[PATCH v5 1/6] ARM: dts: imx6: Add initial support for phyCORE-i.MX 6 SOM
Stefan Riedmueller
s.riedmueller at phytec.de
Tue Jan 9 08:09:55 PST 2018
This patch adds basic support for PHYTEC phyCORE-i.MX 6 SOM with i.MX
6Quad/Dual or i.MX 6DualLight/Solo.
Signed-off-by: Christian Hemp <c.hemp at phytec.de>
Signed-off-by: Stefan Christ <s.christ at phytec.de>
Signed-off-by: Christoph Fritz <chf.fritz at googlemail.com>
Signed-off-by: Stefan Riedmueller <s.riedmueller at phytec.de>
Reviewed-by: Fabio Estevam <fabio.estevam at nxp.com>
---
arch/arm/boot/dts/imx6qdl-phytec-phycore-som.dtsi | 279 ++++++++++++++++++++++
1 file changed, 279 insertions(+)
create mode 100644 arch/arm/boot/dts/imx6qdl-phytec-phycore-som.dtsi
diff --git a/arch/arm/boot/dts/imx6qdl-phytec-phycore-som.dtsi b/arch/arm/boot/dts/imx6qdl-phytec-phycore-som.dtsi
new file mode 100644
index 0000000..6486df3
--- /dev/null
+++ b/arch/arm/boot/dts/imx6qdl-phytec-phycore-som.dtsi
@@ -0,0 +1,279 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2018 PHYTEC Messtechnik GmbH
+ * Author: Christian Hemp <c.hemp at phytec.de>
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+ aliases {
+ rtc1 = &da9062_rtc;
+ rtc2 = &snvs_rtc;
+ };
+
+ /*
+ * Set the minimum memory size here and
+ * let the bootloader set the real size.
+ */
+ memory at 10000000 {
+ device_type = "memory";
+ reg = <0x10000000 0x8000000>;
+ };
+
+ gpio_leds_som: somleds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpioleds_som>;
+
+ som-led-green {
+ label = "phycore:green";
+ gpios = <&gpio1 4 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
+ };
+ };
+};
+
+&ecspi1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi1>;
+ cs-gpios = <&gpio3 19 GPIO_ACTIVE_LOW>;
+ status = "okay";
+
+ m25p80: flash at 0 {
+ compatible = "jedec,spi-nor";
+ spi-max-frequency = <20000000>;
+ reg = <0>;
+ status = "disabled";
+ };
+};
+
+&fec {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enet>;
+ phy-handle = <ðphy>;
+ phy-mode = "rgmii";
+ phy-supply = <&vdd_eth_io>;
+ phy-reset-gpios = <&gpio1 14 GPIO_ACTIVE_LOW>;
+ status = "disabled";
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ethphy: ethernet-phy at 3 {
+ reg = <3>;
+ txc-skew-ps = <1680>;
+ rxc-skew-ps = <1860>;
+ };
+ };
+};
+
+&gpmi {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpmi_nand>;
+ nand-on-flash-bbt;
+ status = "disabled";
+};
+
+&i2c3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c3>;
+ clock-frequency = <400000>;
+ status = "okay";
+
+ eeprom at 50 {
+ compatible = "atmel,24c32";
+ reg = <0x50>;
+ };
+
+ pmic at 58 {
+ compatible = "dlg,da9062";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pmic>;
+ reg = <0x58>;
+ interrupt-parent = <&gpio1>;
+ interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
+ interrupt-controller;
+
+ da9062_rtc: rtc {
+ compatible = "dlg,da9062-rtc";
+ };
+
+ watchdog {
+ compatible = "dlg,da9062-watchdog";
+ };
+
+ regulators {
+ vdd_arm: buck1 {
+ regulator-name = "vdd_arm";
+ regulator-min-microvolt = <730000>;
+ regulator-max-microvolt = <1380000>;
+ regulator-always-on;
+ };
+
+ vdd_soc: buck2 {
+ regulator-name = "vdd_soc";
+ regulator-min-microvolt = <730000>;
+ regulator-max-microvolt = <1380000>;
+ regulator-always-on;
+ };
+
+ vdd_ddr3_1p5: buck3 {
+ regulator-name = "vdd_ddr3";
+ regulator-min-microvolt = <1500000>;
+ regulator-max-microvolt = <1500000>;
+ regulator-always-on;
+ };
+
+ vdd_eth_1p2: buck4 {
+ regulator-name = "vdd_eth";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-always-on;
+ };
+
+ vdd_snvs: ldo1 {
+ regulator-name = "vdd_snvs";
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-always-on;
+ };
+
+ vdd_high: ldo2 {
+ regulator-name = "vdd_high";
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-always-on;
+ };
+
+ vdd_eth_io: ldo3 {
+ regulator-name = "vdd_eth_io";
+ regulator-min-microvolt = <2500000>;
+ regulator-max-microvolt = <2500000>;
+ };
+
+ vdd_emmc_1p8: ldo4 {
+ regulator-name = "vdd_emmc";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+ };
+ };
+};
+
+®_arm {
+ vin-supply = <&vdd_arm>;
+};
+
+®_pu {
+ vin-supply = <&vdd_soc>;
+};
+
+®_soc {
+ vin-supply = <&vdd_soc>;
+};
+
+&snvs_poweroff {
+ status = "okay";
+};
+
+&usdhc4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc4>;
+ bus-width = <8>;
+ non-removable;
+ vmmc-supply = <&vdd_emmc_1p8>;
+ status = "disabled";
+};
+
+&iomuxc {
+ pinctrl_enet: enetgrp {
+ fsl,pins = <
+ MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b0b0
+ MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b0b0
+ MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x1b0b0
+ MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x1b0b0
+ MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x1b0b0
+ MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x1b0b0
+ MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x1b0b0
+ MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x1b0b0
+ MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x1b0b0
+ MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b0b0
+ MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x1b0b0
+ MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x1b0b0
+ MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b0b0
+ MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b0b0
+ MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b0b0
+ MX6QDL_PAD_ENET_TX_EN__ENET_TX_EN 0x1b0b0
+ MX6QDL_PAD_SD2_DAT1__GPIO1_IO14 0x1b0b0
+ >;
+ };
+
+ pinctrl_gpioleds_som: gpioledssomgrp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_4__GPIO1_IO04 0x1b0b0
+ >;
+ };
+
+ pinctrl_gpmi_nand: gpminandgrp {
+ fsl,pins = <
+ MX6QDL_PAD_NANDF_CLE__NAND_CLE 0xb0b1
+ MX6QDL_PAD_NANDF_ALE__NAND_ALE 0xb0b1
+ MX6QDL_PAD_NANDF_WP_B__NAND_WP_B 0xb0b1
+ MX6QDL_PAD_NANDF_RB0__NAND_READY_B 0xb000
+ MX6QDL_PAD_NANDF_CS0__NAND_CE0_B 0xb0b1
+ MX6QDL_PAD_NANDF_CS1__NAND_CE1_B 0xb0b1
+ MX6QDL_PAD_NANDF_CS2__NAND_CE2_B 0xb0b1
+ MX6QDL_PAD_NANDF_CS3__NAND_CE3_B 0xb0b1
+ MX6QDL_PAD_SD4_CMD__NAND_RE_B 0xb0b1
+ MX6QDL_PAD_SD4_CLK__NAND_WE_B 0xb0b1
+ MX6QDL_PAD_NANDF_D0__NAND_DATA00 0xb0b1
+ MX6QDL_PAD_NANDF_D1__NAND_DATA01 0xb0b1
+ MX6QDL_PAD_NANDF_D2__NAND_DATA02 0xb0b1
+ MX6QDL_PAD_NANDF_D3__NAND_DATA03 0xb0b1
+ MX6QDL_PAD_NANDF_D4__NAND_DATA04 0xb0b1
+ MX6QDL_PAD_NANDF_D5__NAND_DATA05 0xb0b1
+ MX6QDL_PAD_NANDF_D6__NAND_DATA06 0xb0b1
+ MX6QDL_PAD_NANDF_D7__NAND_DATA07 0xb0b1
+ MX6QDL_PAD_SD4_DAT0__NAND_DQS 0x00b1
+ >;
+ };
+
+ pinctrl_i2c3: i2c3grp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_6__I2C3_SDA 0x4001b8b1
+ MX6QDL_PAD_GPIO_5__I2C3_SCL 0x4001b8b1
+ >;
+ };
+
+ pinctrl_ecspi1: ecspi1grp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D16__ECSPI1_SCLK 0x100b1
+ MX6QDL_PAD_EIM_D17__ECSPI1_MISO 0x100b1
+ MX6QDL_PAD_EIM_D18__ECSPI1_MOSI 0x100b1
+ MX6QDL_PAD_EIM_D19__GPIO3_IO19 0x1b0b0
+ >;
+ };
+
+ pinctrl_pmic: pmicgrp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_2__GPIO1_IO02 0x1b0b0
+ >;
+ };
+
+ pinctrl_usdhc4: usdhc4grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD4_CMD__SD4_CMD 0x17059
+ MX6QDL_PAD_SD4_CLK__SD4_CLK 0x10059
+ MX6QDL_PAD_SD4_DAT0__SD4_DATA0 0x17059
+ MX6QDL_PAD_SD4_DAT1__SD4_DATA1 0x17059
+ MX6QDL_PAD_SD4_DAT2__SD4_DATA2 0x17059
+ MX6QDL_PAD_SD4_DAT3__SD4_DATA3 0x17059
+ MX6QDL_PAD_SD4_DAT4__SD4_DATA4 0x17059
+ MX6QDL_PAD_SD4_DAT5__SD4_DATA5 0x17059
+ MX6QDL_PAD_SD4_DAT6__SD4_DATA6 0x17059
+ MX6QDL_PAD_SD4_DAT7__SD4_DATA7 0x17059
+ >;
+ };
+};
--
2.7.4
More information about the linux-arm-kernel
mailing list