[PATCH 1/7] arm64: zynqmp: Add support for Xilinx zcu100-revC
Michal Simek
michal.simek at xilinx.com
Fri Jan 19 04:55:40 PST 2018
This board has 2GB of memory, i2c, sd, wifi sdio, spis, uarts, display
port and usbs.
Board is using fixed clocks because clock driver hasn't been merged yet.
Signed-off-by: Michal Simek <michal.simek at xilinx.com>
---
arch/arm64/boot/dts/xilinx/Makefile | 1 +
arch/arm64/boot/dts/xilinx/zynqmp-clk.dtsi | 213 ++++++++++++++++
arch/arm64/boot/dts/xilinx/zynqmp-zcu100-revC.dts | 298 ++++++++++++++++++++++
3 files changed, 512 insertions(+)
create mode 100644 arch/arm64/boot/dts/xilinx/zynqmp-clk.dtsi
create mode 100644 arch/arm64/boot/dts/xilinx/zynqmp-zcu100-revC.dts
diff --git a/arch/arm64/boot/dts/xilinx/Makefile b/arch/arm64/boot/dts/xilinx/Makefile
index eba179b23b17..7266a6a9c0cd 100644
--- a/arch/arm64/boot/dts/xilinx/Makefile
+++ b/arch/arm64/boot/dts/xilinx/Makefile
@@ -1,2 +1,3 @@
# SPDX-License-Identifier: GPL-2.0
dtb-$(CONFIG_ARCH_ZYNQMP) += zynqmp-ep108.dtb
+dtb-$(CONFIG_ARCH_ZYNQMP) += zynqmp-zcu100-revC.dtb
diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-clk.dtsi b/arch/arm64/boot/dts/xilinx/zynqmp-clk.dtsi
new file mode 100644
index 000000000000..9c09baca7dd7
--- /dev/null
+++ b/arch/arm64/boot/dts/xilinx/zynqmp-clk.dtsi
@@ -0,0 +1,213 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Clock specification for Xilinx ZynqMP
+ *
+ * (C) Copyright 2015 - 2018, Xilinx, Inc.
+ *
+ * Michal Simek <michal.simek at xilinx.com>
+ */
+
+/ {
+ clk100: clk100 {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <100000000>;
+ };
+
+ clk125: clk125 {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <125000000>;
+ };
+
+ clk200: clk200 {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <200000000>;
+ };
+
+ clk250: clk250 {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <250000000>;
+ };
+
+ clk300: clk300 {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <300000000>;
+ };
+
+ clk600: clk600 {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <600000000>;
+ };
+
+ dp_aclk: clock0 {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <100000000>;
+ clock-accuracy = <100>;
+ };
+
+ dp_aud_clk: clock1 {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <24576000>;
+ clock-accuracy = <100>;
+ };
+
+ dpdma_clk: dpdma_clk {
+ compatible = "fixed-clock";
+ #clock-cells = <0x0>;
+ clock-frequency = <533000000>;
+ };
+
+ drm_clock: drm_clock {
+ compatible = "fixed-clock";
+ #clock-cells = <0x0>;
+ clock-frequency = <262750000>;
+ clock-accuracy = <0x64>;
+ };
+};
+
+&can0 {
+ clocks = <&clk100 &clk100>;
+};
+
+&can1 {
+ clocks = <&clk100 &clk100>;
+};
+
+&fpd_dma_chan1 {
+ clocks = <&clk600>, <&clk100>;
+};
+
+&fpd_dma_chan2 {
+ clocks = <&clk600>, <&clk100>;
+};
+
+&fpd_dma_chan3 {
+ clocks = <&clk600>, <&clk100>;
+};
+
+&fpd_dma_chan4 {
+ clocks = <&clk600>, <&clk100>;
+};
+
+&fpd_dma_chan5 {
+ clocks = <&clk600>, <&clk100>;
+};
+
+&fpd_dma_chan6 {
+ clocks = <&clk600>, <&clk100>;
+};
+
+&fpd_dma_chan7 {
+ clocks = <&clk600>, <&clk100>;
+};
+
+&fpd_dma_chan8 {
+ clocks = <&clk600>, <&clk100>;
+};
+
+&lpd_dma_chan1 {
+ clocks = <&clk600>, <&clk100>;
+};
+
+&lpd_dma_chan2 {
+ clocks = <&clk600>, <&clk100>;
+};
+
+&lpd_dma_chan3 {
+ clocks = <&clk600>, <&clk100>;
+};
+
+&lpd_dma_chan4 {
+ clocks = <&clk600>, <&clk100>;
+};
+
+&lpd_dma_chan5 {
+ clocks = <&clk600>, <&clk100>;
+};
+
+&lpd_dma_chan6 {
+ clocks = <&clk600>, <&clk100>;
+};
+
+&lpd_dma_chan7 {
+ clocks = <&clk600>, <&clk100>;
+};
+
+&lpd_dma_chan8 {
+ clocks = <&clk600>, <&clk100>;
+};
+
+&gem0 {
+ clocks = <&clk125>, <&clk125>, <&clk125>;
+};
+
+&gem1 {
+ clocks = <&clk125>, <&clk125>, <&clk125>;
+};
+
+&gem2 {
+ clocks = <&clk125>, <&clk125>, <&clk125>;
+};
+
+&gem3 {
+ clocks = <&clk125>, <&clk125>, <&clk125>;
+};
+
+&gpio {
+ clocks = <&clk100>;
+};
+
+&i2c0 {
+ clocks = <&clk100>;
+};
+
+&i2c1 {
+ clocks = <&clk100>;
+};
+
+&sata {
+ clocks = <&clk250>;
+};
+
+&sdhci0 {
+ clocks = <&clk200 &clk200>;
+};
+
+&sdhci1 {
+ clocks = <&clk200 &clk200>;
+};
+
+&spi0 {
+ clocks = <&clk200 &clk200>;
+};
+
+&spi1 {
+ clocks = <&clk200 &clk200>;
+};
+
+&uart0 {
+ clocks = <&clk100 &clk100>;
+};
+
+&uart1 {
+ clocks = <&clk100 &clk100>;
+};
+
+&usb0 {
+ clocks = <&clk250>, <&clk250>;
+};
+
+&usb1 {
+ clocks = <&clk250>, <&clk250>;
+};
+
+&watchdog0 {
+ clocks = <&clk250>;
+};
diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zcu100-revC.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zcu100-revC.dts
new file mode 100644
index 000000000000..01f5f95806d3
--- /dev/null
+++ b/arch/arm64/boot/dts/xilinx/zynqmp-zcu100-revC.dts
@@ -0,0 +1,298 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * dts file for Xilinx ZynqMP ZCU100 revC
+ *
+ * (C) Copyright 2016 - 2018, Xilinx, Inc.
+ *
+ * Michal Simek <michal.simek at xilinx.com>
+ * Nathalie Chan King Choy <nathalie at xilinx.com>
+ */
+
+/dts-v1/;
+
+#include "zynqmp.dtsi"
+#include "zynqmp-clk.dtsi"
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+ model = "ZynqMP ZCU100 RevC";
+ compatible = "xlnx,zynqmp-zcu100-revC", "xlnx,zynqmp-zcu100", "xlnx,zynqmp";
+
+ aliases {
+ gpio0 = &gpio;
+ i2c0 = &i2c1;
+ rtc0 = &rtc;
+ serial0 = &uart1;
+ serial1 = &uart0;
+ serial2 = &dcc;
+ spi0 = &spi0;
+ spi1 = &spi1;
+ usb0 = &usb0;
+ usb1 = &usb1;
+ mmc0 = &sdhci0;
+ mmc1 = &sdhci1;
+ };
+
+ chosen {
+ bootargs = "earlycon";
+ stdout-path = "serial0:115200n8";
+ };
+
+ memory at 0 {
+ device_type = "memory";
+ reg = <0x0 0x0 0x0 0x80000000>;
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ autorepeat;
+ sw4 {
+ label = "sw4";
+ gpios = <&gpio 23 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_POWER>;
+ gpio-key,wakeup;
+ autorepeat;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ ds2 {
+ label = "ds2";
+ gpios = <&gpio 20 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
+ };
+
+ ds3 {
+ label = "ds3";
+ gpios = <&gpio 19 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "phy0tx"; /* WLAN tx */
+ default-state = "off";
+ };
+
+ ds4 {
+ label = "ds4";
+ gpios = <&gpio 18 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "phy0rx"; /* WLAN rx */
+ default-state = "off";
+ };
+
+ ds5 {
+ label = "ds5";
+ gpios = <&gpio 17 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "bluetooth-power";
+ };
+
+ vbus_det { /* U5 USB5744 VBUS detection via MIO25 */
+ label = "vbus_det";
+ gpios = <&gpio 25 GPIO_ACTIVE_HIGH>;
+ default-state = "on";
+ };
+
+ bt_power {
+ label = "bt_power";
+ gpios = <&gpio 8 GPIO_ACTIVE_HIGH>;
+ default-state = "on";
+ };
+ };
+
+ wmmcsdio_fixed: fixedregulator-mmcsdio {
+ compatible = "regulator-fixed";
+ regulator-name = "wmmcsdio_fixed";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ sdio_pwrseq: sdio_pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ reset-gpios = <&gpio 7 GPIO_ACTIVE_LOW>; /* WIFI_EN */
+ };
+};
+
+&dcc {
+ status = "okay";
+};
+
+&gpio {
+ status = "okay";
+ gpio-line-names = "UART1_TX", "UART1_RX", "UART0_RX", "UART0_TX", "I2C1_SCL",
+ "I2C1_SDA", "SPI1_SCLK", "WLAN_EN", "BT_EN", "SPI1_CS",
+ "SPI1_MISO", "SPI1_MOSI", "I2C_MUX_RESET", "SD0_DAT0", "SD0_DAT1",
+ "SD0_DAT2", "SD0_DAT3", "PS_LED3", "PS_LED2", "PS_LED1",
+ "PS_LED0", "SD0_CMD", "SD0_CLK", "GPIO_PB", "SD0_DETECT",
+ "VBUS_DET", "POWER_INT", "DP_AUX", "DP_HPD", "DP_OE",
+ "DP_AUX_IN", "INA226_ALERT", "PS_FP_PWR_EN", "PL_PWR_EN", "POWER_KILL",
+ "", "GPIO-A", "GPIO-B", "SPI0_SCLK", "GPIO-C",
+ "GPIO-D", "SPI0_CS", "SPI0_MISO", "SPI_MOSI", "GPIO-E",
+ "GPIO-F", "SD1_D0", "SD1_D1", "SD1_D2", "SD1_D3",
+ "SD1_CMD", "SD1_CLK", "USB0_CLK", "USB0_DIR", "USB0_DATA2",
+ "USB0_NXT", "USB0_DATA0", "USB0_DATA1", "USB0_STP", "USB0_DATA3",
+ "USB0_DATA4", "USB0_DATA5", "USB0_DATA6", "USB0_DATA7", "USB1_CLK",
+ "USB1_DIR", "USB1_DATA2", "USB1_NXT", "USB1_DATA0", "USB1_DATA1",
+ "USB1_STP", "USB1_DATA3", "USB1_DATA4", "USB1_DATA5", "USB1_DATA6",
+ "USB_DATA7", "WLAN_IRQ", "PMIC_IRQ", /* MIO end and EMIO start */
+ "", "",
+ "", "", "", "", "", "", "", "", "", "",
+ "", "", "", "", "", "", "", "", "", "",
+ "", "", "", "", "", "", "", "", "", "",
+ "", "", "", "", "", "", "", "", "", "",
+ "", "", "", "", "", "", "", "", "", "",
+ "", "", "", "", "", "", "", "", "", "",
+ "", "", "", "", "", "", "", "", "", "",
+ "", "", "", "", "", "", "", "", "", "",
+ "", "", "", "", "", "", "", "", "", "",
+ "", "", "", "";
+};
+
+&i2c1 {
+ status = "okay";
+ clock-frequency = <100000>;
+ i2cswitch at 75 { /* u11 */
+ compatible = "nxp,pca9548";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x75>;
+ i2csw_0: i2c at 0 { /* i2c mw 75 0 1 */
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+ /*
+ * LSEXP_I2C0
+ */
+ };
+ i2csw_1: i2c at 1 { /* i2c mw 75 0 2 */
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+ /*
+ * LSEXP_I2C1
+ */
+ };
+ i2csw_2: i2c at 2 { /* i2c mw 75 0 4 */
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <2>;
+ /*
+ * HSEXP_I2C2
+ */
+ };
+ i2csw_3: i2c at 3 { /* i2c mw 75 0 8 */
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <3>;
+ /*
+ * HSEXP_I2C3
+ */
+ };
+ i2csw_4: i2c at 4 { /* i2c mw 75 0 10 */
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x4>;
+
+ pmic: tps65086x at 5e { /* Custom TI PMIC u33 */
+ compatible = "ti,tps65086";
+ reg = <0x5e>;
+ interrupt-parent = <&gpio>;
+ interrupts = <77 GPIO_ACTIVE_LOW>;
+ #gpio-cells = <2>;
+ gpio-controller;
+ };
+ };
+ i2csw_5: i2c at 5 { /* i2c mw 75 0 20 */
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <5>;
+ /* PS_PMBUS */
+ ina226 at 40 { /* u35 */
+ compatible = "ti,ina226";
+ reg = <0x40>;
+ shunt-resistor = <10000>;
+ /* MIO31 is alert which should be routed to PMUFW */
+ };
+ };
+ i2csw_6: i2c at 6 { /* i2c mw 75 0 40 */
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <6>;
+ /*
+ * Not Connected
+ */
+ };
+ i2csw_7: i2c at 7 { /* i2c mw 75 0 80 */
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <7>;
+ /*
+ * usb5744 (DNP) - U5
+ * 100kHz - this is default freq for us
+ */
+ };
+ };
+};
+
+&rtc {
+ status = "okay";
+};
+
+/* SD0 only supports 3.3V, no level shifter */
+&sdhci0 {
+ status = "okay";
+ no-1-8-v;
+ broken-cd; /* CD has to be enabled by default */
+ disable-wp;
+};
+
+&sdhci1 {
+ status = "okay";
+ bus-width = <0x4>;
+ non-removable;
+ disable-wp;
+ cap-power-off-card;
+ mmc-pwrseq = <&sdio_pwrseq>;
+ vqmmc-supply = <&wmmcsdio_fixed>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ wlcore: wlcore at 2 {
+ compatible = "ti,wl1831";
+ reg = <2>;
+ interrupt-parent = <&gpio>;
+ interrupts = <76 IRQ_TYPE_EDGE_RISING>; /* MIO76 WLAN_IRQ 1V8 */
+ };
+};
+
+&spi0 { /* Low Speed connector */
+ status = "okay";
+};
+
+&spi1 { /* High Speed connector */
+ status = "okay";
+};
+
+&uart0 {
+ status = "okay";
+};
+
+&uart1 {
+ status = "okay";
+
+};
+
+/* ULPI SMSC USB3320 */
+&usb0 {
+ status = "okay";
+};
+
+/* ULPI SMSC USB3320 */
+&usb1 {
+ status = "okay";
+};
+
+&watchdog0 {
+ status = "okay";
+};
--
1.9.1
More information about the linux-arm-kernel
mailing list