[PATCH v2 4/4] pintcrl: support bias-disable of generic and special pins simultaneously

Zhiyong Tao zhiyong.tao at mediatek.com
Wed Feb 28 19:47:52 PST 2018


On Wed, 2018-02-28 at 15:49 +0800, Zhiyong Tao wrote:
> On Wed, 2018-02-28 at 15:33 +0800, Sean Wang wrote:
> > On Mon, 2018-02-26 at 16:34 +0800, Zhiyong Tao wrote:
> > > For generic pins, parameter "arg" is 0 or 1.
> > > For special pins, bias-disable is set by R0R1,
> > > so we need transmited "00" to set bias-disable
> > > When we set "bias-disable" as high-z property,
> > > the parameter should be "MTK_PUPD_SET_R1R0_00".
> > > 
> > > Signed-off-by: Zhiyong Tao <zhiyong.tao at mediatek.com>
> > > ---
> > >  drivers/pinctrl/mediatek/pinctrl-mtk-common.c | 13 +++++++++++--
> > >  1 file changed, 11 insertions(+), 2 deletions(-)
> > > 
> > > diff --git a/drivers/pinctrl/mediatek/pinctrl-mtk-common.c b/drivers/pinctrl/mediatek/pinctrl-mtk-common.c
> > > index 3cf384f..e88ba04 100644
> > > --- a/drivers/pinctrl/mediatek/pinctrl-mtk-common.c
> > > +++ b/drivers/pinctrl/mediatek/pinctrl-mtk-common.c
> > > @@ -301,8 +301,17 @@ static int mtk_pconf_set_pull_select(struct mtk_pinctrl *pctl,
> > >  	 * resistor bit, so we need this special handle.
> > >  	 */
> > >  	if (pctl->devdata->spec_pull_set) {
> > > -		ret = pctl->devdata->spec_pull_set(mtk_get_regmap(pctl, pin),
> > > -			pin, pctl->devdata->port_align, isup, arg);
> > > +		if (enable) {
> > > +			ret = pctl->devdata->spec_pull_set(
> > > +				mtk_get_regmap(pctl, pin), pin,
> > > +				pctl->devdata->port_align, isup,
> > > +				arg);
> > > +		} else {
> > > +			ret = pctl->devdata->spec_pull_set(
> > > +				mtk_get_regmap(pctl, pin), pin,
> > > +				pctl->devdata->port_align, isup,
> > > +				MTK_PUPD_SET_R1R0_00);
> > > +		}
> > 
> > 
> > it looks like you can use as following snippet with reusing original
> > logic and less effort on maintaining these common code (?)
> ==> Thanks for your suggestion very much. It seems better.
> I will change it in v3.

==>
 Hi sean,

we try it in our site. we can't change like this.
Because we will check "arg" after setting "arg = MTK_PUPD_SET_R1R0_00;".
following snippet which check "arg" value is o or 1. If it not, which
will print error. so we can't change like this.
/* For generic pull config, default arg value should be 0 or 1. */
if (arg != 0 && arg != 1) {
	dev_err(pctl->dev, "invalid pull-up argument %d on pin %d .\n", arg,
pin);
	return -EINVAL;
}

Thanks.
> > 
> > 
> > if (pctl->devdata->spec_pull_set) {
> > 	+ if (!enable)
> > 	+ 	arg = MTK_PUPD_SET_R1R0_00;
> > 
> > 	ret = pctl->devdata->spec_pull_set(mtk_get_regmap(pctl, pin),
> > 		pin, pctl->devdata->port_align, isup, arg);
> > 
> > 
> > Also, it's better to add more comments to such kind of special path for
> > allowing future SoCs to follow and extend more easily.
> 
> ==> Thanks for your suggestion very much. I will add more comments here.
> > 
> > >  		if (!ret)
> > >  			return 0;
> > >  	}
> > 
> > 
> 





More information about the linux-arm-kernel mailing list