[PATCH v2 2/2] i2c: add support for Socionext SynQuacer I2C controller

[Ard Biesheuvel]

On 23 February 2018 at 13:12, Andy Shevchenko <andy.shevchenko at gmail.com> wrote:
> On Fri, Feb 23, 2018 at 2:40 PM, Ard Biesheuvel
> <ard.biesheuvel at linaro.org> wrote:
>> On 23 February 2018 at 12:27, Andy Shevchenko <andy.shevchenko at gmail.com> wrote:
>>> On Thu, Feb 22, 2018 at 9:16 PM, Ard Biesheuvel
>>> <ard.biesheuvel at linaro.org> wrote:
...
>>>> +       ret = device_property_read_u32(&pdev->dev, "clock-frequency",
>>>> +                                      &speed_khz);
>>>> +       if (ret) {
>>>> +               dev_err(&pdev->dev,
>>>> +                       "Missing clock-frequency property\n");
>>>> +               return -EINVAL;
>>>> +       }
>>>> +       speed_khz /= 1000;
>
>>>> +       if (dev_of_node(&pdev->dev)) {
>>>> +               i2c->clk = devm_clk_get(&pdev->dev, "pclk");
>>>> +               if (IS_ERR(i2c->clk)) {
>>>> +                       dev_err(&pdev->dev, "cannot get clock\n");
>>>> +                       return PTR_ERR(i2c->clk);
>>>> +               }
>>>> +               dev_dbg(&pdev->dev, "clock source %p\n", i2c->clk);
>>>> +
>>>> +               i2c->clkrate = clk_get_rate(i2c->clk);
>>>> +               dev_dbg(&pdev->dev, "clock rate %d\n", i2c->clkrate);
>>>> +               clk_prepare_enable(i2c->clk);
>>>> +       } else {
>>>> +               ret = device_property_read_u32(&pdev->dev,
>>>> +                                              "socionext,pclk-rate",
>>>> +                                              &i2c->clkrate);
>>>> +               if (ret)
>>>> +                       return ret;
>>>> +       }
>>>
>>> Okay, I got this case. It's more likely the one in 8250_dw.c.
>>>
>>> Can you do the similar way?
>
>> Could you elaborate?
>
> --- 8< --- 8< --- 8< ---
>         device_property_read_u32(dev, "clock-frequency", &p->uartclk);
>
>        /* If there is separate baudclk, get the rate from it. */
>        data->clk = devm_clk_get(dev, "baudclk");
> ...
>        if (IS_ERR(data->clk) && PTR_ERR(data->clk) == -EPROBE_DEFER)
>                return -EPROBE_DEFER;
>        if (!IS_ERR_OR_NULL(data->clk)) {
>                err = clk_prepare_enable(data->clk);
>                if (err)
>                        dev_warn(dev, "could not enable optional baudclk: %d\n",
>                                 err);
>                else
>                        p->uartclk = clk_get_rate(data->clk);
>        }
>
>        /* If no clock rate is defined, fail. */
>        if (!p->uartclk) {
>                dev_err(dev, "clock rate not defined\n");
>                err = -EINVAL;
>                goto err_clk;
> --- 8< --- 8< --- 8< ---
>
> Replace 'baudclk' with 'pclk' and p->uartclk with i2c->clkrate in
> above and you are almost done.
>

I don't think this is better. The generic DT I2C 'clock-frequency'
property denotes the bus clock rate not the rate of the clock that
feeds the IP block. This is rather different from the UART bindings.

Also, I don't want to support 'socionext,pclk-rate' for DT platforms,
only for ACPI platforms.

>>>> +       i2c->irq = platform_get_irq(pdev, 0);
>>>> +       if (i2c->irq <= 0) {
>>>
>>> < 0 ?
>>>
>>> On some platforms IRQ == 0 might be valid.
>
>> Are you sure about that?
>
> Yes. I fixed some cases on one of a such.
>
>> http://yarchive.net/comp/linux/no_irq.html
>
> I agree with Linus from software IRQ (and nowadays luckily we are
> using IRQ descriptors), but I disagree with him from hardware
> prospective.
> 0 is totally valid HW IRQ line. In hardware there is no descriptor
> (except, yes, MSI and alike cases), it's just a wire with an index.
>
> So, while drivers are getting better in code prospective (though I
> don't see many of them comparing this to 0), the IRQ framework is
> changing itself as well.
>
> At which circumstances we might get 0 in the first place?
>
> Second question, doesn't request_irq() fail on irq==0 if it's not
> supported as valid by platform?
>

Yes, I suppose it does.

I'll change it to '< 0'