[PATCH v2 2/2] arm: dts: sun6i: a31s: fix: bpi-m2: add missing regulators

[Philipp Rossak]

This patch fixes a bootproblem with the Bananapi M2 board. Since there
are some regulators missing we add them right now. Those values come
from the schematic, below you can find a small overview:

* reg_aldo1:  3,3V, powers the wifi
* reg_aldo2:  2,5V, powers the IO of the RTL8211E
* reg_aldo3:  3,3V, powers the audio

* reg_dldo1:  3,0V, powers the RTL8211E
* reg_dldo2:  2,8V, powers the analog part of the csi
* reg_dldo3:  3,3V, powers misc
* reg_eldo1:  1,8V, powers the csi
* reg_ldo_io1:1,8V, powers the gpio

* reg_dc5ldo: needs to be always on

This patch updates also the vmmc-supply properties on the mmc0 and mmc2
node to use the allready existent regulators.
We can now remove the sunxi-common-regulators.dtsi include since we
don't need it anymore.

Fixes: 7daa21370075 ("ARM: dts: sunxi: Add regulators for Sinovoip
BPI-M2")

Signed-off-by: Philipp Rossak <embed3d at gmail.com>
---
 arch/arm/boot/dts/sun6i-a31s-sinovoip-bpi-m2.dts | 61 ++++++++++++++++++++++--
 1 file changed, 58 insertions(+), 3 deletions(-)

diff --git a/arch/arm/boot/dts/sun6i-a31s-sinovoip-bpi-m2.dts b/arch/arm/boot/dts/sun6i-a31s-sinovoip-bpi-m2.dts
index fb34f32502cf..b2758dd8ce43 100644
--- a/arch/arm/boot/dts/sun6i-a31s-sinovoip-bpi-m2.dts
+++ b/arch/arm/boot/dts/sun6i-a31s-sinovoip-bpi-m2.dts
@@ -42,7 +42,6 @@
 
 /dts-v1/;
 #include "sun6i-a31s.dtsi"
-#include "sunxi-common-regulators.dtsi"
 #include <dt-bindings/gpio/gpio.h>
 
 / {
@@ -99,6 +98,7 @@
 	pinctrl-0 = <&gmac_pins_rgmii_a>, <&gmac_phy_reset_pin_bpi_m2>;
 	phy = <&phy1>;
 	phy-mode = "rgmii";
+	phy-supply = <&reg_dldo1>;
 	snps,reset-gpio = <&pio 0 21 GPIO_ACTIVE_HIGH>; /* PA21 */
 	snps,reset-active-low;
 	snps,reset-delays-us = <0 10000 30000>;
@@ -118,7 +118,7 @@
 &mmc0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_bpi_m2>;
-	vmmc-supply = <&reg_vcc3v0>;
+	vmmc-supply = <&reg_dcdc1>;
 	bus-width = <4>;
 	cd-gpios = <&pio 0 4 GPIO_ACTIVE_HIGH>; /* PA4 */
 	cd-inverted;
@@ -132,7 +132,7 @@
 &mmc2 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&mmc2_pins_a>;
-	vmmc-supply = <&reg_vcc3v0>;
+	vmmc-supply = <&reg_aldo1>;
 	mmc-pwrseq = <&mmc2_pwrseq>;
 	bus-width = <4>;
 	non-removable;
@@ -195,7 +195,28 @@
 
 #include "axp22x.dtsi"
 
+&reg_aldo1 {
+	regulator-min-microvolt = <3300000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-name = "vcc-wifi";
+};
+
+&reg_aldo2 {
+	regulator-always-on;
+	regulator-min-microvolt = <2500000>;
+	regulator-max-microvolt = <2500000>;
+	regulator-name = "vcc-gmac";
+};
+
+&reg_aldo3 {
+	regulator-always-on;
+	regulator-min-microvolt = <3000000>;
+	regulator-max-microvolt = <3000000>;
+	regulator-name = "avcc";
+};
+
 &reg_dc5ldo {
+	regulator-always-on;
 	regulator-min-microvolt = <700000>;
 	regulator-max-microvolt = <1320000>;
 	regulator-name = "vdd-cpus";
@@ -235,6 +256,40 @@
 	regulator-name = "vcc-dram";
 };
 
+&reg_dldo1 {
+	regulator-min-microvolt = <3000000>;
+	regulator-max-microvolt = <3000000>;
+	regulator-name = "vcc-mac";
+};
+
+&reg_dldo2 {
+	regulator-min-microvolt = <2800000>;
+	regulator-max-microvolt = <2800000>;
+	regulator-name = "avdd-csi";
+};
+
+&reg_dldo3 {
+	regulator-always-on;
+	regulator-min-microvolt = <3300000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-name = "vcc-pb";
+};
+
+&reg_eldo1 {
+	regulator-min-microvolt = <1800000>;
+	regulator-max-microvolt = <1800000>;
+	regulator-name = "vdd-csi";
+	status = "okay";
+};
+
+&reg_ldo_io1 {
+	regulator-always-on;
+	regulator-min-microvolt = <1800000>;
+	regulator-max-microvolt = <1800000>;
+	regulator-name = "vcc-pm-cpus";
+	status = "okay";
+};
+
 &uart0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart0_pins_a>;
-- 
2.11.0