&cru SCLK_MAC2IO>, <&cru SCLK_MAC2IO_EXT>;
+	assigned-clock-parents = <&gmac_clkin>, <&gmac_clkin>;
+	clock_in_out = "input";
+	phy-supply = <&vcc_phy>;
+	phy-mode = "rgmii";
+	pinctrl-names = "default";
+	pinctrl-0 = <&rgmiim1_pins>;
+	snps,reset-gpio = <&gpio1 RK_PC2 GPIO_ACTIVE_LOW>;
+	snps,reset-active-low;
+	snps,reset-delays-us = <0 10000 50000>;
+	tx_delay = <0x25>;
+	rx_delay = <0x11>;
+	status = "okay";
+};
+
+&i2c1 {
+	status = "okay";
+
+	rk805: pmic at 18 {
+		compatible = "rockchip,rk805";
+		reg = <0x18>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <24 IRQ_TYPE_LEVEL_LOW>;
+		#clock-cells = <1>;
+		clock-output-names = "xin32k", "rk805-clkout2";
+		gpio-controller;
+		#gpio-cells = <2>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pmic_int_l>;
+		rockchip,system-power-controller;
+		wakeup-source;
+
+		vcc1-supply = <&vcc_sys>;
+		vcc2-supply = <&vcc_sys>;
+		vcc3-supply = <&vcc_sys>;
+		vcc4-supply = <&vcc_sys>;
+		vcc5-supply = <&vcc_io>;
+		vcc6-supply = <&vcc_io>;
+
+		regulators {
+			vdd_logic: DCDC_REG1 {
+				regulator-name = "vdd_logic";
+				regulator-min-microvolt = <712500>;
+				regulator-max-microvolt = <1450000>;
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1000000>;
+				};
+			};
+
+			vdd_arm: DCDC_REG2 {
+				regulator-name = "vdd_arm";
+				regulator-min-microvolt = <712500>;
+				regulator-max-microvolt = <1450000>;
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <950000>;
+				};
+			};
+
+			vcc_ddr: DCDC_REG3 {
+				regulator-name = "vcc_ddr";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-state-mem {
+					regulator-on-in-suspend;
+				};
+			};
+
+			vcc_io: DCDC_REG4 {
+				regulator-name = "vcc_io";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <3300000>;
+				};
+			};
+
+			vcc_18: LDO_REG1 {
+				regulator-name = "vcc_18";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1800000>;
+				};
+			};
+
+			vcc18_emmc: LDO_REG2 {
+				regulator-name = "vcc18_emmc";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1800000>;
+				};
+			};
+
+			vdd_10: LDO_REG3 {
+				regulator-name = "vdd_10";
+				regulator-min-microvolt = <1000000>;
+				regulator-max-microvolt = <1000000>;
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1000000>;
+				};
+			};
+		};
+	};
+};
+
+&pinctrl {
+	pmic {
+		pmic_int_l: pmic-int-l {
+			rockchip,pins = <1 RK_PD0 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+	};
+
+	usb2 {
+		usb20_host_drv: usb20-host-drv {
+			rockchip,pins = <1 RK_PD2 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+};
+
+&sdmmc {
+	bus-width = <4>;
+	cap-mmc-highspeed;
+	cap-sd-highspeed;
+	disable-wp;
+	max-frequency = <150000000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdmmc0_clk &sdmmc0_cmd &sdmmc0_dectn &sdmmc0_bus4>;
+	vmmc-supply = <&vcc_sd>;
+	status = "okay";
+};
+
+&tsadc {
+	status = "okay";
+};
+
+&uart2 {
+	status = "okay";
+};
+
+&u2phy {
+	status = "okay";
+};
+
+&u2phy_host {
+	status = "okay";
+};
+
+&u2phy_otg {
+	status = "okay";
+};
+
+&usb20_otg {
+	status = "okay";
+};
+
+&usb_host0_ehci {
+	status = "okay";
+};
+
+&usb_host0_ohci {
+	status = "okay";
+};
+
+&usbdrd3 {
+	status = "okay";
+};
+
+&usbdrd_dwc3 {
+	dr_mode = "host";
+	status = "okay";
+};
-- 
2.9.2





More information about the linux-arm-kernel mailing list