[PATCH 08/10] gpio: Add gpio driver for Actions OWL S900 SoC
Manivannan Sadhasivam
manivannan.sadhasivam at linaro.org
Wed Feb 28 09:49:04 PST 2018
Add gpio driver for Actions Semi OWL family S900 SoC. Set of registers
controlling the gpio shares the same register range with pinctrl block.
GPIO registers are organized as 6 banks and each bank controls the
maximum of 32 gpios.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam at linaro.org>
---
drivers/gpio/Kconfig | 8 ++
drivers/gpio/Makefile | 1 +
drivers/gpio/gpio-owl.c | 218 ++++++++++++++++++++++++++++++++++++++++++++++++
3 files changed, 227 insertions(+)
create mode 100644 drivers/gpio/gpio-owl.c
diff --git a/drivers/gpio/Kconfig b/drivers/gpio/Kconfig
index 8dbb2280538d..09ceb98e2434 100644
--- a/drivers/gpio/Kconfig
+++ b/drivers/gpio/Kconfig
@@ -364,6 +364,14 @@ config GPIO_OMAP
help
Say yes here to enable GPIO support for TI OMAP SoCs.
+config GPIO_OWL
+ tristate "Actions OWL GPIO support"
+ default ARCH_ACTIONS
+ depends on ARCH_ACTIONS || COMPILE_TEST
+ depends on OF_GPIO
+ help
+ Say yes here to enable GPIO support for Actions OWL SoCs.
+
config GPIO_PL061
bool "PrimeCell PL061 GPIO support"
depends on ARM_AMBA
diff --git a/drivers/gpio/Makefile b/drivers/gpio/Makefile
index cccb0d40846c..b2bb11d4675f 100644
--- a/drivers/gpio/Makefile
+++ b/drivers/gpio/Makefile
@@ -91,6 +91,7 @@ obj-$(CONFIG_GPIO_MXC) += gpio-mxc.o
obj-$(CONFIG_GPIO_MXS) += gpio-mxs.o
obj-$(CONFIG_GPIO_OCTEON) += gpio-octeon.o
obj-$(CONFIG_GPIO_OMAP) += gpio-omap.o
+obj-$(CONFIG_GPIO_OWL) += gpio-owl.o
obj-$(CONFIG_GPIO_PCA953X) += gpio-pca953x.o
obj-$(CONFIG_GPIO_PCF857X) += gpio-pcf857x.o
obj-$(CONFIG_GPIO_PCH) += gpio-pch.o
diff --git a/drivers/gpio/gpio-owl.c b/drivers/gpio/gpio-owl.c
new file mode 100644
index 000000000000..98f2e98197bc
--- /dev/null
+++ b/drivers/gpio/gpio-owl.c
@@ -0,0 +1,218 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * OWL SoC's GPIO driver
+ *
+ * Copyright (c) 2018 Linaro Ltd.
+ * Author: Manivannan Sadhasivam <manivannan.sadhasivam at linaro.org>
+ */
+
+#include <linux/bitops.h>
+#include <linux/err.h>
+#include <linux/gpio/driver.h>
+#include <linux/io.h>
+#include <linux/module.h>
+#include <linux/of_address.h>
+#include <linux/of_device.h>
+#include <linux/platform_device.h>
+#include <linux/slab.h>
+
+#define GPIO_OUTEN 0x0000
+#define GPIO_INEN 0x0004
+#define GPIO_DAT 0x0008
+
+#define OWL_GPIO_PORT_A 0
+#define OWL_GPIO_PORT_B 1
+#define OWL_GPIO_PORT_C 2
+#define OWL_GPIO_PORT_D 3
+#define OWL_GPIO_PORT_E 4
+#define OWL_GPIO_PORT_F 5
+
+struct owl_gpio_port {
+ const char *name;
+ unsigned int offset;
+ unsigned int pins;
+};
+
+struct owl_gpio {
+ struct gpio_chip gpio;
+ const struct owl_gpio_port *port;
+ void __iomem *base;
+ int id;
+};
+
+static void owl_gpio_set_reg(void __iomem *base, unsigned int pin, int flag)
+{
+ u32 val;
+
+ val = readl_relaxed(base);
+
+ if (flag)
+ val |= BIT(pin);
+ else
+ val &= ~BIT(pin);
+
+ writel_relaxed(val, base);
+}
+
+static int owl_gpio_request(struct gpio_chip *chip, unsigned int offset)
+{
+ struct owl_gpio *gpio = gpiochip_get_data(chip);
+ const struct owl_gpio_port *port = gpio->port;
+ void __iomem *gpio_base = gpio->base + port->offset;
+
+ /*
+ * GPIOs have higher priority over other modules, so either setting
+ * them as OUT or IN is sufficient
+ */
+ owl_gpio_set_reg(gpio_base + GPIO_OUTEN, offset, true);
+
+ return 0;
+}
+
+static void owl_gpio_free(struct gpio_chip *chip, unsigned int offset)
+{
+ struct owl_gpio *gpio = gpiochip_get_data(chip);
+ const struct owl_gpio_port *port = gpio->port;
+ void __iomem *gpio_base = gpio->base + port->offset;
+
+ /* disable gpio output */
+ owl_gpio_set_reg(gpio_base + GPIO_OUTEN, offset, false);
+
+ /* disable gpio input */
+ owl_gpio_set_reg(gpio_base + GPIO_INEN, offset, false);
+}
+
+static int owl_gpio_get(struct gpio_chip *chip, unsigned int offset)
+{
+ struct owl_gpio *gpio = gpiochip_get_data(chip);
+ const struct owl_gpio_port *port = gpio->port;
+ void __iomem *gpio_base = gpio->base + port->offset;
+ u32 val;
+
+ val = readl_relaxed(gpio_base + GPIO_DAT);
+
+ return !!(val & BIT(offset));
+}
+
+static void owl_gpio_set(struct gpio_chip *chip, unsigned int offset, int value)
+{
+ struct owl_gpio *gpio = gpiochip_get_data(chip);
+ const struct owl_gpio_port *port = gpio->port;
+ void __iomem *gpio_base = gpio->base + port->offset;
+ u32 val;
+
+ val = readl_relaxed(gpio_base + GPIO_DAT);
+
+ if (value)
+ val |= BIT(offset);
+ else
+ val &= ~BIT(offset);
+
+ writel_relaxed(val, gpio_base + GPIO_DAT);
+}
+
+static int owl_gpio_direction_input(struct gpio_chip *chip, unsigned int offset)
+{
+ struct owl_gpio *gpio = gpiochip_get_data(chip);
+ const struct owl_gpio_port *port = gpio->port;
+ void __iomem *gpio_base = gpio->base + port->offset;
+
+ owl_gpio_set_reg(gpio_base + GPIO_OUTEN, offset, false);
+ owl_gpio_set_reg(gpio_base + GPIO_INEN, offset, true);
+
+ return 0;
+}
+
+static int owl_gpio_direction_output(struct gpio_chip *chip,
+ unsigned int offset, int value)
+{
+ struct owl_gpio *gpio = gpiochip_get_data(chip);
+ const struct owl_gpio_port *port = gpio->port;
+ void __iomem *gpio_base = gpio->base + port->offset;
+
+ owl_gpio_set_reg(gpio_base + GPIO_INEN, offset, false);
+ owl_gpio_set_reg(gpio_base + GPIO_OUTEN, offset, true);
+ owl_gpio_set(chip, offset, value);
+
+ return 0;
+}
+
+#define OWL_GPIO_PORT(port, base, count) \
+ [OWL_GPIO_PORT_##port] = { \
+ .name = #port, \
+ .offset = base, \
+ .pins = count, \
+ }
+
+static const struct owl_gpio_port s900_gpio_ports[] = {
+ OWL_GPIO_PORT(A, 0x0000, 32),
+ OWL_GPIO_PORT(B, 0x000C, 32),
+ OWL_GPIO_PORT(C, 0x0018, 12),
+ OWL_GPIO_PORT(D, 0x0024, 30),
+ OWL_GPIO_PORT(E, 0x0030, 32),
+ OWL_GPIO_PORT(F, 0x00F0, 8),
+};
+
+static int owl_gpio_probe(struct platform_device *pdev)
+{
+ struct owl_gpio *gpio;
+ const struct owl_gpio_port *port;
+ int ret;
+
+ gpio = devm_kzalloc(&pdev->dev, sizeof(*gpio), GFP_KERNEL);
+ if (!gpio)
+ return -ENOMEM;
+
+ gpio->base = of_iomap(pdev->dev.of_node, 0);
+ if (IS_ERR(gpio->base))
+ return PTR_ERR(gpio->base);
+
+ gpio->id = of_alias_get_id(pdev->dev.of_node, "gpio");
+ if (gpio->id < 0)
+ return gpio->id;
+
+ port = &s900_gpio_ports[gpio->id];
+
+ gpio->gpio.request = owl_gpio_request;
+ gpio->gpio.free = owl_gpio_free;
+ gpio->gpio.get = owl_gpio_get;
+ gpio->gpio.set = owl_gpio_set;
+ gpio->gpio.direction_input = owl_gpio_direction_input;
+ gpio->gpio.direction_output = owl_gpio_direction_output;
+
+ gpio->gpio.base = -1;
+ gpio->gpio.parent = &pdev->dev;
+ gpio->gpio.label = port->name;
+ gpio->gpio.ngpio = port->pins;
+
+ gpio->port = port;
+
+ platform_set_drvdata(pdev, gpio);
+
+ ret = devm_gpiochip_add_data(&pdev->dev, &gpio->gpio, gpio);
+ if (ret < 0) {
+ dev_err(&pdev->dev, "Failed to register gpiochip\n");
+ return ret;
+ }
+
+ return 0;
+}
+
+static const struct of_device_id owl_gpio_of_match[] = {
+ { .compatible = "actions,s900-gpio", },
+ { /* sentinel */ },
+};
+MODULE_DEVICE_TABLE(of, owl_gpio_of_match);
+
+static struct platform_driver owl_gpio_driver = {
+ .driver = {
+ .name = "owl-gpio",
+ .of_match_table = owl_gpio_of_match,
+ },
+ .probe = owl_gpio_probe,
+};
+module_platform_driver(owl_gpio_driver);
+
+MODULE_AUTHOR("Manivannan Sadhasivam <manivannan.sadhasivam at linaro.org>");
+MODULE_DESCRIPTION("Actions Semi OWL SoCs GPIO driver");
+MODULE_LICENSE("GPL");
--
2.14.1
More information about the linux-arm-kernel
mailing list