[PATCH v2 8/8] arm64: dts: marvell: replace cpm by cp0, cps by cp1
Thomas Petazzoni
thomas.petazzoni at free-electrons.com
Tue Jan 2 06:55:58 PST 2018
In preparation for the introduction of more than 2 CPs in upcoming
SoCs, it makes sense to move away from the "CP master" (cpm) and "CP
slave" (cps) naming, and use instead cp0/cp1.
This commit is the result of:
sed 's%cpm%cp0g%' arch/arm64/boot/dts/marvell/*
sed 's%cps%cp1g%' arch/arm64/boot/dts/marvell/*
So it is a purely mechaninal change.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni at free-electrons.com>
Suggested-by: Hanna Hawa <hannah at marvell.com>
---
arch/arm64/boot/dts/marvell/armada-7040-db.dts | 46 ++++++-------
arch/arm64/boot/dts/marvell/armada-70x0.dtsi | 18 ++---
arch/arm64/boot/dts/marvell/armada-8020.dtsi | 2 +-
arch/arm64/boot/dts/marvell/armada-8040-db.dts | 80 +++++++++++------------
arch/arm64/boot/dts/marvell/armada-8040-mcbin.dts | 76 ++++++++++-----------
arch/arm64/boot/dts/marvell/armada-8040.dtsi | 2 +-
arch/arm64/boot/dts/marvell/armada-80x0.dtsi | 34 +++++-----
7 files changed, 129 insertions(+), 129 deletions(-)
diff --git a/arch/arm64/boot/dts/marvell/armada-7040-db.dts b/arch/arm64/boot/dts/marvell/armada-7040-db.dts
index 52b5341cb270..44c95b97a422 100644
--- a/arch/arm64/boot/dts/marvell/armada-7040-db.dts
+++ b/arch/arm64/boot/dts/marvell/armada-7040-db.dts
@@ -61,7 +61,7 @@
reg = <0x0 0x0 0x0 0x80000000>;
};
- cpm_reg_usb3_0_vbus: cpm-usb3-0-vbus {
+ cp0_reg_usb3_0_vbus: cp0-usb3-0-vbus {
compatible = "regulator-fixed";
regulator-name = "usb3h0-vbus";
regulator-min-microvolt = <5000000>;
@@ -70,7 +70,7 @@
gpio = <&expander0 0 GPIO_ACTIVE_HIGH>;
};
- cpm_reg_usb3_1_vbus: cpm-usb3-1-vbus {
+ cp0_reg_usb3_1_vbus: cp0-usb3-1-vbus {
compatible = "regulator-fixed";
regulator-name = "usb3h1-vbus";
regulator-min-microvolt = <5000000>;
@@ -79,14 +79,14 @@
gpio = <&expander0 1 GPIO_ACTIVE_HIGH>;
};
- cpm_usb3_0_phy: cpm-usb3-0-phy {
+ cp0_usb3_0_phy: cp0-usb3-0-phy {
compatible = "usb-nop-xceiv";
- vcc-supply = <&cpm_reg_usb3_0_vbus>;
+ vcc-supply = <&cp0_reg_usb3_0_vbus>;
};
- cpm_usb3_1_phy: cpm-usb3-1-phy {
+ cp0_usb3_1_phy: cp0-usb3-1-phy {
compatible = "usb-nop-xceiv";
- vcc-supply = <&cpm_reg_usb3_1_vbus>;
+ vcc-supply = <&cp0_reg_usb3_1_vbus>;
};
};
@@ -129,11 +129,11 @@
};
-&cpm_pcie2 {
+&cp0_pcie2 {
status = "okay";
};
-&cpm_i2c0 {
+&cp0_i2c0 {
status = "okay";
clock-frequency = <100000>;
@@ -156,7 +156,7 @@
};
};
-&cpm_nand {
+&cp0_nand {
/*
* SPI on CPM and NAND have common pins on this board. We can
* use only one at a time. To enable the NAND (whihch will
@@ -186,7 +186,7 @@
};
-&cpm_spi1 {
+&cp0_spi1 {
status = "okay";
spi-flash at 0 {
@@ -214,17 +214,17 @@
};
};
-&cpm_sata0 {
+&cp0_sata0 {
status = "okay";
};
-&cpm_usb3_0 {
- usb-phy = <&cpm_usb3_0_phy>;
+&cp0_usb3_0 {
+ usb-phy = <&cp0_usb3_0_phy>;
status = "okay";
};
-&cpm_usb3_1 {
- usb-phy = <&cpm_usb3_1_phy>;
+&cp0_usb3_1 {
+ usb-phy = <&cp0_usb3_1_phy>;
status = "okay";
};
@@ -235,14 +235,14 @@
non-removable;
};
-&cpm_sdhci0 {
+&cp0_sdhci0 {
status = "okay";
bus-width = <4>;
no-1-8-v;
cd-gpios = <&expander0 12 GPIO_ACTIVE_LOW>;
};
-&cpm_mdio {
+&cp0_mdio {
status = "okay";
phy0: ethernet-phy at 0 {
@@ -253,28 +253,28 @@
};
};
-&cpm_ethernet {
+&cp0_ethernet {
status = "okay";
};
-&cpm_eth0 {
+&cp0_eth0 {
status = "okay";
/* Network PHY */
phy-mode = "10gbase-kr";
/* Generic PHY, providing serdes lanes */
- phys = <&cpm_comphy2 0>;
+ phys = <&cp0_comphy2 0>;
};
-&cpm_eth1 {
+&cp0_eth1 {
status = "okay";
/* Network PHY */
phy = <&phy0>;
phy-mode = "sgmii";
/* Generic PHY, providing serdes lanes */
- phys = <&cpm_comphy0 1>;
+ phys = <&cp0_comphy0 1>;
};
-&cpm_eth2 {
+&cp0_eth2 {
status = "okay";
phy = <&phy1>;
phy-mode = "rgmii-id";
diff --git a/arch/arm64/boot/dts/marvell/armada-70x0.dtsi b/arch/arm64/boot/dts/marvell/armada-70x0.dtsi
index 9917cff3dae6..f63b4fbd642b 100644
--- a/arch/arm64/boot/dts/marvell/armada-70x0.dtsi
+++ b/arch/arm64/boot/dts/marvell/armada-70x0.dtsi
@@ -46,17 +46,17 @@
/ {
aliases {
- gpio1 = &cpm_gpio1;
- gpio2 = &cpm_gpio2;
- spi1 = &cpm_spi0;
- spi2 = &cpm_spi1;
+ gpio1 = &cp0_gpio1;
+ gpio2 = &cp0_gpio2;
+ spi1 = &cp0_spi0;
+ spi2 = &cp0_spi1;
};
};
/*
* Instantiate the CP110
*/
-#define CP110_NAME cpm
+#define CP110_NAME cp0
#define CP110_BASE f2000000
#define CP110_PCIE_IO_BASE 0xf9000000
#define CP110_PCIE_MEM_BASE 0xf6000000
@@ -74,16 +74,16 @@
#undef CP110_PCIE1_BASE
#undef CP110_PCIE2_BASE
-&cpm_gpio1 {
+&cp0_gpio1 {
status = "okay";
};
-&cpm_gpio2 {
+&cp0_gpio2 {
status = "okay";
};
-&cpm_syscon0 {
- cpm_pinctrl: pinctrl {
+&cp0_syscon0 {
+ cp0_pinctrl: pinctrl {
compatible = "marvell,armada-7k-pinctrl";
nand_pins: nand-pins {
diff --git a/arch/arm64/boot/dts/marvell/armada-8020.dtsi b/arch/arm64/boot/dts/marvell/armada-8020.dtsi
index 0ba0bc942598..3318d6b0214b 100644
--- a/arch/arm64/boot/dts/marvell/armada-8020.dtsi
+++ b/arch/arm64/boot/dts/marvell/armada-8020.dtsi
@@ -60,6 +60,6 @@
* oscillator so this one is let enabled.
*/
-&cpm_rtc {
+&cp0_rtc {
status = "disabled";
};
diff --git a/arch/arm64/boot/dts/marvell/armada-8040-db.dts b/arch/arm64/boot/dts/marvell/armada-8040-db.dts
index b1f6cccc5081..13e3209d554a 100644
--- a/arch/arm64/boot/dts/marvell/armada-8040-db.dts
+++ b/arch/arm64/boot/dts/marvell/armada-8040-db.dts
@@ -61,46 +61,46 @@
reg = <0x0 0x0 0x0 0x80000000>;
};
- cpm_reg_usb3_0_vbus: cpm-usb3-0-vbus {
+ cp0_reg_usb3_0_vbus: cp0-usb3-0-vbus {
compatible = "regulator-fixed";
- regulator-name = "cpm-usb3h0-vbus";
+ regulator-name = "cp0-usb3h0-vbus";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
enable-active-high;
gpio = <&expander0 0 GPIO_ACTIVE_HIGH>;
};
- cpm_reg_usb3_1_vbus: cpm-usb3-1-vbus {
+ cp0_reg_usb3_1_vbus: cp0-usb3-1-vbus {
compatible = "regulator-fixed";
- regulator-name = "cpm-usb3h1-vbus";
+ regulator-name = "cp0-usb3h1-vbus";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
enable-active-high;
gpio = <&expander0 1 GPIO_ACTIVE_HIGH>;
};
- cpm_usb3_0_phy: cpm-usb3-0-phy {
+ cp0_usb3_0_phy: cp0-usb3-0-phy {
compatible = "usb-nop-xceiv";
- vcc-supply = <&cpm_reg_usb3_0_vbus>;
+ vcc-supply = <&cp0_reg_usb3_0_vbus>;
};
- cpm_usb3_1_phy: cpm-usb3-1-phy {
+ cp0_usb3_1_phy: cp0-usb3-1-phy {
compatible = "usb-nop-xceiv";
- vcc-supply = <&cpm_reg_usb3_1_vbus>;
+ vcc-supply = <&cp0_reg_usb3_1_vbus>;
};
- cps_reg_usb3_0_vbus: cps-usb3-0-vbus {
+ cp1_reg_usb3_0_vbus: cp1-usb3-0-vbus {
compatible = "regulator-fixed";
- regulator-name = "cps-usb3h0-vbus";
+ regulator-name = "cp1-usb3h0-vbus";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
enable-active-high;
gpio = <&expander1 0 GPIO_ACTIVE_HIGH>;
};
- cps_usb3_0_phy: cps-usb3-0-phy {
+ cp1_usb3_0_phy: cp1-usb3-0-phy {
compatible = "usb-nop-xceiv";
- vcc-supply = <&cps_reg_usb3_0_vbus>;
+ vcc-supply = <&cp1_reg_usb3_0_vbus>;
};
};
@@ -144,16 +144,16 @@
};
/* CON6 on CP0 expansion */
-&cpm_pcie0 {
+&cp0_pcie0 {
status = "okay";
};
/* CON5 on CP0 expansion */
-&cpm_pcie2 {
+&cp0_pcie2 {
status = "okay";
};
-&cpm_i2c0 {
+&cp0_i2c0 {
status = "okay";
clock-frequency = <100000>;
@@ -178,23 +178,23 @@
};
/* CON4 on CP0 expansion */
-&cpm_sata0 {
+&cp0_sata0 {
status = "okay";
};
/* CON9 on CP0 expansion */
-&cpm_usb3_0 {
- usb-phy = <&cpm_usb3_0_phy>;
+&cp0_usb3_0 {
+ usb-phy = <&cp0_usb3_0_phy>;
status = "okay";
};
/* CON10 on CP0 expansion */
-&cpm_usb3_1 {
- usb-phy = <&cpm_usb3_1_phy>;
+&cp0_usb3_1 {
+ usb-phy = <&cp0_usb3_1_phy>;
status = "okay";
};
-&cpm_mdio {
+&cp0_mdio {
status = "okay";
phy1: ethernet-phy at 1 {
@@ -202,42 +202,42 @@
};
};
-&cpm_ethernet {
+&cp0_ethernet {
status = "okay";
};
-&cpm_eth0 {
+&cp0_eth0 {
status = "okay";
phy-mode = "10gbase-kr";
};
-&cpm_eth2 {
+&cp0_eth2 {
status = "okay";
phy = <&phy1>;
phy-mode = "rgmii-id";
};
/* CON6 on CP1 expansion */
-&cps_pcie0 {
+&cp1_pcie0 {
status = "okay";
};
/* CON7 on CP1 expansion */
-&cps_pcie1 {
+&cp1_pcie1 {
status = "okay";
};
/* CON5 on CP1 expansion */
-&cps_pcie2 {
+&cp1_pcie2 {
status = "okay";
};
-&cps_i2c0 {
+&cp1_i2c0 {
status = "okay";
clock-frequency = <100000>;
};
-&cps_spi1 {
+&cp1_spi1 {
status = "okay";
spi-flash at 0 {
@@ -272,14 +272,14 @@
* Proper NAND usage will require DPR-76 to be in position 1-2, which disables
* MDIO signal of CP1.
*/
-&cps_nand {
+&cp1_nand {
num-cs = <1>;
pinctrl-0 = <&nand_pins>, <&nand_rb>;
pinctrl-names = "default";
nand-ecc-strength = <4>;
nand-ecc-step-size = <512>;
marvell,nand-enable-arbiter;
- marvell,system-controller = <&cps_syscon0>;
+ marvell,system-controller = <&cp1_syscon0>;
nand-on-flash-bbt;
partition at 0 {
@@ -297,22 +297,22 @@
};
/* CON4 on CP1 expansion */
-&cps_sata0 {
+&cp1_sata0 {
status = "okay";
};
/* CON9 on CP1 expansion */
-&cps_usb3_0 {
- usb-phy = <&cps_usb3_0_phy>;
+&cp1_usb3_0 {
+ usb-phy = <&cp1_usb3_0_phy>;
status = "okay";
};
/* CON10 on CP1 expansion */
-&cps_usb3_1 {
+&cp1_usb3_1 {
status = "okay";
};
-&cps_mdio {
+&cp1_mdio {
status = "okay";
phy0: ethernet-phy at 0 {
@@ -320,16 +320,16 @@
};
};
-&cps_ethernet {
+&cp1_ethernet {
status = "okay";
};
-&cps_eth0 {
+&cp1_eth0 {
status = "okay";
phy-mode = "10gbase-kr";
};
-&cps_eth1 {
+&cp1_eth1 {
status = "okay";
phy = <&phy0>;
phy-mode = "rgmii-id";
@@ -341,7 +341,7 @@
non-removable;
};
-&cpm_sdhci0 {
+&cp0_sdhci0 {
status = "okay";
bus-width = <8>;
non-removable;
diff --git a/arch/arm64/boot/dts/marvell/armada-8040-mcbin.dts b/arch/arm64/boot/dts/marvell/armada-8040-mcbin.dts
index b3350827ee55..c7aca67bd244 100644
--- a/arch/arm64/boot/dts/marvell/armada-8040-mcbin.dts
+++ b/arch/arm64/boot/dts/marvell/armada-8040-mcbin.dts
@@ -84,9 +84,9 @@
v_5v0_usb3_hst_vbus: regulator-usb3-vbus0 {
compatible = "regulator-fixed";
enable-active-high;
- gpio = <&cpm_gpio2 15 GPIO_ACTIVE_HIGH>;
+ gpio = <&cp0_gpio2 15 GPIO_ACTIVE_HIGH>;
pinctrl-names = "default";
- pinctrl-0 = <&cpm_xhci_vbus_pins>;
+ pinctrl-0 = <&cp0_xhci_vbus_pins>;
regulator-name = "v_5v0_usb3_hst_vbus";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
@@ -120,17 +120,17 @@
vqmmc-supply = <&v_vddo_h>;
};
-&cpm_i2c0 {
+&cp0_i2c0 {
clock-frequency = <100000>;
pinctrl-names = "default";
- pinctrl-0 = <&cpm_i2c0_pins>;
+ pinctrl-0 = <&cp0_i2c0_pins>;
status = "okay";
};
-&cpm_i2c1 {
+&cp0_i2c1 {
clock-frequency = <100000>;
pinctrl-names = "default";
- pinctrl-0 = <&cpm_i2c1_pins>;
+ pinctrl-0 = <&cp0_i2c1_pins>;
status = "okay";
i2c-switch at 70 {
@@ -157,9 +157,9 @@
};
};
-&cpm_mdio {
+&cp0_mdio {
pinctrl-names = "default";
- pinctrl-0 = <&cpm_ge_mdio_pins>;
+ pinctrl-0 = <&cp0_ge_mdio_pins>;
status = "okay";
ge_phy: ethernet-phy at 0 {
@@ -167,44 +167,44 @@
};
};
-&cpm_pcie0 {
+&cp0_pcie0 {
pinctrl-names = "default";
- pinctrl-0 = <&cpm_pcie_pins>;
+ pinctrl-0 = <&cp0_pcie_pins>;
num-lanes = <4>;
num-viewport = <8>;
- reset-gpio = <&cpm_gpio1 20 GPIO_ACTIVE_LOW>;
+ reset-gpio = <&cp0_gpio1 20 GPIO_ACTIVE_LOW>;
status = "okay";
};
-&cpm_pinctrl {
- cpm_ge_mdio_pins: ge-mdio-pins {
+&cp0_pinctrl {
+ cp0_ge_mdio_pins: ge-mdio-pins {
marvell,pins = "mpp32", "mpp34";
marvell,function = "ge";
};
- cpm_i2c1_pins: i2c1-pins {
+ cp0_i2c1_pins: i2c1-pins {
marvell,pins = "mpp35", "mpp36";
marvell,function = "i2c1";
};
- cpm_i2c0_pins: i2c0-pins {
+ cp0_i2c0_pins: i2c0-pins {
marvell,pins = "mpp37", "mpp38";
marvell,function = "i2c0";
};
- cpm_xhci_vbus_pins: xhci0-vbus-pins {
+ cp0_xhci_vbus_pins: xhci0-vbus-pins {
marvell,pins = "mpp47";
marvell,function = "gpio";
};
- cpm_pcie_pins: pcie-pins {
+ cp0_pcie_pins: pcie-pins {
marvell,pins = "mpp52";
marvell,function = "gpio";
};
- cpm_sdhci_pins: sdhci-pins {
+ cp0_sdhci_pins: sdhci-pins {
marvell,pins = "mpp55", "mpp56", "mpp57", "mpp58", "mpp59",
"mpp60", "mpp61";
marvell,function = "sdio";
};
};
-&cpm_xmdio {
+&cp0_xmdio {
status = "okay";
phy0: ethernet-phy at 0 {
@@ -218,83 +218,83 @@
};
};
-&cpm_ethernet {
+&cp0_ethernet {
status = "okay";
};
-&cpm_eth0 {
+&cp0_eth0 {
status = "okay";
/* Network PHY */
phy = <&phy0>;
phy-mode = "10gbase-kr";
/* Generic PHY, providing serdes lanes */
- phys = <&cpm_comphy4 0>;
+ phys = <&cp0_comphy4 0>;
};
-&cpm_sata0 {
+&cp0_sata0 {
/* CPM Lane 0 - U29 */
status = "okay";
};
-&cpm_sdhci0 {
+&cp0_sdhci0 {
/* U6 */
broken-cd;
bus-width = <4>;
pinctrl-names = "default";
- pinctrl-0 = <&cpm_sdhci_pins>;
+ pinctrl-0 = <&cp0_sdhci_pins>;
status = "okay";
vqmmc-supply = <&v_3_3>;
};
-&cpm_usb3_0 {
+&cp0_usb3_0 {
/* J38? - USB2.0 only */
status = "okay";
};
-&cpm_usb3_1 {
+&cp0_usb3_1 {
/* J38? - USB2.0 only */
status = "okay";
};
-&cps_ethernet {
+&cp1_ethernet {
status = "okay";
};
-&cps_eth0 {
+&cp1_eth0 {
status = "okay";
/* Network PHY */
phy = <&phy8>;
phy-mode = "10gbase-kr";
/* Generic PHY, providing serdes lanes */
- phys = <&cps_comphy4 0>;
+ phys = <&cp1_comphy4 0>;
};
-&cps_eth1 {
+&cp1_eth1 {
/* CPS Lane 0 - J5 (Gigabit RJ45) */
status = "okay";
/* Network PHY */
phy = <&ge_phy>;
phy-mode = "sgmii";
/* Generic PHY, providing serdes lanes */
- phys = <&cps_comphy0 1>;
+ phys = <&cp1_comphy0 1>;
};
-&cps_pinctrl {
- cps_spi1_pins: spi1-pins {
+&cp1_pinctrl {
+ cp1_spi1_pins: spi1-pins {
marvell,pins = "mpp12", "mpp13", "mpp14", "mpp15", "mpp16";
marvell,function = "spi1";
};
};
-&cps_sata0 {
+&cp1_sata0 {
/* CPS Lane 1 - U32 */
/* CPS Lane 3 - U31 */
status = "okay";
};
-&cps_spi1 {
+&cp1_spi1 {
pinctrl-names = "default";
- pinctrl-0 = <&cps_spi1_pins>;
+ pinctrl-0 = <&cp1_spi1_pins>;
status = "okay";
spi-flash at 0 {
@@ -304,7 +304,7 @@
};
};
-&cps_usb3_0 {
+&cp1_usb3_0 {
/* CPS Lane 2 - CON7 */
usb-phy = <&usb3h0_phy>;
status = "okay";
diff --git a/arch/arm64/boot/dts/marvell/armada-8040.dtsi b/arch/arm64/boot/dts/marvell/armada-8040.dtsi
index 60fe84f5cbcc..83d2b40e5981 100644
--- a/arch/arm64/boot/dts/marvell/armada-8040.dtsi
+++ b/arch/arm64/boot/dts/marvell/armada-8040.dtsi
@@ -59,6 +59,6 @@
* disable it. However, the RTC clock in CP slave is connected to the
* oscillator so this one is let enabled.
*/
-&cpm_rtc {
+&cp0_rtc {
status = "disabled";
};
diff --git a/arch/arm64/boot/dts/marvell/armada-80x0.dtsi b/arch/arm64/boot/dts/marvell/armada-80x0.dtsi
index 5e038e7b7b30..0d36b0fa7153 100644
--- a/arch/arm64/boot/dts/marvell/armada-80x0.dtsi
+++ b/arch/arm64/boot/dts/marvell/armada-80x0.dtsi
@@ -46,19 +46,19 @@
/ {
aliases {
- gpio1 = &cps_gpio1;
- gpio2 = &cpm_gpio2;
- spi1 = &cpm_spi0;
- spi2 = &cpm_spi1;
- spi3 = &cps_spi0;
- spi4 = &cps_spi1;
+ gpio1 = &cp1_gpio1;
+ gpio2 = &cp0_gpio2;
+ spi1 = &cp0_spi0;
+ spi2 = &cp0_spi1;
+ spi3 = &cp1_spi0;
+ spi4 = &cp1_spi1;
};
};
/*
* Instantiate the master CP110
*/
-#define CP110_NAME cpm
+#define CP110_NAME cp0
#define CP110_BASE f2000000
#define CP110_PCIE_IO_BASE 0xf9000000
#define CP110_PCIE_MEM_BASE 0xf6000000
@@ -79,7 +79,7 @@
/*
* Instantiate the slave CP110
*/
-#define CP110_NAME cps
+#define CP110_NAME cp1
#define CP110_BASE f4000000
#define CP110_PCIE_IO_BASE 0xfd000000
#define CP110_PCIE_MEM_BASE 0xfa000000
@@ -98,23 +98,23 @@
#undef CP110_PCIE2_BASE
/* The 80x0 has two CP blocks, but uses only one block from each. */
-&cps_gpio1 {
+&cp1_gpio1 {
status = "okay";
};
-&cpm_gpio2 {
+&cp0_gpio2 {
status = "okay";
};
-&cpm_syscon0 {
- cpm_pinctrl: pinctrl {
- compatible = "marvell,armada-8k-cpm-pinctrl";
+&cp0_syscon0 {
+ cp0_pinctrl: pinctrl {
+ compatible = "marvell,armada-8k-cp0-pinctrl";
};
};
-&cps_syscon0 {
- cps_pinctrl: pinctrl {
- compatible = "marvell,armada-8k-cps-pinctrl";
+&cp1_syscon0 {
+ cp1_pinctrl: pinctrl {
+ compatible = "marvell,armada-8k-cp1-pinctrl";
nand_pins: nand-pins {
marvell,pins =
@@ -135,7 +135,7 @@
};
};
-&cps_crypto {
+&cp1_crypto {
/*
* The cryptographic engine found on the cp110
* master is enabled by default at the SoC
--
2.14.3
More information about the linux-arm-kernel
mailing list