[PATCH v2 19/19] ARM64: dts: r8a77965: Add EtherAVB device node

[Sergei Shtylyov]

On 02/21/2018 08:31 PM, Simon Horman wrote:

>>>>> Populate the ethernet at e6800000 device node to enable Ethernet interface
>>>>> for R-Car M3-N (r8a77965) SoC.
>>>>>
>>>>> Signed-off-by: Jacopo Mondi <jacopo+renesas at jmondi.org>
>>>>> Reviewed-by: Geert Uytterhoeven <geert+renesas at glider.be>
>>>>>
>>>>> ---
>>>>> v1 -> v2:
>>>>> - Replace ALWAYS_ON power area identifier with numeric constant
>>>>> ---
>>>>>  arch/arm64/boot/dts/renesas/r8a77965.dtsi | 43 ++++++++++++++++++++++++++++++-
>>>>>  1 file changed, 42 insertions(+), 1 deletion(-)
>>>>>
>>>>> diff --git a/arch/arm64/boot/dts/renesas/r8a77965.dtsi b/arch/arm64/boot/dts/renesas/r8a77965.dtsi
>>>>> index 55f05f7..c249895 100644
>>>>> --- a/arch/arm64/boot/dts/renesas/r8a77965.dtsi
>>>>> +++ b/arch/arm64/boot/dts/renesas/r8a77965.dtsi
>>>>> @@ -520,7 +520,48 @@
>>>>>  		};
>>>>>
>>>>>  		avb: ethernet at e6800000 {
>>>>> -			/* placeholder */
>>>>> +			compatible = "renesas,etheravb-r8a77965",
>>>>> +				     "renesas,etheravb-rcar-gen3";
>>>>> +			reg = <0 0xe6800000 0 0x800>, <0 0xe6a00000 0 0x10000>;
>>>>> +			interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>,
>>>>> +				     <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>,
>>>>> +				     <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>,
>>>>> +				     <GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>,
>>>>> +				     <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>,
>>>>> +				     <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>,
>>>>> +				     <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>,
>>>>> +				     <GIC_SPI 46 IRQ_TYPE_LEVEL_HIGH>,
>>>>> +				     <GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>,
>>>>> +				     <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>,
>>>>> +				     <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>,
>>>>> +				     <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>,
>>>>> +				     <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>,
>>>>> +				     <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>,
>>>>> +				     <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>,
>>>>> +				     <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>,
>>>>> +				     <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>,
>>>>> +				     <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>,
>>>>> +				     <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>,
>>>>> +				     <GIC_SPI 58 IRQ_TYPE_LEVEL_HIGH>,
>>>>> +				     <GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH>,
>>>>> +				     <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>,
>>>>> +				     <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>,
>>>>> +				     <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>,
>>>>> +				     <GIC_SPI 63 IRQ_TYPE_LEVEL_HIGH>;
>>>>> +			interrupt-names = "ch0", "ch1", "ch2", "ch3",
>>>>> +					  "ch4", "ch5", "ch6", "ch7",
>>>>> +					  "ch8", "ch9", "ch10", "ch11",
>>>>> +					  "ch12", "ch13", "ch14", "ch15",
>>>>> +					  "ch16", "ch17", "ch18", "ch19",
>>>>> +					  "ch20", "ch21", "ch22", "ch23",
>>>>> +					  "ch24";
>>>>> +			clocks = <&cpg CPG_MOD 812>;
>>>>> +			power-domains = <&sysc 32>;
>>>>> +			resets = <&cpg 812>;
>>>>> +			phy-mode = "rgmii-txid";
>>>>
>>>>    Why not just "rgmii"? TX delay is a board specific detail, no?
>>>>
>>> I admit I took this one straight from r8a7796 dtsi.
>>> Would you like to me resend and change this?
>>
>>    Yes, unless Simon would fix it while merging...
> 
> Can I confirm the desired change is s/rgmii-txid/rgmii/ ?

   Yes.

> If so I can fix that up.
 
   Thank you!

MBR, Sergei